Glass Vacuum Chamber

Twin chamber vacuum trap for double protection against undesired vapors in a vacuum system. Trap can be used in a two liter Dewar flask such as 12540-07. Distance from outside of one body to outside of other is approximately 97mm; height is 250mm. Inlet and outlet have serrated fittings; O.D. of…

SPE Vacuum Manifolds accommodate either 12 or 24 cartridges; 1, 3, 6, 15 and 25 mL columns can be used. Manifolds are equipped with a vacuum port to connect a standard laboratory vacuum pump. Vacuum pulls the sample through the stationary phase, metered by the stopcocks, to control the speed of the…

SPE Vacuum Manifolds accommodate either 12 or 24 cartridges; 1, 3, 6, 15 and 25 mL columns can be used.  Manifolds are equipped with a vacuum port to connect a standard laboratory vacuum pump.  Vacuum pulls the sample through the stationary phase, metered by the stopcocks, to control the speed of…

…and vacuum sources. Double vacuum gas manifold with vacuum chambers. Fabricated from 1/2" medium wall tubing Stopcocks are 4 mm bore glass with lower vacuum chamber and are spaced 85 mm apart Top right connection is for inert gas and lower left connection is for vacuum …

…components of this chamber are rated at higher temperatures however as a vacuum vessel we limit maximum operational temperature to 160f. Every chamber is tested prior to shipping to lose no more than 2.5Hg/24hrs. This Kit Includes: (1) Soda lime triple tempered glass bowl (1)…

…with floating tempered glass, assure an excellent seal at all vacuum levels Clear polycarbonate safety shield protects door glass from damage Front-mounted vacuum line fittings accept 1/4 i.d. vacuum tubing Side-mounted control panel, with all controls and vacuum line connections in a single,…

Drying samples for elemental analysis. Sample is placed in a vial which is placed into drying chamber. Under vacuum and gentle heat created by refluxing in outer jacket of low boiling point solvents.

…microprocessor-controlled motor; phenol-free gasket; audible alarm. In addition, the system has automatic vacuum release, Teflon-coated aluminum chamber and sample blocks, glass lid with Lexan shield; dual lid clamps, and an easy-to-read LCD display. The cabinet base is epoxy-coated cast…

Precision grade, with 3-way oblique stopcock. Available with oblique bore hollow or solid plug. Plug has hole to permit evacuation of the lower chamber and prevents leakage through the bottom.

… Outer case constructed of a tough steel construction Vacuum chamber is a robust, light alloy casting Spacious rectangular chamber with toughened glass viewing window and polycarbonate shatter-resistant safety screen Glass fiber insulation increases energy efficiency Supplied with 2…

…diameter hard tubing for pump and air connections Vacuum and air lines of corrosion-resistant stainless-steel tubing optimize chamber cleanliness and long-term performance Durable exterior is powder-coated heavy-gauge steel Glass window in the door allows for sample viewing Two…

…LAB vacuum ovens are built with a stainless steel chamber for exceptional durability. Our double plenum design meets UL, CSA and EU safety requirements resulting in a cool outer surface. Our unique cross-flow ventilation forces inert gas to fill the entire chamber. To achieve required vacuum…

…and lid are ground glass and require greasing before use to create an air-tight seal. Also includes a perforated porcelain desiccator plate that fits onto a ridge above the lower chamber. A standard drying agent such as silica or anhydrous calcium chloride can be positioned in the lower chamber.

…for items up to 18” (45 cm) tall or wide including racks, trays and instruments, this Vacuum Desiccator provides for much more storage in a single chamber than traditional plastic or glass vacuum desiccator units. All contents can be easily viewed through the desiccator's clear…

…LAB vacuum ovens are built with stainless steel chambers that are easy to clean and have exceptional durability. The doors on these units have positive latch handles with spring-loaded glass to facilitate a good vacuum seal without hinge binds that shorten the gasket life. The tempered glass…

…atmosphere; vacuum valves provide means of vacuum atmosphere removal; vent port releases atmosphere from chamber. Built-in electrical outlet is included on all models for a vacuum pump. One inch manifold allows for easy connection to house vacuum. Atmosphere inlets are located in rear of chamber for…

