Vacuum Pump Trap

Compare Tool

Select up to 3 products

Vacuum Pump Trap
1 - 32 of 89
Sort
View
Show
  • Vacuum Pump

    Dynalon

    …(l x w x h) : 9.5x3.125x1.375in For generating vacuum and extracting liquids and vapors*. Designed for excellent performance: Very low water consumption, constant ultimate pressure and high suction capacity . Pump fluid: water Overall length: approximately 210 mm (R 3/4''…

  • Vacuum trap system protects gauge heads, like our 14034, and pumps from corrosive vapors and particle fouling. System consists of a Dewar flask, cold trap and inlet arm. High-vacuum stopcocks are used throughout. Gauge & inlet arm are Ace-Thred connections. Pump & manifold connections are o-ring…

  • …Rotavapor® R-100. The ready to use vacuum pump will be delivered with a silencer and 2m of vacuum tubing. All Models Capacity, Final Vacuum 1.5 m3/h, 10 mbar 1190U86 Condensation assembly: Secondary cold trap Vacuum Controller: I-100 (Manual, Timer) Woulff…

  • SYNTHWARE Vacuum Trap

    Kemtech America

    For use with vacuum manifolds having 35/20 socket joints. Please order the pump adapter and socket clamp separately.

  • Vacuum Trap Size 21

    DWK Life Sciences (Kimble)

    Connections are 180º apart for easy installation into a variety of vacuum systems. Protects the mechanical pump from attack by corrosive vapors which can be condensed by using liquid nitrogen or dry ice/slurry mixtures.

  • …and pump life. Large oil reservoir minimizes contaminant effects to maintain high vacuum performance. Use of a cold trap is recommended to protect the pump and enhance vacuum levels. Do not operate continuously at pressures greater than 10 torr. DuoSeal two stage pumps provide deep vacuum (1 X…

  • Vacuum Trap Com Size 21

    DWK Life Sciences (Kimble)

    Outlets are 180º apart for easy installation into a variety of vacuum systems. Protects the mechanical pump from attack by corrosive vapors which can be condensed by using liquid nitrogen or dry ice/slurry mixtures. Two-piece construction allows removal of condensate.

  • …after the pump. 1230D90 - Secondary Condenser Vaccum Pump V-700/710 compact high performance condenser for producing maximum condensation of residual solvent vapor after the pump. 1230D91 - Secondary Cold Trap, If dry ice is used instead of cooling water, a suitable cold trap can also…

  • …the pump. 1230D90 - Secondary Condenser Vaccum Pump V-700/710 compact high performance condenser for producing maximum condensation of residual solvent vapor after the pump. 1230D91 - Secondary Cold Trap, If dry ice is used instead of cooling water, a suitable cold trap can also…

  • …contaminants in pump oil. 1169A97: Outlet Oil Mist Separator Outlet oil separator removes oil particles from exhaust stream, minimizing oil loss to atmosphere. 1169A98: Oil Mist Filter Use oil mist filter on CRVpro4, CRVpro6, and CRVpro8. Oil mist filter traps oil before it's…

  • Laboratory High Vacuum Pump

    Fischer Technical

    …from vacuum system          Trap:     Reduces risk of oil sucked back into the system This direct drive pump provides the best Performance/Cost Ratio available today. Comes complete with initial supply of High Vacuum Pump Oil. …

  • …returns trapped pump oil back to the pump and makes pumps much quieter to run. Comes with one replaceable filter element (installed), one KF25 clamp and one centering ring. SMF-020: EZ-Swap Large Capacity Pump Exhaust Oil Mist Filter w/ Fittings Our EZ-Swap large capacity series vacuum pump

  • Protect vacuum pumps from foreign materials by ensuring the highest quality air is entering the pump Plastic transparent sump shows when to change filter insert Simple to maintain-change filter inserts without removing trap from vacuum system 4.5 inch trap serves vacuum pumps up to…

  • Pumps that use oil either as their working fluid (diffusion pumps), or as their lubricant (mechanical rotary pumps), are often the sources of contamination in vacuum systems. Placing a cold trap at the mouth of such a pump greatly lowers the risk that oil vapors will back stream into the vacuum

  • …that allow the trap to hang on the side of the RapidVap Vacuum System. Alternatively, the bracket serves as a stand to stabilize the glass container resting on a flat work surface. This trap may also be used with pre-2005 CentriVap Cold Traps. Liquid Trap prevents liquid from entering the pump.

