Kemtech America Glass Joints & Adapters
-
SYNTHWARE Glass Check Valves
Kemtech AmericaCheck Valve, All Glass, Synthware, Hose Connections OD: 8mm, with ground seat for liquid seal.
-
Synthware Vacuum Filtration Adapters
Kemtech AmericaUsed with plain stem Buchner funnels and pluro-stopper. Hose connector has an O.D. of 10mm at the largest serration. Joint is a standard taper inner joint. Pluro-stoppers are not included.
-
SYNTHWARE Microscale Vigreux Distilling Heads
Kemtech AmericaWith Vigreux Indentations, used with 25mm immersion thermometer, and D27 distillation receiver.
-
SYNTHWARE Solvent Still Head, High Vacuum Valves
Kemtech AmericaSolvent Still Head, High Vacuum Valves Capacity: 250mL Joints: 24/40 Valve Size: 0-4mm
-
SYNTHWARE Cow-Type Distilling Receivers with Hose Connection
Kemtech AmericaCow-type design having three receivers spaced 40° apart. 105° angle between top outer joint and lower inner joins.
-
Synthware Distillation Adapters with Threaded Thermometer Ports
Kemtech AmericaSynthware distillation adapter with threaded thermometer port. The threaded port will accommodate a 6-7.5mm O.D. plain thermometer. The adapter has standard taper top outer joint and inner joints for the bottom and side. All joints are the same size.
-
SYNTHWARE Shortpath Distilling Head for Volatile Distillants
Kemtech AmericaWith the condenser being a combination of a cold coil and Leibig. Top outer joint is a 10/18 for use with a 50mm immersion thermometer. With Vigreux Indentations.
-
SYNTHWARE Solvent Still Head
Kemtech AmericaSolvent Still Head Capacity: 500 and 1000mL available Top Joint: 24/40 Bottom Joint: 24/40 Side Joint: 14/20
-
Synthware Flushing Adapters
Kemtech AmericaSynthware flushing adapter is used to flush and fill attached vessels with an inert gas to provide protective storage. A ballon is connected to the top hose connection. An inert gas is connected to the side hose connection. The ballon can be expanded with inert gas at the same time as the vessel or…
-
Synthware Inlet Adapters
Kemtech AmericaSynthware inlet adapter with a standard taper inner joint. Design allows introduction of reactants below the surface. The serrated hose connections have an O.D. of 10 mm.
-
SYNTHWARE Hickman Still Head, with Side Port
Kemtech AmericaHickman Still Head, with Side Port, Synthware, Joint: 14/10, for microscale fractional distillation, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
-
SYNTHWARE Snyder Distillation Column
Kemtech AmericaSnyder Distillation Column, 3 Section Top Outer Joint: 24/40 Lower Inner Joint: 24/40 Column Height: 150mm Overall Height: 300mm For use with Kuderna-Danish flask.
-
Kjeldahl Trap Adapters
Kemtech AmericaSynthware distillation adapter with Kjeldahl trap. With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is approximately 200mm.
-
Synthware Claisen Adapters, Modified
Kemtech AmericaIt is modified with an additional side arm at 45 degrees to the vertical outer joint. All joints are the same size.
-
Synthware Inlet Adapters with Hose Connection
Kemtech AmericaAdapter has a Nylon compression cap and a Viton o-ring to form a vacuum tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. The 8mm hose connection can be used for N2/Ar introduction or vacuum. Supplied with one Nylon cap and one Viton o-ring.
-
SYNTHWARE Inlet Connecting Adapter
Kemtech AmericaInlet Connecting Adapter, High Vacuum Valve Joint: #15 O-ring Valve Size: 0-4mm Side Port: 10mm OD.
-
Synthware Distillation Adapters, 75°
Kemtech AmericaSynthware distillation adapter bent at 75 degrees. Both ends are standard taper inner joints and are the same size.
-
SYNTHWARE Peptide Synthesis Vessels, Solid Phase
Kemtech AmericaPeptide Synthesis Vessel, Solid Phase, Synthware, Capacity: Available in sizes ranging from 10-50mL, Frit Porosity: Coarse or Medium, Frit Diameter: Available in sizes ranging from 15-25mm, GL Thread: 14 or 25 available, Arm OD: 8mm, Supplied with a PTFE lined cap and straight bore PTFE stopcock…
-
Synthware Inlet Adapters
Kemtech AmericaFor use with gas inlet tubes or plain stem thermometers. Supplied with one holed rubber adapter.
-
Synthware Thermometer Adapters
Kemtech AmericaSynthware thermometer adapter with a 5 degree offset and a serrated hose connection for vacuum. Joints are standard taper.
-
Synthware Vacuum Take-Off Adapters
Kemtech AmericaSynthware vacuum take-off adapter with drip tip. The upper outer and lower inner standard taper joints are the same size.
-
SYNTHWARE Vacuum Jacketed Distilling Heads
Kemtech AmericaDistilling Head, Vacuum Jacketed Thermometer Joint: 10/18 Joints: 14/20 or 19/22 available For use with 25mm immersion thermometer.
-
Synthware Distillation Adapters
Kemtech AmericaAdapter is bent 105 degrees. The top outer and lower inner standard taper joints are the same size.
-
SYNTHWARE Distilling Receivers with Tubes
Kemtech AmericaSupplied with distribution adapter, three 12mL receiver tubes and three plastic joint clip. With 135° angle between top outer joint and lower inner joint.
-
Synthware Bushing Adapters
Kemtech AmericaSynthware bushing adapters allow for compact assemblies of dissimilar standard taper joints.
-
SYNTHWARE Distilling Heads for 76mm Thermometers
Kemtech AmericaThermometer joint is 10/18 for 76mm immersion thermometer. Side arm is at 75° angle.
-
Synthware Distilling Adapters, 105°
Kemtech AmericaSynthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints.
-
Synthware Rotary Evaporator Anti-Splash Traps with Fritted Discs
Kemtech AmericaSynthware rotary evporator anti-splash trap with extra coarse fritted disc. Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. the frit reducesfoam from being carryover. With upper outer and lower inner standard taper joints.
-
Synthware Vacuum Adapters with Outer Joints & Glass Stopcocks
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper outer joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
SYNTHWARE Short Path Vacuum Jacketed Distillation Apparatus
Kemtech AmericaVacuum jacketed design for more efficiency. When a thermometer is inserted in the top of this apparatus, the bulb and stem serve as column packing. The close coupled condenser and vacuum connection offer and extremely short condensate travel path. Used with 25mm immersion thermometer, and D27…
-
Synthware Kjeldahl Distilling Trap Adapters
Kemtech AmericaAdapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.
-
SYNTHWARE PTFE Joint Sleeves
Kemtech AmericaJoint Sleeve, PTFE, Ribbed with gripping ring, Synthware, Sizes available to fit various joint sizes.