Pycnometer

Gay-Lussac With capillary glass stopper ground to flat-sided point for take-off of overflow 10 mL and 25 mL sizes are for ASTM Standard D 369 and Barrett test H-8; AASHTO standard T-74 *min order of 10 each  

KIMAX® brand, Hubbard-Carmick Used in the determination of specific gravity Conforms to ASTM D 70, D 1963, D 1429 and D 115 for a variety of semi-solid materials and emulsions Conical stopper has 1.6 mm hole to allow air to escape

Thermometer with Standard Taper No. 10/18 ground joint serves as stopper Side arm is fitted with vented 5/12 cap Thermometer range 14° to 37°C in 0.2° divisions; tolerance ±0.2°C Capacities are within 10% of nominal capacities etched on flask 50 mL size…

The BYK-Gardner Weight Per Gallon Cup is a simplified form of pycnometer specially designed to measure the density of a fluid at a standard temperature of 77°F (25°C). The net weight of the air-free sample is determined to the nearest 0.1 gram, and converted by simple factors to either…

A method for measurement of light hydrocarbon liquids as per ASTM D 941. Also Ind. and Eng. Chemistry, Analytical edition, Vol. 16, No. 1, Jan. 1944, page 55.

KIMAX®, Le Chatelier type For the determination of the specific gravity of cement, sand and materials of similar fineness For ASTM Standards E 694 and C 188 Marked with “A” to signify adherence to accuracy specifications in U.S. Department of Commerce publication PB-246 623, The…

Special medium length Ts 10/18 thermometer with a range of 14 to 38°C in 0.2° Accuracy within ±0.2°C Cap for the side tube is Standard Taper 5/12 and has small vent near the top Each flask body is numbered for easy identification The 50 mL size is used to obtain the specific gravity of pigments…

The Thermco pycnometer thermometer is suitable for use in research facilities and general laboratories while conducting wide range of experiments. It features 14 to 38 degree C range with 0.2 degree C divisions.

For use with viscous fluids, semi-solid bitumens, emulsions, etc. For ASTM Standards D 70, D 115, D 234, and D 1963; also for AASHTO standards T-43, T-151, and M-125; and ANSI Methods A37.71 and K34.1 Standard taper 24/12 solid stopper, concave on the under side, with central opening 1.6 mm bore …

Pycnometer bottles are provided with non-mercury, red-spirit filled thermometers for facilities that are designated mercury-free. Bottles are designed with a special, medium length standard taper 10/18 joint and are retested for accuracy within ±0.2°C. Cap for side tube is medium length standard…

This borosilicate glass specific gravity bottle is used in standard test methods for specific gravity of a variety of semi solid materials and emulsions, such as asphalt cements, road tars, road oils, and soft tar pitches. The solid Standard Taper stopper has a hole approximately 1.6mm in diameter…

…recommended for male blood donors. RICCA CHEMICAL COMPANY determines the specific gravity of its Copper Sulfate Specific Gravity solutions using a pycnometer, a very accurate device for determining specific gravity, and a temperature of 25°C (77°F). The specific gravities of these solutions are…

…when overflowing in a clean special PYREX® brand glass cylinder. They check laboratory determinations made with the Boot or Reischauer pycnometer. All instruments and cylinders must be kept clean. We have found chromic-sulfuric acid (Cleaning Solution) most satisfactory for this purpose.…

Density2Go Two Choices Made for use in the lab and on-the-go, the Densito and DensitoPro are perfect for all applications: from quality control of incoming goods to at-line quality assurance of intermediate or final products. Temperature compensation factors correct the measurement…

Thermometer for use with specific gravity pycnometer 15123R-10 (8350F10 ) or 15123R-25 (8350F17 ). Medium length Standard Taper 10/18 thermometer with a range of 14 to 38 degrees C Subdivided in 0.2 degree C increments Accurate to ± 0.2 degrees C Caution: Contains…

The Omni TH is a powerful Tissue Homogenizer designed to handle a wide range of laboratory samples from 0.2 mL to 100 mL in volume. The TH tissue homogenizer can usually process a tissue sample in less than 30 seconds and is compatible with a wide variety of generator probes for flexibility in…