Pyrex Condenser

Available with 200 or 300 mm long heavy-wall outer jackets PYREX® West condensers are designed with a heavy-wall outer jacket to provide a sturdy, long-lasting unit, while the inner tube has a thinner wall for efficient heat transfer. The tubulations are on the same side to reduce breakage.…

Graham Coiled condensing tube is sealed into water jacket Inlet and outlet tubes on opposite sides of jacket With Standard Taper drip tip joint at bottom and Standard Taper outer joint at top The 8” condenser has 19/38 joints; others have Standard Taper 24/40 joints

With Standard Taper 24/40 joints Inlet and outlet tubes, 10 mm o.d. are on opposite sides, indentations at lower end of condenser tube support packing when used as fractionating column.

Suitable for refluxing, extracting and distilling operations With Standard Taper 24/40 drip tip joint at bottom All sizes take stopper size 3

…bulbs which increase condensing area and lengthen condensate path Inlet and outlet tubes are on opposite sides of the jacket All sizes take stopper size 3 and have Standard Taper drip tip joint at bottom and Standard Taper outer joint at top. A widely used condenser with greater surface…

Suitable for the use in vacuum distillations With Standard Taper drip tip joint at bottom and Standard Taper outer joint at top The 8” condenser has Standard Taper 19/38 joints; others have 24/40 joints

This Jacketed Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.

This specially designed PYREX® cold finger condenser is a replacement part for the PYREX® Cyanide Distilling Apparatus (Thomas No. 0320A91)

This Air Reflux Condenser is a replacement part for the 6949M series of PYREX® microchemistry kits.

This PYREX® general purpose condenser can be used for either distillation or extraction. Although the condensing area per unit length of the 200mm long jacket is low, the large capacity water jacket gives efficient cooling. Condenser tubulations are approximately 10mm O.D. The adapter end is…

This simple PYREX® cold finger condenser, of relatively low efficiency, is often used to regulate refluxing by adjusting the flow of air or water through it (dephlegmation). The tubulation O.D. is approximately 10mm. This condenser has a 24/40 inner Standard Taper joint and is a replacement part…

This PYREX® Friedrichs type condenser affords very efficient operation. The helical inner tube fits closely within the jacket. The vapor tube is sealed to the jacket at an angle of 75° and has an outer 24/40 Standard Taper joint.

These PYREX® West condensers are designed with a 190mm long jacket that has a 14/20 Standard Taper top joint. The bottom has 14/20 Standard Taper inner joint with a drip tip. The tubulations are on the same side to reduce breakage. The tubulation O.D. is approximately 10mm. This condenser is a…

These PYREX® condensers have a high surface area per unit length of the 300mm long jacket with a 24/40 Standard Taper outer joint at the top and a plain drip tip at the bottom. They are primarily used in distillation assemblies. Condenser tubulations are approximately 10mm O.D.

These PYREX® condensers have a high surface area per unit length of the 200mm long jacket with a 19/38 Standard Taper outer joint at the top and a plain drip tip at the bottom. They are primarily used in distillation assemblies Condenser tubulations are approximately 10mm O.D.

…strength; the bead also provides a means to equally space the side walls of the bottom and cover, thereby reducing the capillary action of condensed moisture on the sides Dishes are supplied complete with tops and bottoms; the tops are marked in blue enamel and the bottoms in white enamel…

Includes an efficient Friedrichs condenser An efficient extraction apparatus for general purpose use Consists of an extractor, a special Friedrichs condenser and a flask, all equipped with Standard Taper joints Condenser tubulation o.d. is 10 mm for 3/8 inch i.d. tubing

…be used above or near the units in case of a drop in condenser water temperature or loss of condenser cold water supply. Removable Snyder column sidearm allows easy cleaning.  The required concentrator tube (1234B38 or 1234B39) and the Allihn condenser (4406K40) must be purchased separately.

…and spraying device. The PYREX® distilling condenser has 14/20 Standard Taper inner and outer joints, is simple in design and easy to use. Side tubulations are 10mm O.D. Distilling condensers are widely used in the lab, especially for fractionation. This condenser is also a replacement for…

The PYREX® distilling condenser has 19/22 Standard Taper inner and outer joints, is simple in design and easy to use. Side tubulations are 10mm O.D. Distilling condensers are widely used in the lab, especially for fractionation. This condenser is also a replacement for organic chemistry kit No.…

…system be used above or near the units in case of a drop in condenser water temperature or loss of condenser cold water supply. This system comes complete with PYREX® Allihn condenser with a 45/50 Standard Taper inner joint and 500mL PYREX® round bottom boiling flask with 24/40 Standard Taper outer…

This PYREX® solvent recovery head allows for condensation and collection of solvents while performing concentrations with a Kuderna-Danish concentrator. 96-99% solvent recovery allows for concentrations to be done outside the hood. Unique, simple design allows use with existing condensers and…

Condensers have water-jacketed Standard Taper inner joint. Complete with condenser, flask and extraction tube. The low thermal expansion rate means that the PYREX brand extractors can be routinely used in applications requiring protracted heating at temperatures as high as 230°C. The inherent…

…facility for addition via the Standard Taper PYREX® stopped neck Ideally suited for the batch production of high purity distilled water The flask bottom is flat with a slide delivery tube, terminating in a Standard Taper joint Condenser tubulations are 10 mm 500 mL and 1,000 mL…

This is a 1L PYREX® replacement flask with a 29/42 outer Standard Taper joint for the No. 3840-XL 1L extractor system. The tubulation O.D. on the condenser is 10mm.

…flat, clear PYREX® dish bottoms will withstand repeated sterilization (wet or dry). The edges are beaded to provide greater mechanical strength. The bead also provides a means to equally space the side walls of the bottom and cover, thereby reducing the capillary action of the condensed moisture on…

…still combines high performance and reliability with value for money. This new Quickfit® water still features a high quality Pyrex® glass boiler and condenser. Output capacity 4Liters/Hour pyrogen free* single distilled water Easy to install and use Reliable operation - proven…

These PYREX® bombs are for the determination of gum stability of gasoline. The cover prevents condensed vapors in bomb stem from contaminating the sample, but does not interfere with free flow of oxygen. Made in accordance with ASTM D-525.

…continuous liquid-liquid extraction and concentration into one step. A Freidrichs condenser is used to reduce overall height to accommodate traditional laboratory hood specifications; however Allihn condensers can be substituted per request. A hydrophobic membrane allows the organic solvent…

…specific volume needs Features a vertical condenser for maximum efficiency and removal of gaseous impurities Low-water safety protection All Pyrex®, Vycor and Teflon® components Dependable Vycor heating elements; UL and CSA listed Pyrex trap to remove airborne contaminants …

…of the kit or to reorder replacement parts, refer to the specific catalog numbers. -Jacketed Condenser (2405-7). -Jacketed Condenser (2405-14). -Air Reflux Condenser (2850-7). -Air Reflux Condenser (2850-14). -Hickman Still Head (3570-14). -10mL Erlenmeyer Flask (4980-10). -Claisen Head (9055-14).…

Flat, clear PYREX VISTA dishes will withstand repeated sterilization (wet or dry). The edges are beaded to provide greater mechanical strength. The bead also provides a means to equally space the sidewalls of the bottom and cover, thereby reducing the capillary action of the condensed moisture on…