Solvent Extractor

Compare Tool

Select up to 3 products

Solvent Extractor
1 - 30 of 30
Sort
View
Show
  • …semi-solid samples according to the Randall technique. Beats Ordinary Soxhlet Extractor Up to 5 times faster than traditional Soxhlet (hot solvent vs. cold solvent) Low solvent consumption (high solvent recovery, up to 75%) Limited cost per analysis Convenience &…

  • Gregar Extractor

    Chemglass

    …National Laboratories, this extractor is the only unit on the market that can perform all three common types of extraction. During solid extractions the extractor operates upon the principle of continuous solvent displacement, permitting the sample to be immersed in solvent at all times, thereby…

  • …single piece continuous liquid/liquid extractor is for use with solvents of heavier specific gravity than sample liquid being extracted. It is designed to meet EPA test method requirements outlined by SW-846, RCRA, and CLP. The sidearm is sealed to the extractor body just below the 45/50 Standard…

  • SYNTHWARE Soxlet Extractors

    Kemtech America

    Soxlet Extractor Upper Joint: Available in 34/45, 45/50, and 55/50 Lower Joint: Available 24/40 Used for the extraction of solids with a solvent.

  • Traditional Open Blast Extractor (Comes with 1 yr. Limited warranty, excludes gaskets and screens) The solvent can will fit into the top cap hole Includes: Platinum Cure Silicone Non Stick Pad 304 Stainless Material Tube 304 Stainless Top Cap w/ 3mm Hole (Fits Most Butane…

  • Open Blast Extractors

    Best Value Vacs

    Traditional Open Blast Extractor (Comes with 1 yr. Limited warranty, excludes gaskets and screens) The solvent can will fit into the top cap hole (Rated to 500psi, Working pressure will only reach 20 PSI when using solvent cans) Sanitary Grade 304 Stainless Steel Tube Fittings 150 Micron…

  • Mini Closed Loop Extractors

    Best Value Vacs

    … Weight: 18 lbs. Operating Temperature Range: -40°F to 160°F Ultimate Vacuum: as low as 10 Microns Designed to run a single can of solvent and reclaim it (350ml) Max FILL!! Construction: All components made of 304 Stainless Steel Max Vacuum -29.9inHg High Polish Interior

  • The ROT-X-TRACT-S® rotary Soxhlet extractor can accommodate up to 8 or 10 Soxhlet extractors. The bath cover disk holes can accommodate round sample flasks from 125 mL to 1 L. A wide range of sample sizes and quantities make this instrument ideal for Soxhlet extraction of samples in any lab. …

  • …allows the organic solvent to circulate through the 1 liter sample bottle continuously until the extraction is complete. By incorporating a stop-cock assembly and 3-ball Snyder column, the Corning One-Step extractor can both extract desired analytes as well as evaporate solvent from the end…

  • …solid with a solvent and then siphoning residues away. Most of the component parts of the various extractor units have Standard Taper joints for quick, secure connections. Extraction thimbles, paper filters or glass wool are used to support the sample. The siphon tube on the extractor is protected…

  • Round bottom design has the return tube sealed into the bottom of the extractor for more efficient extractions. For samples of 1 liter plus approximately 200mL of extracting solvent. Extractor has a 45/50 top outer joint and a 24/40 inner joint on the uptake tube. Flask and condenser must be ordered…

  • Extractor designed for EPA priority pollutant samples where the extracting solvent is heavier than water. For samples of 1 liter plus approximately 200mL of extracting solvent. Extractor has a 45/50 top outer joint and a 24/40 inner joint on the uptake tube. Flask and condenser must be ordered…

  • …a 2mm PTFE stopcock in the return tube. Stopcock stops the flow after the extraction is complete. For samples of 1 liter plus approximately 200mL of extracting solvent. Extractor has a 45/50 top outer joint and a 24/40 inner joint on the uptake tube. Flask and condenser must be ordered separately.

  • …type extraction apparatus used for continuous extraction of solids with a suitable solvent. Extractor uses paper or CG-1372 glass thimbles. Condenser has an enlarged uptake tube to improve condensing capacity. Complete apparatus consists of an Allihn condenser, extractor and flat bottom flask.

