Chromatographic column with 24/40 standard taper joint at top and 2mm bore 1:5 taper solid PTFE stopcock plug at bottom. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring, and 5853-07 Tubing Connector for connecting 12.5 to 14mm…

Simple absorption column for rapid preparative separations with moderate resolution. Modified with a #25 Ace-Thred connector in place of 35/20 joints, for grease free connection. Internally threaded connector & Nylon bushing make a pressure-tight, O-Ring compression seal with glass stem on…

Plain, open top, chromatographic column, with porosity B (70 - 100 m) fritted disc sealed in.

Used in ASTM D1319-65T, a "test for hydrocarbon types in liquid petroleum products." This unit is fabricated from ACE Trubore tubing. Tip is attached to column by means of a 12/2 spherical joint. Upper joint spherical 28/12.

Chromatographic column with 2mm bore 1:5 taper solid PTFE stopcock plug at bottom.

Rapid preparative chromatography system suitable for use to pressures of 50 psig, operation behind a shield is recommended. Resevoir is 2L or 3L capacity, epoxy coated and pressure tested. Complete item includes:Brass or glass manifold, pressure gauge, pressure relief valve, column, tubing, and…

Chromatographic column with integral reservoir for connecting 5872 Flow Control Adapter. With 2mm bore, 1:5 taper solid PTFE stopcock plug at bottom. Available with or without porosity B (70 - 100 m) fritted disc sealed in. Order column, flow control adapter and clamp separately.

Simple absorption chromatography column for rapid preparative separations with moderate resolution. Allows separations of samples from 0.01 to 10.0g3 in 10-15 minutes. Column and reservoir, only, are Epoxy Coated. Reservoir connects between column and flow control adap-ter. Joints on column,…

Injection reservoir bulb with Ace-Thred ends. 250mL to 3000mL sizes.

Chromatographic column with integral reservoir and #15 Ace-Thred at top, and 2mm bore 1:5 taper PTFE plug at bottom. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring, and 5853-07 Tubing Connector for connecting 12.5 to 14mm O.D.…

Drip tip for chemical type chromatography with 1:5 taper PTFE stopcock at bottom for controlling flow.

Designed for metal recovery using Ion-Exchange resins such as Amborane. Borosilicate glass column has #25 Ace-Thred at both ends. Polypropylene end fittings form a leak-tight seal with FETFE O-Rings. Fittings have 1/4" npt female thread for connecting 3/8" O.D. flexible vinyl tubing from…

High performance, non-packed, low pressure liquid chromatography columns, epoxy-coated. Simple to assemble, PTFE (no O-rings), safe operation to 150psi with safety shield. Usable with various packing materials chemically inert, zero dead volume, leak free. For analytical or preparative…

Plain, open top, chromatographic column, universally suitable for many separations.

Chromatographic column with 2mm bore, 1:5 taper solid PTFE stopcock plug and porosity B (70 - 100 m) fritted disc sealed in.

Chromatographic column with 24/40 joint at top, 2 mm bore 1:5 taper solid PTFE stopcock plug at bottom and porosity B (70 - 100 m) fritted disc sealed near bottom of tube. These columns also appear in expanded listing under 5871.

Acrylic safety shield and polyethylene cap for use with Michel-Miller Columns to insure safe operation at pressures to 300 psi. Top thread of column is hung in polyethylene cap; cap is then held by the plastic shield. Clamp the shield, not the column.

Simple absorption chromatography column for rapid preparative separations with moderate resolution. Allows separations of samples from 0.01 to 10.0g in 10-15 minutes. Column and reservoir, only, are Epoxy Coated. Reservoir connects between column and flow control adap-ter. Joints on column,…

For charging columns. The capacity is approximately 5 times the largest column volume. Size listed is Ace-thred designation which refers to I.D. of tubing above thread and corresponds to 5820 column dia- meter. Available in cylindrical or conical shapes.

Column has standard taper 24/40 joint at top and 2 mm bore stopcock at the bottom with Por. B (70-100m) fritted disc sealed into the bottom of tube.

Columns are fully jacketed including internally threaded ends for circulation of heat exchange media. A wide choice of upper and lower end pieces can be fitted to columns using 5837, 5838, 5840, 5841, 5842 and 5843 fittings. Available in variety of diameters and lengths. Not for use with 5819 fittings.

Chromatography accessory pre-column and injection reservoirs.

Chromatographic column with integral reservoir at top, and 2 mm bore 1:5 taper PTFE stopcock plug at bottom. Opening at top is either 24/40 outer joint or opening for #3 stopper. Available with or without porosity B (70-100micron), fritted disc sealed in.

Rugged columns with internally threaded ends to which a wide choice of upper and lower end pieces can be fitted using 5837, 5838, 5841, 5842, and 5843 fittings. Available in a variety of lengths and diameters. Some sizes available with epoxy coating for added protection against scratches.

Chromatographic column with 2mm bore, 1:5 taper solid PTFE stopcock plug and porosity B (70 - 100 m) fritted disc sealed in at bottom and #15 Ace-Thred at top of column. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring and 5853-07…

Drip tip for chemical type chromatography. I.D. of drip approximately 4 mm. Size listed is Ace-Thred designation which refers to I.D. of tubing above thread and corresponds to 5820 column diameter.

Used in ASTM D1319-65T, a "test for hydrocarbon types in liquid petroleum products." Consists of a charger section with a capillary neck, a separator section, and an analyzer section. Upper joint spherical 28/12.

Chromatographic column with #15 Ace-Thred at top and 2mm bore 1:5 taper solid PTFE stopcock plug at bottom. Column supplied with 7506-06 Nylon bushing and FETFE O-Ring. Complete item consists of column with bushing and O-Ring, and 5853-07 Tubing Connector for connecting 12.5 to 14mm O.D. tubing to column.