Glass Inlet Adapter

Synthware inlet adapter with extended length lower tube. Allows for the introduction of reactants below the interior surface. Tube extends 153mm (6 inches) below the joint. Tubing has the same O.D. on both ends of the joint.

Side tube with hose connection. Stem below joint is 175mm. Hose Conn. size D. Available in 24/40 and 29/42 standard joints or 35/25 spherical joints.

Inlet Connecting Adapter, High Vacuum Valve Joint: #15 O-ring Valve Size: 0-4mm Side Port: 10mm OD.

Ideal for use as a vent or for the introduction of pressure/vacuum Glass male Standard Taper joint with hose barb for tubing at 90° angle Thomas numbers 5737A01 and A03 take 1/4” tube fitting; others are 3/8”.

Gas Inlet/Outlet Adapter, Microscale, Synthware, Joint: 14/10, Hose Connection OD: 8mm.

Thermometer Adapter, Microscale, Synthware, Joints: 14/10, Thermometer OD: 5.0-7.5mm, supplied with one compression cap and one Viton O-ring.

Ai Thermometer Inlet Adapter with Sealing Gasket.

Synthware inlet adapter with a standard taper inner joint. Design allows introduction of reactants below the surface. The serrated hose connections have an O.D. of 10 mm.

This gas balloon type adapter is used for protective storage in jointed vessels. The inert gas tubing may be disconnected, giving the vessel its own portable inert gas source to balance volume changes caused by sample removal Supplied without the balloon Replacement retainer is…

For use with gas inlet tubes or plain stem thermometers. Supplied with one holed rubber adapter.

…suitable for use to 150 °C To use it as a septum port, just replace the o-ring with a PTFE-lined septum Supplied with one FKM o-ring and one 410119 cap Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. 

This precision-engineered adapter may be cut with a fine-tooth saw or sharp knife into various adapters, such as individual bushings, stirrer bearings, thermometer and gas inlet tube supports, drip-tips, funnels, trap connectors for tubing, etc. Forms a continuous standard taper inside and…

Borosilicate glass universal inlet adapters are capable of sealing thermometers, syringes, pipets, etc. Insert probes can be positioned within the apparatus by loosening the screw cap on top of adapter and tightening to create a seal. Bottom of adapter features a Standard Taper joint. Supplied as a…

Synthware long stem inlet adapter. With standard taper top outer joint and lower inner joint with sealed in lower tube extending below the inner joint.

Ideal for use as a vent or for the introduction of pressure/vacuum. Inner Standard Taper joint at one end and vertical hose connection at the other Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

Used for converting a single neck round bottom flask to air-free or vacuum applications. Outlet can be either 2mm glass stopcock or a 0-3 inlet valve. Upper and lower joint sizes are the same size. Great for adapting flasks and other components for Schlenk lines.

With 24/40 standard taper inner joint and vacuum take-off. Hose connection is size D.

With 24/40 standard taper inner and outer joints and side hose connection size D.

Adapter with side hose connection. Use as gas inlet or vacuum adapter. With 14/10 or 14/20 externally threaded top outer joints and 14/10 or 19/38 inner joints and size A or B serrated hose connection off side. Supplied with holed cap and FETFE O-Ring.

Stopcock available with glass or PTFE plug For regulating the flow of gases or liquids into reaction systems. Adapter consists of male standard taper joint fittng with stopcock and a 90° angle male hose barb. Thomas numbers 5738D01, D03, D15, and D17 take 1/4" i.d. flex tubing; Thomas…

Adapter has a tubulation at the top for use with a CG-1040 rubber fitting. Fitting permits insertion of plain stem thermometers or bleed tubes. Supplied complete with one CG-1040 rubber fitting.

Adapter has a #7 or #15 Chem-Thread at the top for vacuum tight seal of plain stem thermo-meters or any other tube having an O.D. between 4 and 7mm. Supplied complete with a Celcon® compression cap and Viton o-ring.

Made entirely of PTFE, adapter has an inner joint of the listed size. The compression nut allows for vertical adjustment of thermometers or bleed tubes having an O.D. between 6 and 7mm. Supplied complete with one #108 Viton o-ring.

Adapter has the listed size of Chem-Thread at the top for a vacuum tight seal of a variety of tubing diameters. Will accept glass, metal or heavy wall plastic tubes having diameters between 7 to 18mm O.D. such as thermometer wells, gas dispersion tubes, plain stem funnels, etc. Adapters are supplied…

Unique adapter is made entirely of PTFE and is supplied complete with a series of 5 all PTFE ferrule style cones. These cones have inside diameters that run from 3.5 to 6.5mm and seal against the inserted tube by means of a threaded compression screw. Cones are color coded for easy identification.…

Adapter has a Nylon compression cap and a Viton o-ring to form a vacuum tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. The 8mm hose connection can be used for N2/Ar introduction or vacuum. Supplied with one Nylon cap and one Viton o-ring.

Synthware inlet adapter with an extra coarse porosity fritted disc between the serrated hose connection and the standard taper inner joint. The disc prevents solids from being introduced into the reaction system during liquid transfer.

…bottom and a tubulature at the top Includes a rubber adapter with a ¼" hole in the top for use with plain stem thermometers, gas inlet tubes, etc. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

…0-60psi and up to 0-400psi. Gauges have different NPT end fittings and internal materials, as well as various dial ranges. Some come with nylon adapters to match to Ace-Threads, NPT threads and 1/4-UNF threads. One style comes complete with a 3-way tubing connector for in-line connection. Code -52…

Adapter has a Nylon compression cap and a Viton o-ring to form a vacumm tight seal. Cap accommodates 5.0 - 7.5mm O.D. thermometer or gas inlet tube. To use it as a syringe port, simply replace the o-ring with a PTFE-lined septum. Supplied with one Nylon cap and one Viton o-ring.

Gas inlet adapter with a 2mm glass stopcock having a constant pressure retention device. Available with a choice of inner or outer standard taper joint. Top arm is 9mm O.D. medium wall tubing for use with CG-3022 septum. Overall height of the 14/20 size is approx. 95mm while the 24/40 is approx.…