  • …placed between the main and pre-trap to permit connection of vacuum measurement device via a AF-0306-01 thermocouple adapter. Both traps can be isolated from the manifold or pump via 0-12mm Chem-Vac™; Chem-Cap®; valves (H). Trap assembly is designed to allow connection to either the right…

  • Hydrocarbon Trap

    PerkinElmer

    New Hydrocarbon Trap - great for LCMS nitrogen units and GC units with 1.5 times the capacity of our current N9301192 High Capacity Hydrocarbon Trap - N9301192 Contains 750cc of preconditioned activated charcoal. Stainless Steel bdy. 1/4" brass compression fittings with ferrules for…

  • …PTFE pump. All wettable parts, including the diaphragm and valves are PTFE. Vacuum level regulator and built-in dial guage allow easy control of pressure to prevent sample bumping or foaming. Switchable gas ballast inhibits vapor condensation inside pump heads. An inlet separator traps ejected…

  • Compact, convenient Deep vacuum Use these Welch 2-stage direct drive pumps for a wide range of laboratory applications to provide deep vacuum down to 1 x 10-4 torr. Common lab processes include freeze drying, vacuum oven drying, glove box vacuum, centrifugal concentrator operation, and…

  • 1229D81 - Buchi V-850/855 Vacuum Controller Valve combined with condensate trap and non-return valve with attachment for Rotavapor (not necessary with V-700/710 in stand-alone systems). 1229D82 - Buchi RC-81 remote control can be used to control the vacuum controller and the Rotavapor:…

  • …cooler running and longer service life. ChemStar pumps rotate at speeds less than 580 RPM, compared with over 1700 RPM of direct-drive vacuum pumps. Dry Nitrogen Purge both degasses and cools the pump oil reducing the corrosion rate in the pump. Accessories (available on special order): Protective…

  • vacuum pumps are piston powered, so they do not pollute the air and require minimal maintenance Quiet, low-vibration units keep disturbances to a minimum Built-in thermal protector automatically shuts off pump if it overheats and then restarts it once the unit is cool Inlet filter traps

  • Complete Vacuum Traps with 3/8" Hose Connections

    Wilmad-LabGlass - SP Scienceware

    Widely used to protect vacuum pumps from contamination, these borosilicate glass vacuum traps are a one piece unit with two 3/8" hose connectors. Connectors are 180° apart to ease connection of heavy wall rubber tubing used in basic vacuum set-ups. These traps are frequently used with…

  • …KNF vacuum pump and the laboratory device, this trap improves solvent recovery, pump reliability, eliminates downtime by preventing excessive liquid condensate from reaching the pump, and reduces the amount 057953 The KNF Woulfe bottle is a combination vacuum regulator and trap. Offered…

  • Ai EasyVac Dual-Stage Vacuum Pumps

    Across International

    …9 CFM vacuum pump is now 110V/220V 50/60Hz switchable! Ai EV9 are dual-stage high speed sliding-vane rotary compact vacuum pump with KF25 vacuum connector. Comes with all necessary fittings and a exhaust oil mist filter which also returns trapped pump oil back to the pump and makes the pump

  • Ai EasyVac Compact Vacuum Pumps

    Across International

    …sliding-vane rotary compact vacuum pump with 3/8" hose barb vacuum connector. Comes with a 3-foot food grade silicone hose and a exhaust oil mist filter which also returns trapped pump oil back to the pump and makes the pump quieter to run. It is important to note that pumps should always be…

  • The CentriVap Cold Trap collects evaporated liquid from a CentriVap Concentrator, protecting an accessory vacuum pump from the corrosive effects of vapors and fumes emitted from samples. Exclusive features include: brushed, stainless steel and glacier white, epoxy-coated steel exterior with blue…

  • Aspirator with Trap Flask

    Grant Instruments

    The aspirator with trap flask FTA-1 with a 1L trap flask is designed for the aspiration or removal of any remaining alcohol or buffer from microtest tube walls during DNA / RNA purification and other macromolecule re-precipitation techniques. An ideal personal tool for independent operation…

  • …bottle Vacuum Pump: V-100, 1.5 m3/h, 10 mbar 1190U73 Glass Assembly: C (Cold trap) for low boiling point solvents Protective Coating: Without Recirculating Chiller: F-100, fix +10 °C, 400 W Vacuum Controller: I-100, with Woulff bottle Vacuum Pump: V-100, 1.5…

  • …handle and tubing are autoclavable. With 2-wire cord and plug. Pipet-Aid with Filter Trap Similar to 7775L10 and L12, but with filter unit in the vacuum line between filler handle and pump to trap hazardous aerosols. Includes 2-wire cord and plug. Pipet-Aid Filter Adapter Kit …

  • Air Pump

    Gast

    …operation Free air displacement 1.3 cfm (37 Lpm) Stainless steel pump valves; aluminum cylinder and piston parts Equipped with safety pressure relief valve, intake filter and moisture trap, vacuum and pressure gauges, serrated tubing connector on inlet and outlet and carrying…

  • Cascade Dry Ice Trap

    Cascade Sciences LLC

    …this “ice bucket” style cold trap. Fill the internal stainless steel reservoir with a cold slurry mix of ice/ alcohol/ dry ice and set inside the larger steel vessel. The cold surface of the trap attracts and condenses material that would otherwise be ingested by the vacuum pump.

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.