Hplc Ferrules

Compare Tool

Select up to 3 products

Hplc Ferrules
1 - 32 of 39
Sort
View
Show
  • Upchurch PEEK Fingertight Fitting nut and ferrule 10-32

    MilliporeSigma

    …and ferrule 10-32 General description The one-piece fitting, 55067-U, is convenient to use because the ferrule will not stick in a receiving port and can be easliy found if dropped onto the floor. The two-piece fitting features a separate ferrule so you can replace just the ferrule instead…

  • Fittings and Ferrules for 1/8" Tubing

    Restek

  • FERRULE .27 ID PEEK HPLC

    Thermo Scientific

  • EXP Hex-Head Fittings

    Restek

    Hand-tight fitting style achieves effortless HPLC seals—no tools needed for a 8,700+ psi seal Both hand-tight and hex-head styles wrench-tighten for reliable UHPLC use up to 20,000+ psi! Patented ferrule can be installed repeatedly without compromising high-pressure seal Hybrid design…

  • Replacement Trident PEEK Ferrules

    Restek

  • Rigid Capillary Tubing

    Agilent Technologies

    Squarely cut, pre-cleaned and ready to use Use with stainless steel fittings and ferrules or PEEK fittings

  • EasyLOK Fittings

    SGE

    …Unlike stainless steel, the PEEK™ ferrule will not crush the tubing and can be easily readjusted for quick column changes. The unique double ended ferrule design seals at two points to prevent leaks. The fittings are compatible with any standard female HPLC fitting, including Swagelok®,…

  • EZwaste® Replacement Fittings

    Foxx Life Sciences

    …OD Tube Fittings Pack is the replacement fittings for EZwaste® Solvent Waste System's fittings. It includes 30 Male-nut fittings and 30 Ferrule fittings for 1/16" OD Tubing. These tube fittings secure waste tubes to carboy providing the closed system necessary to prevent spills. …

  • 1/16" Stainless Steel Ferrule

    Restek

  • HPLC Mobile Phase Cap And Reservoir Systems

    DWK Life Sciences (Kimble)

    …Systems include the following: economy three hole cap; flat bottom reservoir; All PEEK Inlet/Sparge Filter (2 µm); two flangeless nuts, ETFE, 1/4-28, 1/8”; flangeless ferrules, ETFE, 1/8”; nut plug, ETFE, 1/4-28; FEP tubing, 1/8” o.d. x 1/16” i.d. x 10’ length; and an Instruction Manual.

  • HPLC Poly Manifold for Quick-Disconnect Safety Disposal Cans

    Justrite

    The HPLC Poly Manifold enables up to six waste lines (per manifold) from HPLC processes to be fed into a single intake fitting. Manifolds have six 1/4-28 ports and one 3/8" NPT port (all come with caps for unused ports) and either one quick disconnect in No. 316 stainless steel or…

  • 1/16" Ferrules for Secure-Fit Fittings

    Restek

  • Column Blank Kit for HPLC

    MilliporeSigma

    Each column blank kit includes a precision-bore polished 316 stainless steel column blank, two zero dead volume external reducing unions (internal unions with 10 mm I.D. blanks) with nuts and ferrules for 1/16 in. O.D. tubing, and two 2 μm frits.

  • Upchurch PEEK Fingertight Fitting, fitting 10-32 (one-piece)

    MilliporeSigma

    …one-piece fitting, 55067-U, is convenient to use because the ferrule will not stick in a receiving port and can be easliy found if dropped onto the floor. The two-piece fitting features a separate ferrule so you can replace just the ferrule instead of the entire unit. The Upchurch PEEK Fingertight…

  • Ferrule for Waters HPLC Systems

    Restek

  • Rheodyne Style Nut and Ferrule

    Restek

    Replacement long nut for connecting stainless steel tubing to a Rheodyne 6-port valve or other Rheodyne part.

  • Survival Kit for HPLC, Stainless Steel

    Restek

    …x 10 cm, 3-pk. HPLC Capillary Tubing, SS, 1/16" x 0.020" x 20 cm, 3-pk. HPLC Capillary Tubing, SS, 1/16" x 0.020" x 30 cm, 3-pk. 1/16" Rheodyne Style Nut, 10-pk. 1/16" Rheodyne Style Ferrule, 10-pk. ValvTool Wrench, ea. Ferrules, 1/16" Stainless…

  • EXP Hand-Tight Coupler

    Restek

    Hand-tight fitting style achieves effortless HPLC seals—no tools needed for a 8,700+ psi seal Both hand-tight and hex-head styles wrench-tighten for reliable UHPLC use up to 20,000+ psi! Patented ferrule can be installed repeatedly without compromising high-pressure seal Hybrid design…

  • Stainless Steel Tubing

    SGE

    Smooth and clean bore. Supplied in coils and enclosed in a stainless steel spiral mount. Where tubing OD is smaller than 1/16", ends are bushed to 1/16" and GC ferrules are supplied.

