Vacuum Adapter

Compare Tool

Select up to 3 products

Vacuum Adapter
1 - 32 of 322
Sort
View
Show

  • Synthware vacuum adapter with a serrated hose connection 180 degrees to the standard taper inner joint. The PTFE stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Synthware vacuum adapter has a standard taper outer joint and a serrated hose connection. Ideal for use as a vent or for the introduction of pressure/vacuum.

  • With standard taper top outer and lower inner joints with sealed in drip tip. Adapter is bent at a 105° angle for use in vacuum distillation. Serrated hose connection has an O.D. of 10mm at the largest serration for connection to vacuum source.

  • Synthware vacuum transfer adapter with PTFE stopcocks and standard taper inner joint. Used for the transfer of sensitive and hazardous solutions while under vacuum.

  • Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Thomas No. 1165A11 14/20 vacuum adapter, 30mm stem below the joint. Thomas No. 1165A12 14/20 vacuum adapter, 175mm stem below the joint. Thomas No. 1165A13 19/22 vacuum adapter, 30mm stem below the joint.

  • Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the standard taper inner joint.

  • Adapter used for reduced pressure filtration with plain stem buchner funnels. Top is flared to accept the listed size pluro stopper. The hose connection has an O.D. of 10mm at the largest serration. ADAPTER IS NOT SUPPLIED WITH RUBBER PLURO STOPPER, See CG-1401.

  • With standard taper top outer and lower inner joints with sealed in drip tip. Serrated hose connection has an O.D. of 10mm at the largest serration for connection to vacuum source.

  • …non-pyrogenic & gamma irradiated Filtration tops fit on 45mm neck bottles 45mm neck size The Denville 250ml, 500ml and 1000ml Vacuum Filtration Flasks are ideal for separation and purification of your samples. Membrane material includes PES and PVDF in .22µm and .45µm.…

  • Useful as a vacuum adapter or addition tube. Stem length below joint, 130MM. Hose connection is Size A for 5/16th I.D. tubing.

  • Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The PTFE stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Vacuum Adapter, Microscale, PTFE Stopcock, Synthware, Joint: 14/10, Stopcock Bore: 2mm, Hose Connection OD: 8mm.

  • Vacuum Takeoff Adapter, Microscale, Synthware, Joint: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.

  • Glass Vacuum Adapters

    United Scientific Supplies

    Vacuum adapters have 24/40 joints. Bent adapter has a 105° angle between the top outer joint and bottom inner joint. Straight adapter has a top outer joint and bottom inner joint. Both adapters have 24/40 joints and include a 3/8" hose connector.

  • Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper outer joint. The PTFE stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Adapter, Vacuum

    Ace Glass

    With side hose connection and drip tip.

  • …filtration system. Each filtration unit includes a sterile centrifuge tube and cap, 50ml funnel with PES membrane, funnel adapter (for the 15ml tube assembly), vacuum hose adapter, and dual centrifuge tube stand. The Autofil® Centrifuge Funnel system is used for sterilization of tissue cultures…

  • Synthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper outer joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Synthware vacuum adapter with 2mm straight bore PTFE stopcock on the hose connection.The upper outer and lower inner standard taper joints are the same size.

  • Synthware vacuum take-off adapter with drip tip. The upper outer and lower inner standard taper joints are the same size. 

  • Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. 

  • Adapter Vacuum ST 24/40

    DWK Life Sciences (Kimble)

    Vertical adapter with vacuum take-off and drip tip.

  • Synthware vacuum take-off adapter with drip tip. For use in vacuum distillation. Adapter is bent at 105 degrees. Serrated hose connection is attached to vacuum source. With standard taper top outer joint and lower inner joint of the same size.

  • VitroKit

    DWK Life Sciences (Wheaton)

    …to seize and do not require lubrication Kit contains following assortment: Claisen adapter; connecting adapter; thermometer adapter with Neoprene bushing; vacuum distilling adapter; 200 mm West condenser; 200 mm distilling column; 125 mL separatory funnel with Teflon ® stopcock…

  • Adapter, Vacuum

    Ace Glass

    With 14/20 or 19/22 joints, outer joint at top and inner at bottom. Size B hose connection is on side.

  • Synthware vacuum adapter with a serrated hose connection 180 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.

  • Used with plain stem Buchner funnels and pluro-stopper. Hose connector has an O.D. of 10mm at the largest serration. Joint is a standard taper inner joint. Pluro-stoppers are not included.

  • With two standard taper inner joints that are parallel and at a 75 degree angle to the connecting tube. Distance between joints is 100mm.

  • PTFE connecting adapters and glass conversion adapters for connecting GPI threaded vials to a rotary evaporator vapor tube or trap. Both are suitable for vacuum work. PTFE connecting adapters are available with FETFE or Chemraz o-rings. Order Chemraz if you are using Methylene Chloride or Acetone.…

  • Adapter Vacuum Kem Kit

    DWK Life Sciences (Kimble)

    With a hose connector and a drip tip.

  • Used for reduced pressure filtration with 7186 style, plain stem Buchner funnels. Top is tooled to accept a pluro stopper, bottom has a joint. Serrated hose connection has a second ring of 13.5mm O.D. Inserting the recommended size pluro stopper and th

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.