Pyrex Distiller

60° angle Three Standard Taper 24/40 joints Approximate length 206 mm This tube is also a replacement for organic chemistry kits. Type I, Class A borosilicate conforming to federal specification DD-G-54 lb and ASTM E 438. Also meets the US Pharmacopoeia specs for Type I borosilicate glass.

Suitable for microchemical applications Side-arm on all sizes is approximately 77 mm below the top of the neck at an angle of 75° Adaptable for use with thermometer calibrated for 76 mm immersion 50 mL flask takes rubber stopper No. 1; 250 mL flasks, stopper No. 3; 500 mL flask, stopper No. 4;…

A general purpose batch distillation assembly with the facility for addition via the Standard Taper PYREX® stopped neck Ideally suited for the batch production of high purity distilled water The flask bottom is flat with a slide delivery tube, terminating in a Standard Taper joint …

Connecting 105° angle, two-way,  Standard Taper joints The arms are appraoximately 105° apart One end is equipped with an outer Standard Taper joint and the other end with an inner Standard Taper joint of the same size Used as a receiver adapter 3941S38 is a…

These 25mL PYREX® distilling flasks are suitable for microchemical applications. The sidearm is approximately 77mm below the top of the neck at an angle of 75°. Adaptable for use with thermometers calibrated for 76mm immersion. Flasks take a No. 0 rubber stopper.

This PYREX® cyanide distilling apparatus is used in testing for soluble and insoluble cyanides in water. Cyanide as hydrocyanic acid (HCN) is released from cyanide complexes by means of a reflux-distillation and absorbed in a scrubber containing a sodium hydroxide solution. Tygon® tubing…

These 500mL PYREX(r) distilling flasks are used for the distillation of bituminous materials suitable for road treatment. Also used in the Standard Method of Test of the Distillation of Creosote Oil, American Wood Preservers Association, method 11e, Barrett method C 9, American Association of State…

With outer Standard Taper joint at the top and an inner-sealed through drip-tip joint at the bottom Bent at 105° angle The serrated sidearm is 10 mm O.D. drip-tip at the bottom extends about 20 mm below the lower end of the joint

These PYREX® multiple neck flasks have three vertical side necks with outer Standard Taper joints placed 90° apart and a larger center neck with a vertical Standard Taper joint.

These PYREX® three vertical neck flasks have two side necks with 24/40 outer Standard Taper joints and a center neck with a 24/40 Standard Taper joint. All of the necks are at the same height.

These PYREX® three neck flasks have two angled side necks at the same height with Standard Taper outer joints and a larger center neck with a vertical Standard Taper joint.

These PYREX® three neck flasks have two vertical side necks with full length outer Standard Taper joints and a larger vertical center neck with a full length Standard Taper joint.

This 250mL capacity PYREX® solvent still head is used for maintaining oxygen free solvents. Head has sufficient storage space to allow solvent removal by syringe or drainage through 2mm T-bore PTFE (Polytetrafluorethylene) stopcock. It has a 24/40 Standard Taper outer joint at top, 24/40 Standard…

These 250mL PYREX® three neck flasks have two angled side necks at the same height with 19/22 Standard Taper outer joints and a center neck with a vertical 19/22 Standard Taper joint. This 250mL flask is also a replacement part for organic Material:     Borosilicate Glass…

PYREX®10 mL , Stark- Dean For use in the determination of water in petroleum products and bituminous materials Graduated in 1/10 mL divisions from 0 to 1 mL ; in 1/5 mL divisions from 1 to 10 mL With Standard Taper 24/40 joints; meets ASTM Standard E 123

PYREX® Suitable for storage of distilled water and standard solutions Of borosilicate glass All have heavy, welted neck but vary in size and shape. Bottles take stopper number 12. PYREX bottles are tough and reliable yet designed with safety in mind. PYREX bottles can withstand…

…culture media and sera where stability of the glass is of prime importance. Serum bottles are also suitable for storing distilled water and standard solutions. PYREX bottles have the strength to withstand hot air (dry) or steam (wet) sterilization. Necks are tooled to increase mechanical…

3 to 6 mm in diameter Diameter tolerance is ±0.75 mm PYREX solid glass beads are useful for packing in distillation columns, mixing beads and boiling stones. Beads are packaged in 0.45 kg (1 lb) boxes, which have a packing volume of approximately 360 cm 3 or 22 cubic inches.

Capacity 3 1/2 gallons With 6-mm-bore, Teflon stopcock and overflow tube which takes 1/2” tubing Takes rubber stopper No. 11 1/2 Useful as a delivery/ storage container for solutions. Height 17 3/4”.

Suitable for refluxing, extracting and distilling operations With Standard Taper 24/40 drip tip joint at bottom All sizes take stopper size 3

These 125mL heavy duty PYREX® distilling flasks are suitable for microchemical applications. The sidearm is located approximately 137mm from the bottom of the flask to meet the requirements of ASTM E-1405 and can be used in ASTM tests D-86, D-233 and D-447. Adaptable for use with thermometers…

This specially designed PYREX® cold finger condenser is a replacement part for the PYREX® Cyanide Distilling Apparatus (Thomas No. 0320A91)

This specially designed PYREX® 1L boiling flask is a replacement part for the PYREX® Cyanide Distilling Apparatus (No. 3350-C).

Standard Taper 10/30 thermometer opening, distilling, three-way, Standard Taper joints Sidearm is at an angle approximately 75° from the lower part of the vertical tube The joint on the sidearm is at an angle approximately 105° from the sidearm The sidearm and lower tube are…

These 200mL PYREX® graduated cylinders are calibrated "to contain" (TC) in percent. 200mL is equal to 100% in 1% divisions. The scale is in durable white enamel. This cylinder may be used to measure the distillate in ASTM method D-86 "Distillation of Gas Oil and Similar Distillate…

These 250mL PYREX® atomizers are used for spraying reagents onto thin layer chromatography plates. They have a full length 24/40 Standard Taper joint between the reservoir and spraying device. The PYREX® distilling condenser has 14/20 Standard Taper inner and outer joints, is simple in design and…

The PYREX® distilling condenser has 19/22 Standard Taper inner and outer joints, is simple in design and easy to use. Side tubulations are 10mm O.D. Distilling condensers are widely used in the lab, especially for fractionation. This condenser is also a replacement for organic chemistry kit No.…

This specially designed PYREX® inlet tube is a replacement part for the PYREX® Cyanide Distilling Apparatus (No. 3350-C) Used in testing for soluble and insoluble cyanides in water. Cyanide as hydrocyanic acid (HCN) is released from cyanide complexes by means of a reflux-distillation…

This specially designed PYREX® trap is a replacement part for the PYREX® Cyanide Distilling Apparatus (No. 3350-C) Used in testing for soluble and insoluble cyanides in water. Cyanide as hydrocyanic acid (HCN) is released from cyanide complexes by means of a reflux-distillation and absorbed in a…

These PYREX® connecting distilling tube adapters have full-length inner 24/40 Standard Taper joints of same size. The connecting arm is approximately at a 75° angle from vertical and is 200mm long.

This PYREX® general purpose condenser can be used for either distillation or extraction. Although the condensing area per unit length of the 200mm long jacket is low, the large capacity water jacket gives efficient cooling. Condenser tubulations are approximately 10mm O.D. The adapter end is…

Allihn - suitable for use in vacuum distillations With condensing tube expanded by series of bulbs which increase condensing area and lengthen condensate path Inlet and outlet tubes are on opposite sides of the jacket All sizes take stopper size 3 and have Standard Taper drip tip…