  • PEEKsil™ Injection Loop

    SGE

    …loss due to shear or adsorption Maximum operating pressures are 3000psi for 10µL, and 20µL loops Supplied with PEEKsil™ tubing and two sets of Stainless Steel Hexnuts™ with PEEK ferrule fittings Compatible with most valves including Rheodyne® and Valco®

  • SUPELCOSIL™ LC-NH2 Supelguard™ Cartridge

    MilliporeSigma

    eCl@ss 32110501 Footnote Kit includes one cartridge, a stand-alone holder, a piece of tubing, and 2 nuts and ferrules. Legal Information SUPELCOSIL is a trademark of Sigma-Aldrich Co. LLC Supelguard is a trademark of Sigma-Aldrich Co. LLC

  • Trident LC Column Protection System

    Restek

    …LC column protection system is a reusable direct connect holder that easily attaches to any HPLC column with standard 10-32 thread ports.* The holder’s durable metal tip and replaceable PEEK ferrule allow a leak-tight seal onto the column to be made quickly and easily without tools. Guard…

  • Slipfeee Ferrules

    Thermo Scientific

    For use with SLIPFREE connectors for HPLC columns Vespel ferrules replace the standard Vespel ferrules supplied with SLIPFREE column connectors Kel-F and PEEK are offered for applications in which Vespel is not suitable

  • EXP Hand-Tight Fittings

    Restek

    Hand-tight fitting style achieves effortless HPLC seals—no tools needed for a 8,700+ psi seal Both hand-tight and hex-head styles wrench-tighten for reliable UHPLC use up to 20,000+ psi! Patented ferrule can be installed repeatedly without compromising high-pressure seal Hybrid design…

  • EXP Direct Connect Holder

    Restek

    …architecture lets you change cartridges by hand without breaking inlet/outlet fluid connections—no tools needed Patented titanium hybrid ferrules can be installed repeatedly without compromising high-pressure seal Auto-adjusting design provides ZDV (zero dead volume) connection to any…

  • Trident HPLC In-Line Guard Cartridge Holders

    Restek

    A Trident in-line guard cartridge holder can be used with almost any HPLC column by connecting it with a short piece of 1/16" tubing, appropriate nuts and ferrules, or finger-tight fittings. The system can be used with Restek columns, or with columns from other manufacturers. Holders are…

  • PEEKsil Tubing

    SGE

    …polymer is polyether ether ketone (PEEK) that is mechanically strong and has ideal characteristics for sealing with conventional metal or polymer ferrule systems. PEEKsil may be used as a direct replacement for conventional stainless steel as well as a replacement for PEEK tubing used in liquid…

  • EXP Titanium Hybrid Replacement Ferrules

    Restek

    Hand-tight fitting style achieves effortless HPLC seals—no tools needed for a 8,700+ psi seal Both hand-tight and hex-head styles wrench-tighten for reliable UHPLC use up to 20,000+ psi! Patented ferrule can be installed repeatedly without compromising high-pressure seal Hybrid design…

  • High Pressure Stainless Steel Nuts and Ferrules

    Thermo Scientific

    Accommodate a wide range of configurations Designed for 10-32 port configurations Burr and contaminant free

  • Supeltex® M-2A Capillary Ferrule, General Purpose

    MilliporeSigma

    I.D. 0.4 mm, 0.10-0.25 mm Column I.D. Characteristics: Seals at 1/4 turn past fingertight. High reusability. Won't stick to metal or glass. Material Composition: DuPont VESPEL SP-21 (85% polyimide, 15% graphite) Maximum Temperature: 400 °C Legal Information Supeltex is a registered…

  • Supeltex® M-2A Packed Column Ferrule, 1/4 in. Column O.D.

    MilliporeSigma

    I.D. 1/4 in., 1/4 in. O.D. Column Characteristics: Seals at 1/4 turn past fingertight. High reusability. Won't stick to metal or glass. Material Composition: DuPont VESPEL SP-21 (85% polyimide, 15% graphite) Maximum Temperature: 400 °C Legal Information Supeltex is a registered…

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.