The series O Erlenmeyer and filter flask mantles help prevent thermal strain on unusually susceptible heavy-walled vessels.

Variable speed control Compact size Heavy duty Fuse protected Smaller size makes this ideal for use on a lab bench; in small incubations, refrigerators, biological cabinets and fume hoods; or in any other area where space is limited. Specifically designed to handle both large…

With a patented Glas-Col Snorkel Stopper, you'll never again have to take time to open the stopcock and relieve pressure when vigorously shaking a separatory funnel, because our Snorkel Stopper does the task automatically. If you use a Glas-Col shaker, you can simply load the funnels onto it…

This timed control turns the output load on and off and then repeats the cycle. Each position on the knob from LO to HI represents a specific cycle time where the on time ranges from 6 to 100 percent. For example the LO setting represents a total cycle of approximately 60 seconds with an on time of…

Continuous shearing and blending action mixes with introducing air Corrosion-resistant stainless steel Teflon® TFE bushing 11,500 rpm 120V or 240V models available Includes lab clamp The upward flow stirrer may be used effectively with pharmaceuticals, cosmetics,…

Heating mantles are preferred to Bunsen burners or hot plates for organic liquids. They provide even heating (no hot spots) and maximum surface coverage for better temperature uniformity. The Series TM spherical flask mantle covers only the flask's bottom half, letting you see its full…

This heating mantle can heat metal beakers safely and efficiently. Inner glass-fabric ayers prevent contact of heating elements and vessel walls. The mantle is designed for straight-walled, flat bottom vessels.

The series O Erlenmeyer and filter flask mantles help prevent thermal strain on unusually susceptible heavy-walled vessels.

Sample grinding is designed to disrupt cell or tissue samples. It utilizes a shearing action by forcing the material between the side wall where homogenization occurs. Homogenization with a mortar and pestle is a low-throughput method, used most often for relatively small batches.

Splash Guards can help prevent mantle damage from chemical spillage and improve operating safety when heating liquids. The shield is appropriate for use with low-wattage mantles (Series M and TM) for flasks, glass beakers, steel beakers, resin flasks, and Buchner funnels. A rugged silicone pad…

Thorough mixing action Variable speed control Speed range of 2-80 rpm Dry Powder Rotator has the drive bar set at a 20° angle so the motion of the rotator closely reproduces the mixing action achieved when mixing by hand, making it useful for working with hard-to-mix powders. Not only is the…

The series O Buchner funnel mantle provides gentle heat for solutions that must be filtered while warm.

The series STM mantles perform the same function as series TM heating mantles, plus operations requiring more heat. With an upper internal operating temperature of 650 deg C, these mantles resist burnout. STM1400 and STM1500 have 3 in legs for cool lab benches, are sealed, and have inert gas purge fittings.

These funnel mantles allow extraction of fluids while hot, preventing solidification of viscous material in cold stopcocks. The thickness of the fiberglass fabric between heating elements and soft glass wall of the separatory funnel prevents thermal strain and the resultant cracking. Viewing is…

Manually adjustable; has a percentage-timer design and no sensing element Regulates mantles, tapes and cords, as well as small furnaces, ovens, hot plates, dies and other applications requiring stepless control Can be used on any non-inductive loads to its rated capacity of 1,440 watts …

Smooth rotation and repeatability Totally enclosed motors Variable speed motor drives are designed to make the homogenizing process faster, safer and more thorough. These variable-speed drives feature totally enclosed motors. For high-speed operations, the direct drive shaft is…

The series O Erlenmeyer and filter flask mantles help prevent thermal strain on unusually susceptible heavy-walled vessels.

The Buchner funnel mantle provides convenient support for funnel and gentle heat for solutions that must be kept warm during transfer. Durable support bracket slides over mast of ring stand, enabling mantle to be positioned at any convenient height above receiver.

This series O mantle is a hemispherical style, meaning it covers only the bottom half of the flask. This allows full view of the flask contents. The mantle accommodates single- and multi-neck flasks.

With a patented Glas-Col Snorkel Stopper, you'll never again have to take time to open the stopcock and relieve pressure when vigorously shaking a separatory funnel, because our Snorkel Stopper does the task automatically. If you use a Glas-Col shaker, you can simply load the funnels onto it…

In both permanent and temporary applications, this tape heats odd lengths of glass tubes and metal pipes. Ribbon-type heating elements running lengthwise in the tape are encased in durable glass braid and are impregnated and covered with tough silicone rubber, which insulates stranded terminal…

These supports are adjustable in height to provide convenient locations of series M mantles. If a drain container is necessary, one side of the leg brace may be easily removed to accommodate it. The adjustable legs are self-storing when not in use.

Splash guards can help prevent mantle damage from chemical spillage and improve operating safety when heating liquids. The shield is appropriate for use with low-wattage mantles (series M and TM) for flasks, glass beakers, steel beakers, resin flasks, and Buchner funnels. A rugged silicone pad…

This tube holder lets you use the Bench-Top Shaker for Mojonnier fat extraction. Each holder accepts up to four flasks, 37 mm in diameter.Maximum of two holders can be shaken at one time. The load max of up to five pounds (2.27 kg) need not be balanced. Unstoppered flasks may be shaken vertically.…

The Glas-Col stirring bar is a laboratory equipment used with 2 mL to 5 Liters flask while conducting wide range of experiments. It is suitable for use in research facilities and chemical laboratories. It features reliable and sturdy construction which ensures durability.

The centrifuge tube holder allows shaking vertically to let gases escape, or horizontally with stoppers secured by a plate. Each holder accommodates up to eight 15 mL glass tubes of up to 16 mm diameter, 126-160 mm long (stoppered) Up to 2 holders can be shaken at once Load Capacity:…

Griffin beaker heaters Maximum internal temperature 450°C Resilient and pliable interior, which cradles fragile beakers Heat is concentrated at the bottom, so even small liquid volumes can be heated Glass cloth mantle conforms to shape of beaker for even application of heat Controller…

User friendly microprocessor-based ramping control Microprocessor based PID control Ramp-rate or time-based programming profiles 24 Step program capability Program looping Guaranteed soak (dwell) deviation Auto tuning function allows automatic setting of control…

These funnel mantles allow extraction of fluids while hot, preventing solidification of viscous material in cold stopcocks. The thickness of the fiberglass fabric between heating elements and soft glass wall of the separatory funnel prevents thermal strain and the resultant cracking. Viewing is…

The Buchner funnel mantle provides convenient support for funnel and gentle heat for solutions that must be kept warm during transfer. Durable support bracket slides over mast of ring stand, enabling mantle to be positioned at any convenient height above receiver.

Each separatory funnel holder will hold one funnel, and you can use up to four holders, which mount to the platform without fasteners. While the rear support of the funnel holder remains stationary, the front part holding the funnel can be released and rotated 360°. This permits the funnel…

Takes one test tube rack containing capped or stoppered tubes from 75 to 200 mm long Use existing test tube racks up to 12" x 5" (305 x 127 mm) Rack is secured in holder by lid which fits over threaded end posts and is adjustable in height above support platform. Knurled nuts are used…