Addition Funnel

Cylindrical funnels have a pressure equalizing line, a PTFE stopcock, and a lower drip tip Graduations to the stopcock are numbered both up and down Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements

Addition Funnel, Pressure Equalizing, PTFE Stopcock, Synthware, Capacity: 25-1000mL available, Joints: 14/20 or 24/40 available, Stopcock Bore: 2 and 4mm available. Funnels come with PTFE stopcock in pressure equalizing line.

Solvent Addition Funnel Top Diameter: 90mm Stem OD: 12, 19 or 28mm available Stem Length: 75,100, or 125mm available Design permits the addition of solvents to flash chromatography columns without disturbing the silica gel/packing layer.

ValueWare® borosilicate glass 58° long stem addition funnel with heavy uniform walls and strong, molded rims Long stems are fire polished for long service life High resistance to chemical attack, mechanical, and thermal shock Designed from ASTM specification E1095, Type I, Class B…

Cylindrical funnel has a PTFE stopcock and a glass hex head stopper 633031 is supplied without a stopper Standard Taper bottom joint is 24/40 with a drip tip Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A…

KIMAX® funnel with a short, wide stem Constructed with a heavy uniform wall and a strong, fire-polished rim and stem to provide a long service life Funnel has a high resistance to chemical attack and mechanical and thermal shock Designed from ASTM Specification E1095, Type IV…

With an equalizing arm and a special stopper so that material may be isolated from the atmosphere. Turning the stopper completely closes the vessel to the equalizing arm so that the funnel may be disconnected without exposing contents to moist air, etc

For charging columns. The capacity is approximately 5 times the largest column volume. Size listed is Ace-thred designation which refers to I.D. of tubing above thread and corresponds to 5820 column dia- meter. Available in cylindrical or conical shapes.

Addition Funnel, Pressure Equalizing, PTFE Stopcock, Synthware, Capacity: 10-1000mL available, Top Joint (Outer): 14/20, 24/40, and 19/22 available, Bottom Joint (Inner): 14/20, 24/40, and 19/22 available. Stopcock Bore: 2mm or 4mm available

Addition Funnel, High Vacuum Valves, Synthware, Capacity: 100 or 250mL available, Joints: 14/20 or 24/40, High vacuum valve has PTFE O-ring at tip and PTFE wiper to protect Viton O-ring on shaft.

Featuring graduations with a double scale from the PTFE stopcock, these borosilicate glass cylindrical funnels have a pressure equalizing sidearm. Standard Taper outer joint at the top is the same size as the lower Standard Taper inner joint.

Graduated Instatherm® addition funnel provides precise heating for reactor systems demanding heated or constant temperature for the added reactants. Funnels feature standard taper outer top joints and bottom PTFE stopcock inner joints. All funnels include a 9698-20 connecting controller cord.

Addition Funnel, Pressure Equalizing, High Vacuum Valve, Synthware, Capacity: 25-250mL available, Joints: 14/20, 19/22 or 24/40 available, Valve Size: 0-4mm, Valve has extended tip for semi-needle valve adjustment.

Addition Funnel, Pressure Equalizing, PTFE Metering Stopcock, Synthware, Capacity: 10-500mL available, Top Joint (Outer): 14/20, 19/22, and 24/40 available, Bottom Joint (Inner): 14/20, 19/22, and 24/40 available, Stopcock Bore: 2 or 4mm.

KIMAX funnel constructed with heavy uniform walls and strong, fire polished rims and stems to give a long service life. Funnels have a high resistance to chemical attack, mechanical, and thermal shock. Designed from ASTM Specification E1095, Type I, Class B requirements.

PTFE stopcock Graduated with double white ceramic enamel scale; right side ascends and left side descends Calibrated to contain With replacement stopper Designed from ASTM Specification E1096, Type 1C requirements Manufactured from 33 expansion, low extractable borosilicate glass…

Permits solutions to be prepared with No. 13654-24 Stirring Magnet and added portion wise. The T-bore stopcock in the equalizing arm permits isolation of the contents for storage. Capacity, 100 or 250mL. Lower threaded stopcock is all PTFE. Outer joint is standard taper 14/20 or 24/25, inner joint…

Graduated addition funnels similar to 7268 series, except with outside jacket for cooling and/or heating. Jacket extends from just below shoulder of vessel down to the bottom tube just below the stopcock. Stopcock is either 2 or 4mm bore PTFE plug. Bot

Design of funnel permits addition of solvents to flash chromatography columns without disturbing the silica-gel / packing layer. Lower end of the funnel is closed and the stem has a series of small holes through which the solvent drains. Top of the funnel is 75mm (3in) in diameter with the stem size…

…PTFE auger delivers powders at a uniform rate. The 250 and 500mL capacities have the larger, deep cut auger (Size B) for use with coarse material. Funnel has a lower inner joint and top outer, both being the size listed. CG-1723-20 PTFE Auger Size "A" has Internal O-rings Only on the…

Cylindrical shape addition funnel with PTFE stopcocks. For replacement stoppers see CG-3000.

Graduated addition funnel featuring standard taper joints,graduations in both ascending and descending volume,protected drip tip and a glass stopcock. Graduations are calibrated from the stopcock.

Cylindrical style addition funnel with a threaded, grease-free extended tip valve. Design of all PTFE plug permits semi-needle valve action. With a standard taper top outer joint and lower inner joint, both being the same size, and pressure equalizing arm. Funnels with 14/20 and 19/22 joints are…

Cylindrical style addition funnel with a standard taper top outer joint and lower inner joint, both being the same size. With pressure equalizing arm and glass stopcock. Funnels with 14/20 and 19/22 joints are supplied complete with a stopper. For replacement stoppers see CG-3000.

Cylindrical style addition funnel with a standard taper top outer joint and lower inner joint, both being the same size. With pressure equalizing arm and PTFE stopcock. Funnels with 14/20 and 19/22 joints are supplied complete with a stopper. For replacement stoppers see CG-3000.

Double scale graduated funnel with jacket for cooling with dry ice. Calibrated from stopcock. With 1:5 PTFE stopcock plug; for extra plugs, see 8224. For stoppers, order 8250-12.

Cylindrical with joint at top and bottom, drip stem, and double scale graduations, calibrated from stopcock. Drip stem does not extend beyond the joint, thereby eliminating a possible source of breakage. PTFE or metering valve stopcock plug.

Cylindrical with joint at top and bottom, drip stem, and double scale graduations, calibrated from stopcock. Drip stem does not extend beyond the joint, thereby eliminating a possible source of breakage. Metering valve stopcock plug.

Cylindrical with joint at top and bottom, drip stem, and double scale graduations, calibrated from stopcock. Drip stem does not extend beyond the joint, thereby eliminating a possible source of breakage. PTFE stopcock plug.