For flasks, resin kettles, etc. Constructed of aluminum exterior for extreme durability Form fitting for even heat distribution Internal operating temperature limit of 450°C. Usable with a splash guard or poncho shield for increased safety and life. Certified by Canadian…

The ideal, no-hassle way to prevent unwanted heat transfer in the lab Three different InsulEze kits can be used alone or in combination to insulate almost any laboratory configuration Can be used as a heat shield, a cold shield, for insulating over heaters, as a shock absorber, as a…

Mixes multiple samples for better reproducibility Variable speed range: 100 to 2000 RPM Pulsing feature interrupts vortexing to join upper and lower strata for more thorough mixing DC motor with filter control for smoother operation and longer life Set speed and pulsing to identical time for…

Designed to meet mixing requirements for varying viscosities and volumes Feedback circuitry to maintain speed when viscosity changes Reference circuitry to maintain speed even with voltage fluctuations of ±10% Cord connections between drive motors and controls Stirrers filter the drive…

Nutating Separatory Funnel 3D Shaker Our nutating shakers combine the functionalities of a vigorous laboratory shaker with an added circular rocking motion. The result is that samples are shaken while also being oscillated around a central axis - this means that agitation of the…

Heating Mantles/Stirrers in Self-Standing Metal Case Eliminates need for mantles with holes or very thin insulation that will accommodate separate stirring devices The optional EMC-4 StirControl II (Thomas number 5912M10) creates and synchronizes a rotating magnetic field within the StirMantle…

The centrifuge tube holder allows shaking vertically to let gases escape, or horizontally with stoppers secured by a plate. Each holder accommodates up to eight 15 mL glass tubes of up to 16 mm diameter, 126-160 mm long (stoppered) Up to 2 holders can be shaken at once Load Capacity:…

The centrifuge tube holder allows shaking vertically to let gases escape, or horizontally with stoppers secured by a plate. Holder accommodates up to eight 50 mL glass centrifuge tubes and test tubes up to 28 mm diameter, 140-180 mm long (stoppered) Up to 2 holders can be shaken at once …

This mantle helps prevent vapor condensation in the upper half of a flask during distillation of high-boiling materials. The tops are designed for use with Series M, TM, or STM mantles. They protect the flask, the solutions, and the laboratory from drafts, which would disturb the reflux ration…

Variable speed control Compact size Heavy duty Fuse protected Smaller size makes this ideal for use on a lab bench; in small incubations, refrigerators, biological cabinets and fume hoods; or in any other area where space is limited. Specifically designed to handle both large…

Takes one test tube rack containing capped or stoppered tubes from 75 to 200 mm long Use existing test tube racks up to 12" x 5" (305 x 127 mm) Rack is secured in holder by lid which fits over threaded end posts and is adjustable in height above support platform. Knurled nuts are used…

The extension support attached to a stable ring stand or distillation rack can be adjusted to any convenient height. Extension supports should be used with smaller aluminum housed heating mantles. Steel ring construction with a 6" shank

Smooth rotation and repeatability Totally enclosed motors Variable speed motor drives are designed to make the homogenizing process faster, safer and more thorough. These variable-speed drives feature totally enclosed motors. For high-speed operations, the direct drive shaft is…

Thorough mixing action Variable speed control Speed range of 2-80 rpm Dry Powder Rotator has the drive bar set at a 20° angle so the motion of the rotator closely reproduces the mixing action achieved when mixing by hand, making it useful for working with hard-to-mix powders. Not only is the…

VentSep, a special 1000 mL separatory funnel with a built-in relief valve, can be used on Glas-Col's Bench-top Shaker or either of the Glas-Col 3D shakers. These separatory funnels feature a built-in relief valve Funnels have a fluoropolymer resin stopcock, and a screw cap with…

Provides automatic, time-proportioning control of temperature for loads of up to 1,200 watts Temperature range 0-500°C (0-1,000°F) Used with heating mantles, tapes, cords, small ovens and other resistive heating loads Controller has a calibrated set-point dial in °C and…

Controls two separate circuits independently Provides precise manual control of heating mantles, tapes, cords and other resistive loads Adjustable output range from 3-100% of rated voltage Use on bench top or mount to lattice work using clamp provided on back panel Will…

Use with heating mantles, tapes, cords, small ovens and other resistive heating loads Digital dual output display for set point and process temperature indication Automatic tuning for accuracy with minimum overshoot Auto cold junction compensation and thermocouple break protection …

This mantle can accomodate and efficiently heat all types of straight walled metal beakers by preventing contact of heating elements and vessel walls with inner layers of glass fabric. Also available for glass beakers with resilient and pliable interior glass fabric which cradles fragile beakers.…

Power Drive Unit, Rotator For continuous rotation of accessory head at speeds of 2 to 60 rpm Variable speed control adjusts speed from gentle mixing to rapid agitation Suitable for rotating tissue culture specimens or blood cell suspensions without sedimentation or foaming …

Each separatory funnel holder will hold one funnel, and you can use up to four holders, which mount to the platform without fasteners. While the rear support of the funnel holder remains stationary, the front part holding the funnel can be released and rotated 360°. This permits the funnel…

Shakes two flasks simultaneously Operates in cold room or incubator Secures glassware up to 3 1/2” in diameter The WS 180 shaker efficiently agitates small to medium solid phase peptide synthesis flasks. It is also useful for shaking culture flasks and for agitating hard-to-dissolve…

For use with 8293Q12 Power Drive Unit Circular aluminum rack that holds up to 108 mini tissue culture tubes, up to 16 mm in diameter Rack, 305 mm diameter

This mantle's even heat distribution prevents scorching of clear resinous materials. It's one-circuit heat input simplifies temperature control. Resin flask mantles, as well as most other Series O mantles, are available modified to accept vessel drains or other tubulations.

Stirrer Shafts, with 4-Blade Propeller Shaft diameter 6.4 mm, with stainless steel, 4-blade propeller on one end Listings show shaft length x propeller diameter Stirrer Shaft, with 3-Blade Propeller 8 mm-diameter shaft has stainless steel propeller and includes coupling Shaft length 222…