…to 1725 RPM; Quick-Stop System to stop vacuum pump, open valve and stop rotor; automatic vacuum release valve; lid latch with safety sensor; epoxy-coated, 12" diameter chamber to accommodate a variety of rotors; large, phenol-free lid seal; built-in vacuum delay; easy-to-read LCD display; separate…

…bench space or storage space. - Built-in Teflon-coated diaphragm pump with ultimate vacuum of 160 mBar and displacement capacity of 5.5 liters/minute IR-emitting transparent glass lid Teflon-coated aluminum chamber Teflon-coated aluminum rotor included for 24 each, 1.5 ml microcentrifuge tubes …

…conserves chamber space for drying, curing, vacuum embedding and plating applications. 3 in.(7.6cm) glass wool insulation prevents heat loss Silicone door gasket and positive latch door maintain seal at all vacuum levels Polycarbonate safety shield protects door glass Vacuum level…

A BINDER vacuum drying oven VD series gently dries materials with homogeneous temperature distribution. The patented expansion shelf technology from BINDER ensures optimal heat transfer. The shelves are easy to position where required and the inner chamber of the vacuum drying oven is easy to clean.…

…ATEX-compliant safety concept ·         Also option of modular complete system with vacuum pump and pump chamber   Important characteristics ·         Temperature range: +9…

…to 1725 RPM; Quick-Stop System to stop vacuum pump, open valve and stop rotor; automatic vacuum release valve; lid latch with safety sensor; epoxy-coated, 12" diameter chamber to accommodate a variety of rotors; large, phenol-free lid seal; built-in vacuum delay; easy-to-read LCD display; separate…

With 4mm double oblique, high vacuum hollow glass stopcocks precision ground with corresponding numbers on barrel and plug. Lower vacuum chambers on stopcock are evacuated with a separate hole in the plug in order to hold the plug in the stopcock barrels. Distance between stopcocks is 75mm center to…

…dry system while providing visibility into the chamber during bulk drying. Chambers are available in small and large sizes, with or without valves. Chambers include clear acrylic cylinder, 1/2” thick clear acrylic top and bottom lids, vacuum break valve, gaskets and electrical pass through…

Chamber for use in drying small quantities of material in dram vials. Can also be used in the transfer of materials from glovebox to glovebox or to the vacuum line. Lower vessel has a flat bottom permitting it to be stood upright on the bench or in a glovebox. Top adapter has a 0-4mm Chem-Vac™…

Three-way high vacuum oblique bore stopcock with liquid seal. The solid plug is bored to permit evacuation of the lower chamber and prevents leakage through the bottom.

… Polycarbonate safety shield protects door glass Vacuum level is displayed on gauges from 0 to 30in Hg Vacuum and air lines are corrosion-resistant stainless-steel tubing for optimum chamber cleanliness and long-term performance Vacuum fittings require 0.25in. (0.6cm) I.D. tubing …

…flange Corning 6885 Made from specially selected mold-blown blanks Bottom flange has a finely ground finish to assure tight sealing with ground glass plates Dimensions (ID x OD): 1577J18 Jar: 5 1/8” x 5 1/2”; 1577J33 Jar: 6 1/8” x 6 1/2”; 1577J48 Jar: 8 3/8” x 8…

…rotor, diaphragm, vacuum pump, two glass traps and all connecting tubing. Large chamber and rotors hold more samples. Integrated diaphragm pump is corrosion-resistant. DNA rotor holds up to 60 x1.5 mL tubes and 72 x 0.5 mL tubes. Two 177 mL glass traps protect the vacuum pump and the environment.…

Twin chambered dry ice condenser-trap similar to 8748 except dry ice finger condensers in this unit are NOT removable. Ports at top for connecting to Rotary Evaporator and to vacuum source are 3/8" O.D. Condensate stopcock at bottom is 4mm PTFE, 90 degree bore, that allows draining each chamber…

Twin chambered dry ice condenser-trap,for Rotary Evaporator use. Squatty design 18"high, two chambers. Dry ice fingers secured in main body via #50 Ace-Thred, bushings, and O-Rings allowing for easy cleaning. Two ports at top of chamber are 3/8" O.D. (for connecting to evaporator & vacuum source).…