  • …reduces from 36 hours to 12 hours.  Extraction process requires only 100 mL of solvent versus 500 mL , an 80% reduction. This reduces solvent emissions (solvent recovery is built in), solvent cost, and solvent disposal. No separate extract drying required due to use of a hydrophobic membrane.…

  • …2L Extractors (with 2L, 3L, and 5L flasks, respectively) are supplied with improved Double Surface Condensers, for ultimate cooling and solvent retention. Borosil® Complete Soxhlet Extractors allow for extraction of non-volatile compounds from a sample by way of continuous reflux solvent

  • Soxhlet Extraction Apparatus

    SP Wilmad-LabGlass

    solvent. Units are supplied complete with flat bottom boiling flask, Soxhlet extractor and Allihn condenser. The extractor capacity shown is the solvent volume held in the extractor to the top of the siphon tube. The siphon tube is protected from accidental damage by the vapor tube. Extractor has…

  • solvent. Complete units are supplied with a round bottom boiling flask (LG-7220-184 or LG-7220-188), a Soxhlet extraction tube (70mm or 100mm approx. I.D.) and an Allihn condenser. The extractor capacity is the solvent volume held in the extractor to the top of the siphon tube. The extractor has a…

  • …using Method 625 (base neutrals/acid extractables). Accommodates 1L sample and approximately 200mL of a heavier-than-water extracting solvent. Features an extractor body designed to accept a common condenser with a 45/50 joint, a 24/40 opening with a PTFE stopper near top of body for addition of…

  • A liquid-liquid extractor for use with lighter or heavier-than-water extracting solvents. Overflow and boil-up tube uses Ace-Thred Connections, thus allowing easy removal for cleaning to reduce cross contamination among samples. Complete consists of:Extractor Body, (approx.1.3L capacity), Dispersion…

  • …the separation of individual components from a mixture of solids and semisolids by solvent extraction. The use of a Soxhlet extractor provides a safe method of extraction with toxic or other noxious solvents. Ahlstrom extraction thimbles are recommended for the estimation of fats in food, analysis…

  • For the extraction of soaps, fats, foods, rubber, etc. by both organic and inorganic solvents These thimbles offer the advantages of being rapid, durable and readily cleaned by ignition 4395L15 thimble is used in asphalt extraction apparatus for ASTM Standard D 367; AASHTO T-81; and Barrett tests…

  • Extract-All Compact Air Cleaning System

    Air Impurities Removal Systems, Inc.

    …heavy duty extractor arms Easy access enables fast change of filters Captures and removes contaminants at the source by collecting and filtering smoke, dust and odors. Perfect for use during applications such as: soldering, heat bending, wire stripping, dental grinding, solvents, mixing…

  • 125 ml App, Soxhlet Extraction, Gnd

    DWK Life Sciences (Wheaton)

    …into an organic solvent. As the flask containing the solvent is heated, vapors rise in the larger outside tube, enter the water-cooled condenser, and liquate. When the liquid level in the extractor reaches the top of the bent tube, siphoning action returns the extract-enriched solvent to the flask.…

  • Micro Soxhlet Extraction Apparatus

    DWK Life Sciences (Wheaton)

    solvent WHEATON Connection eliminates the need for hooks, springs and clamps common to standard ground joint designs As the flask containing the solvent is heated, vapors rise in the larger outside tube, enter the water-cooled condenser, and liquate When the liquid level in the extractor

  • …available Soxhlet extractors. Effective when used with solvents incompatible with cellulose materials Resistant to temperatures up to 500°CBinder-free, no chemical additivesDesigned to fit most commercially available Soxhlet extractors.Effective when used with solvents incompatible with cellulose…

  • Presep Glass Prefilters

    GVS Filter Technology

    …Maximum operating temperature is 165°C (325°F). Glass prefilters without binders are designed to avoid binder extractables during solvent filtration or gravimetric analysis. Not recommended for temperatures exceeding 510°C (950°F). For upstream protection of a membrane…

  • …specialized applications. The thimbles are completely free of binders or additives and can be used at temperatures up to 500°C or when using solvents incompatible with cellulose thimbles. These thimbles are also used in pollution monitoring techniques (0.8 µm nominal particle retention).…

  • …specifically for EPA Method 1664A - Oil & Grease (n-Hexane Extractable Material (HEM) in Aqueous Samples). Compatible with Horizon SPE Extractors Obtain faster flow-rates without sacrificing recovery and reproducibility. One-piece 3-layer construction: Top layer - PP pre-filter…

  • …that is inert to a wide range of chemicals. Tedlar is manufactured without plasticizers. Can be used for collecting air containing all common solvents and many other classes of chemicals. Bags with dual stainless steel fittings feature hose/valve and replaceable septa units. Bags with patented…

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.