Filter Paper Glass Fiber

…temperatures. As specified for the analysis of water and waste samples in the Standard Methods for the Examination of Water and Wastewater (1992) Retains precipitates such as silver chloride Compares favorably with fritted glass filter crucibles Maximum usable temperature 500°C

TSS Filters are recommended for use in Standard Methods 2540 C and 2540 D. Optimized surface characteristics of this binderless borosilicate glass microfiber filter eliminates pin-holing and fiber-shedding to ensure consistent, accurate results comparable to 934-AH® brand filters. Fast flow…

…borosilicate glass, binder-freeExtends life of final filter membraneGE’s Whatman GMF 150 prefilters are multilayer graded density filters for rapid and efficient filtration of samples with high solids content. Multilayer filter design When a sample is applied, the multigrade glass filter traps…

Depth filters with high particle loading capacity. Made of 100% borosilicate. Temperature resistant up to 500 °C. Typically placed directly on top of other membrane filters to act as a prefilter; or may be used to filter solutions directly.

… Most widely used in biochemistry for filtration of precipitated proteins Withstands temperatures to 500°C Attains much higher counting efficiencies compared with cellulose papers; borosilicate glass without binders Widely used for reliable results in air pollution analysis

Grade GF/C is the standard filter in many parts of the world for the collection of suspended solids in potable water and natural and industrial wastes. Grade GF/C: 1.2 µm Combines fine particle retention with good flow rate. Fast and efficient clarification of aqueous liquids…

…and are easily sterilized. Wide, useful temperature range which can be used at 500°C and at low temperatures. Three times thicker than GF/A and with greater wet strength Borosilicate glass fibers 1.0 µm particle retention 0.7 mm thick; filtration speed 5.5 mL/second

Acrylic binder High dirt holding capacity Biologically inert Bonding reduces media migration

…and at low temperatures. Made from less fine fibers, thick with a very high-loading capacity Particle retention 2.7 µm Extremely high speed; ten times more rapid than the fastest comparable retention cellulose filter paper Withstands temperature to 500°C Designed as…

Advantec Glass Fiber Filters are depth filters made of pure borosilicate glass microfibers. Highly resistant to chemical attack and biologically inert. Binder-free and thermostable to 500°C. These grades are recommended primarily used in environmental air monitoring applications. Grade…

…glass. GF/F offers very fine particle retention and good loading capacity and flow rate. 0.7 µm nominal particle retention Served as the basis filter for EPA standard for the toxicity characteristic leaching procedure GE’s Whatman brand glass microfiber filters provide…

ValuSep® 5um Glass Micro Fiber (GMF) prefilters are made of two separate layers of glass fiber in a very thin format for highly efficient capture and retention of particles that could prematurely clog an SPE filter.

Binder-free, borosilicate glass microfiber Filters are designed to determine the leaching potential in a landfill for hazardous organic and inorganic contaminants that could potentially migrate into groundwater and drinking water sources. Particle retention rating of 0.6 to 0.8…

…filtration of media that are difficult to filter, especially those that are highly viscous. Membranes, paper or glass fiber filter discs can be used. Cleaning and changing of filters is completed in a few steps. All units are equipped with pressure-resistant filter supports. High-quality silicone…

Advantec Glass Fiber Filters are depth filters made of pure borosilicate glass microfibers. These grades are thicker and have a high loading capacity and typically faster flow times. Recommended for filtering viscous fluids such as proteinaceous solutions and gels and as prefilter to extend membrane…

Advantec Glass Fiber Filters are depth filters made of pure borosilicate glass microfibers. Organic binder gives these filters higher wet strength and lower fiber release compared to binder-free grades. Thermostable to 120°C. Recommended for high pressure filtration, applications requiring wet…

Advantec Glass Fiber Depth Filters feature high-loading capacity, fast flow rates, are highly resistant to chemical attack, and biologically inert. General purpose and clarifying filtration grades. Binder-free and thermostable to 500°C. Grade GA55 is a thin filter recommended for…

Highly absorbent white fiber paper Lint and dust free Recommended for drying microscope slides and other small lab glass items

…premature clogging when filtering difficult-to-filter or highly contaminated solutions Extends filter life and reduces final filter changes with high capacity prefilters Eliminates sample contamination. Binder-free borosilicate glass fiber has no added extractables Filters a wide range of…

…analytical papers with similar particle retention. Widely used as a depth type pre-filter ahead of final membrane filters. Sometimes used in combination with grade 121 as a graded porosity protective and retentive pre-filter for highly-efficient protection of membrane filters. GRADE 131…

…precipitate is collected on a glass fiber filter, such as Grade 169, to measure its weight and radioactivity. STM 7500-Sr Strontium Detection: Precipitation Method The precipitate is collected on a paper filter, such as Grade 94, or a glass fiber filter, such as Grade 169, to measure its…

…efficiency rating of the filter is characteristic of the complex pore structure that develops as the fibers overlap. The fibrous material within the filter is commonly glass micro fiber or polypropylene. In depth filters such as glass micro fiber, the purity of the filter is dictated by the presence…

…Polystyrene (PS) Fiber filter plug Reverse graduations Negative graduations Sterilized by gamma irradiation Sterility assurance level (SAL): 10 -6 Non-pyrogenic Individually wrapped styles are in thermoformed paper/plastic peel packaging Safe alternative to glass pipettes …

…applications. Material: Polystyrene (PS) Fiber filter plug Sterilized by gamma irradiation Sterility assurance level (SAL): 10 -6 Non-pyrogenic Individually wrapped in thermoformed paper/plastic peel packaging Safe alternative to glass pipettes Calibrated to deliver (TD)…

…efficiency rating of the filter is characteristic of the complex pore structure that develops as the fibers overlap. The fibrous material within the filter is commonly glass micro fiber or polypropylene. In depth filters such as glass micro fiber, the purity of the filter is dictated by the presence…

…efficiency rating of the filter is characteristic of the complex pore structure that develops as the fibers overlap. The fibrous material within the filter is commonly glass micro fiber or polypropylene. In depth filters such as glass micro fiber, the purity of the filter is dictated by the presence…

…efficiency rating of the filter is characteristic of the complex pore structure that develops as the fibers overlap. The fibrous material within the filter is commonly glass micro fiber or polypropylene. In depth filters such as glass micro fiber, the purity of the filter is dictated by the presence…

…efficiency rating of the filter is characteristic of the complex pore structure that develops as the fibers overlap. The fibrous material within the filter is commonly glass micro fiber or polypropylene. In depth filters such as glass micro fiber, the purity of the filter is dictated by the presence…

…efficiency rating of the filter is characteristic of the complex pore structure that develops as the fibers overlap. The fibrous material within the filter is commonly glass micro fiber or polypropylene. In depth filters such as glass micro fiber, the purity of the filter is dictated by the presence…

…efficiency rating of the filter is characteristic of the complex pore structure that develops as the fibers overlap. The fibrous material within the filter is commonly glass micro fiber or polypropylene. In depth filters such as glass micro fiber, the purity of the filter is dictated by the presence…

…efficiency rating of the filter is characteristic of the complex pore structure that develops as the fibers overlap. The fibrous material within the filter is commonly glass micro fiber or polypropylene. In depth filters such as glass micro fiber, the purity of the filter is dictated by the presence…

…Glass Fiber Filters WITHOUT Binders, 0.7 µm Pore Size (4749A72) Borosilicate glass fiber filters designed for use in U.S. EPA Method 1311 Toxicity Characteristic Leaching Procedure (TCLP). Federal regulations require the filters for this application be made of borosilicate glass fiber,…