Distillation Receivers

Compare Tool

Select up to 3 products

Distillation Receivers
1 - 32 of 117
Sort
View
Show
  • Radial style distillation receiver allows four flasks to be progressively filled. Upper vacuum adapter is bent at a 105º angle. Complete item consists of a vacuum adapter, distribution adapter, four of the listed size flasks with hooks and ten CG-110 stainless steel springs.

  • Graduated distilling receiver with a standard taper outer joint on top and a standard taper lower drip joint. Stopcocks are either a 2mm or 4mm PTFE. Distance between the receiver and the uptake arm: 10 and 20mL are 100mm center to center; the 50, 100 and 250mL are 150mm center to center.

  • Distilling receiver for use where separate fractions are desired without disturbing distillation pressure. Joints are 24/40. Receiver is 5 mL. Hose connection is size B, for use with 5/16in (7.9mm) or 3/8in (9.5mm) ID tubing. For version with 14/20 joints, or PTFE- clad version with 14/20 joints,…

  • ,p>Especially designed receiver to draw samples during distillation or to return the condensed vapor to the flask. Capacity 125ml, available with or without 1:5 PTFE plug.

  • An excellent all-purpose receiver for general distillation work. Equipped with a complete stopcock manifold to allow contents of the receiver to be removed to a single receiving flask without disturbing the vacuum of the system. Stopcocks are 4 mm bore.Tubing connections are 10mm O.D. olive type.

  • Distillation apparatus for obtaining separate fractions while maintaining constant pressure. Code -10 complete unit features ground joints and four 9458-02 5ml flasks. Code -25 complete unit features PTFE clad joints and four 9458-02 5ml flasks.

  • Similar to CG-1279 but with the top outer joint vertical instead of a 105° angle. Complete item consists of a vacuum adapter, distribution adapter, four of the listed size flasks with hooks and ten CG-110 stainless steel springs.

  • …at 105 degree angle. For operation other than at atmospheric pressure. Vacuum is applied to the side arm with the T-bore stopcock. The secondary receiver is vented by means of the lower stopcock. The capacity from the bottom of the drip to the stopcock is 2.5mL.Tubing connections are 8mm O.D. olive…

  • For operation other than at atmospheric pressure. Vacuum is applied to the side arm with the T-bore stopcock. The secondary receiver is vented by means of the lower stopcock. The capacity from the bottom of the drip to the stopcock is 2.5mL.

  • Calibrated to contain. Supplied in 10mL capacity with 0.2mL subdivisions.

  • Centrifugal type, calibrated to contain. Graduated in 0.1mL subdivisions. Total capacity 15mL.

  • The three 25mL flasks are in the same plane, rotated about the condenser axis. Hose connection is parallel to and above condenser axis. Three clips are supplied for holding flasks to condenser. All joints are 14/20. Hose connection is size A.

  • With the outer and inner joint at 135° angle, used with short-path.

  • Comes with Synthware Distilling Adapter (Joints: 14/20 or 19/22) and Cow Receivers (Joints: 14/20 or 19/22). Designed without hose connection to be used with D10 distillation apparatus. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

  • Comes with Synthware Distilling Adapter (Joints: 14/20, 19/22 AND 24/40) and Cow Receivers (Joints: 14/20, 19/22, AND 24/40). Rotating cow receiver allows four flasks to be progressively filled. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

  • Centrifuge tube shaped receiver with an upper standard taper joint has two glass hooks 180º apart. Graduated from 0 to 2mL in 0.1mL subdivisions and from 2 to 12 or 15mL in 0.2mL.

  • Graduated distillation receiver with a 4mm three way stopcock to permit solvent removal through the 10mm O.D. tube or return to distillation flask. Upper sampling port has a 2mm PTFE stopcock. The top outer and lower inner joints are the same size.

  • …the center line of the condenser and the receiver tubes allows the distillate to fall directly into the receiver tubes. This receiver can be used with short path style distilling heads. Complete receiver is supplied with distribution adapter, three 12mL receiver tubes, and six CG-110 stainless steel…

  • All-purpose receiver for general distillation work. With graduated body. Stopcocks are 4mm bore. Tubing connections are 10mm O.D. olive type.

  • Cow type design has three receivers 45° apart. Condensers with lower drip tip inner joints will protrude into the spherical section, permitting the distillate to fall directly into the receiving flasks. Distribution adapter has a serrated connection for attachment to vacuum source. Complete item…

  • This innovative and compact Dean-Stark receiver is designed for azeotropic distillations using solvents that are heavier than water. The solvent vapor travels through tube “A” to a condenser inserted in the top standard taper outer joint. Vapors are condensed and collected in the…

  • Jacketed receiver with vacuum manifold for removal of sample during operation without disturbing the system. Stopcocks on manifold are 4mm bore, receiver stopcock is 3mm. Hose connections are size E on condenser; 10mm O.D. olive on manifold.

  • Cow type reciever has a single standard taper outer joint at the top. The four lower graduated receiver tubes can be accessed via a syringe for product recovery. Tubes are graduated from 0 to 3mL in 0.2mL subdivisions.

  • Distillation apparatus for obtaining separate fractions while maintaining constant pressure. Code -30 complete unit features ground joints and (4) 9458-02 5ml flasks. Similar to our 9400 product family, however the top adapter is straight rather than b

  • With standard taper inner joint at bottom and outer joint at top. Graduated to 125mL in 1mL subdivisions.

  • With standard taper joint at top. Capacity 100mL, in 1mL subdivisions.

  • For easy separation of water from reaction or distillation system.

  • Bidwell-Sterling designed for the determination of moisture in foods and organics. 1178W31 has a drip tip Made to ASTM specifications E123 Also conforms to many methods of the American Oil Chemists Society Manufactured from 33 expansion, low extractable borosilicate glass conforming…

  • Supplied with distribution adapter, three 12mL receiver tubes and three plastic joint clip. With 135° angle between top outer joint and lower inner joint.

  • Dean-Stark receiver used for determining the water content of various materials. Can be used with ASTM Method D-95 along with similar ASTM methods. The 10mL size has subdivisions of 0.1 from 0 to 2mL, and 0.2 from 2 to 10mL. The 25mL size has subdivisions of 0.1 from 0 to 2mL and 0.2 from 2 to 25mL.

  • Similar to CG-1261 but with the addition of an overflow tube between the uptake tube and the graduated receiver.

  • Similar to CG-1258 but with the addition of an overflow tube between the uptake tube and the graduated receiver.

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.