Laminar Hood Flow Labconco

Purair® FLOW series laminar flow hoods are designed to protect the work surface, products and materials from particulate contamination. Room air passes through a HEPA filter then uniformly by laminar flow through the cabinet interior to protect the work from unfiltered air. The airflow is…

Purair® Laminar Flow Hoods are a series of high efficiency products designed to protect equipment and other contents of the work zone from particulates, for applications sensitive to such contamination. The series includes Vertical Laminar Flow (VLF) cabinets and Horizontal Laminar Flow…

The Labconco Logic+ Class II A2 Biosafety Cabinet excels in user comfort and functionality. Decades of industry leading advances in ergonomic design have shaped the Inclination™ Technology Suite that includes the following: 10° angled sash, patented curved air grille with built in…

LED, Direct Wired T8 x 3' – newest models use on 4' & 8' Hoods – 12 watts each

Designed to vent non-toxic materials such as heat, steam and odors from large or bulky apparatus such as ovens, steam baths and autoclaves, wall-mounted or suspended from the ceiling, built-in baffle to increase air velocities and enhance its overall capture efficiency, glacier white epoxy-coated…

Protector Stainless Steel Radioisotope Laboratory Hood. Provides protection from applications requiring the use of radiochemicals. Seamless type 304 stainless steel liner with integral work surface.

Protector Stainless Steel Perchloric Acid Laboratory Hood. Designed specifically for procedures involving the use of perchloric acid. One-piece Type 316 stainless steel liner is free of joints to prevent build-up and simplify decontamination. By-pass airflow design. Built-in washdown system with…

….57" H2O at 100 fpm (1120 CFM) for hoods without blower module. Dimensions: 70" W x 25" D x 53" H. A water gauge is used for static pressure measurements. Four inches of water is approximately equal to one inch of mercury. Labconco XPress Laboratory Equipment …

For use with Labconco XPert Systems and Purifier Class I and HEPA Filtered Enclosures. Allow the enclosure to be thimble-ducted to the outside for additional protection. The canopy's air gap provides a means of balancing air by allowing room air to enter the ductwork and mix with the…

…conformity (115 volt models) ETL listing (115 volt models) CE Conformity marking (230 volt models) Features Horizontal laminar flow Supply HEPA filter, 99.99% efficient on particles 0.3 micron (2 each on 8' models) Double-gasket, negative pressure HEPA filter leak…

…may be mounted atop the enclosure in factory-prepared location. LCD displays actual face velocity within the hood. Audible and visual alarms indicate when velocity of the hood falls below set point. Includes airflow sensor, face plate with circuit board, epoxy-coated steel housing, electrical…

…XPert Bulk Powder Filtered Systems, XPert Filtered Balance Stations, XPert and RXPert Filtered Balance Systems Enclosure Nominal Width: 3', 6' Filter Application: Particulate Filter Flow Type: Supply Filter Length (Inches): 30 to 40 Rated CFM: 327 CFM

Service Fixture Kit, includes serrated hose tip valve with quarter turn control handle, hardware and instructions for plumbing to services. Up to two fixtures may be mounted on the right hand side of the Purifier Horizontal Clean Bench.

IV Bar Kit, supports intravenous solution bottles and bags. Kit includes IV Bar, mounting hardware, four hangers and instructions for installation. 3' and 4' Purifier Horizontal Clean Benches accommodate one IV Bar. 6' benches accommodate two.

Vibration Isolation Table, provides an isolated work surface for conducting procedures with vibration-sensitive equipment such as microscopes and balances. The table never makes contact with the clean bench so vibration from the motor/blower is not transmitted to the table. Epoxy-coated steel frame,…

Caster Kit for Base Stands, adds mobility to Hydraulic Lift Base Stands. Kit includes four 5" diameter, non-marking polyurethane casters with toe locks. Casters will replace fixed feet included with the stand.

For use with Purifier Logic Biosafety Cabinets & PuriCare Procedure Stations Service Fixture Kit, includes serrated hose tip valve with ball valve, quarter turn control handle, hardware and instructions for plumbing to services. Mounts on left or right side interior.

Airflow Sensor Kit displays inflow and downflow velocities on MyLogic OS of LCD screen. Includes sensor, wiring harness and hardware. Installation and certifier calibration required.

Small Tubing Pass-Throughs for passage of larger tubing through sidewall of Logic Vue for external equipment such as Aerosol Management Systems (AMS), chillers, and other supportive equipment. Inner tube and outer flange constructed of a 16 gauge 304 stainless steel. Adds 1.8" (4.6 cm) to…

Safety Interlock Cable provides interface between the Logic Vue and automation devices that employ a safety interlock. Opening the sash of the Vue triggers the interlock, immediately signaling a device to pause or stop.

Large Tubing Pass-Throughs for passage of larger tubing through sidewall of Logic Vue for external equipment such as Aerosol Management Systems (AMS), chillers, and other supportive equipment. Inner tube and outer flange constructed of a 16 gauge 304 stainless steel. Adds 1.8" (4.6 cm) to…

Securely support a laptop computer within easy view of an operator seated at the Purifier Logic Biosafety Cabinet or PuriCare Procedure Station. Mount to front of SoLo Base Stands or front leg of Telescoping Base Stands. Articulating arm raises, lowers and pivots to a steady position. Include…

“Lazy Susan” holds miscellaneous items and rotates 360° to bring items within easy reach Stainless steel surface and ball bearings 12 in. (30 cm) diameter Autoclavable Shipping weight 5 lbs. (2 kg)

Mounts in vertical duct run to prevent reverse pressurization of the exhaust system 3.0" (8 cm) high with 10" (25.4 cm) diameter OD inlet and outlet Shipping weight 5 lbs. (2 kg)

Includes four stainless steel seismic brackets and hardware for attachment to the stand Hardware to attach to the floor and installation are required Shipping weight 10 lbs. (4.5 kg)

Mounts atop the Canopy Connection to adjust exhaust airflow and closes for decontamination procedures Manually adjustable, type 304 stainless steel 10"(25.4 cm) high with 10"(25.4 cm) diameter OD inlet and outlet Shipping weight 13 lbs. (6 kg)

Includes three stainless steel mounting hooks and three carabiners Hooks mount to the rear grille Carabiners secure power cords and tubing along the rear wall to keep them contained and away from the work area Shipping weight 3 lbs. (1 kg)

Stainless steel Mounts to rear grille and provides 8.0" x 5.0" (20 x 13 cm) surface to place supplies Weight capacity: 2.2 lbs. (1 kg), shipping weight 3 lbs. (1 kg)

PVC Blower, made specifically to handle extremely corrosive atmospheres produced by high order oxidizers such as perchloric acid. Features: Vacuum formed housing of unplasticized Type I polyvinyl chloride for complete corrosion protection; inlet and discharge diameters are sized to receive rigid PVC…