24 40 Adapters

…connection of standard laboratory dram sample vials directly to the vapor tube or a bump trap of a rotary evaporator. Adapters have a top outer joint of the listed size and a 20-400 G.P.I. thread at the bottom. A PTFE-lined, polypropylene, double-threaded connector attaches the vial to the adapter.

PTFE adapter, precision made, for use when making NPT thread connectors to Ace-Threds. One end designed to make leaktight seal with Ace-Thred without use of O-Rings, other end accepts NPT male thread. Can be used when making connection at top of rapid prep columns or rigid connection between…

…adapter for use with a 24/40 outer joint on the reaction kettle lid. Adapter is supplied complete with a 90° bore valve enabling connection to a luer type syringe for product sampling. Adapter has three inlets for use with 1/8” OD PTFE tubing or optional 5mm OD silicone septa. Adapter and…

Borosilicate glass transition adapter to convert beaded pipe 2 to standard taper joint.

…bushing adapter has a male Ace-Thred connection at bottom and a female NPT thread drilled into the center of the top of the bushing. The top FNPT connection matches male Swagelok fittings and facilitates joining plastic or metal tubing to Ace-Thred glass fittings and adapters. This adapter is…

Adapter with ground joint at bottom and either a #11, #15, #25 or #36 Ace-Thred at top.,/p>

Comes with Synthware Distilling Adapter (Joints: 14/20, 19/22 AND 24/40) and Cow Receivers (Joints: 14/20, 19/22, AND 24/40). Rotating cow receiver allows four flasks to be progressively filled. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

…at top 24/40 inner joint at bottom Adapter, 105°, Standard Taper Joint (3941R23) Arms are approximately 105° apart Upper arm is equipped with an outer Standard Taper joint Lower end is cut off at an angle and is used as a receiver adapter Tube O.D. is 12 mm.

Glass standard taper and spherical joint adapters featuring right angle tee ground glass sidearms. The sidearms are used to make tube compression fitting connections to a wide variety of flexible and rigid tubing using our 12709,12711,12715 & 12716 product families of fittings.

…lysis parameters, the samples can be repeatably homogenized in their unthawed state. Most samples can be processed in 40 seconds or less. CoolPrep™ 24 X 2 mL Adapter is ideally suited for extractions of any temperature unstable or sensitive biological compounds such as RNA, siRNA,…

CoolPrep 24 X 2 mL Adapter is a cryogenic adapter which allows simultaneous lysis of 24 x 2 mL samples. Based on passive temperature control technology, the CoolPrep Adapter ensures an efficient cooling of the samples as dry-ice, placed into the moving tray, is in direct contact with the sample…

This precision-engineered adapter may be cut with a fine-tooth saw or sharp knife into various adapters, such as individual bushings, stirrer bearings, thermometer and gas inlet tube supports, drip-tips, funnels, trap connectors for tubing, etc. Forms a continuous standard taper inside and…

…unthawed state. A wide range of disposable 50 mL Lysing Matrix tubes ensure thorough homogenization of any sample type in 40 seconds or less. CoolBigPrep™ 2 X 50 mL Adapter is ideally suited for extractions of any temperature unstable or sensitive biological compounds such as RNA, siRNA,…

With standard taper top outer and lower inner joints with sealed in lower tube extending below inner joint. Tubing extends 100mm below the joint on the 14/20 and 19/22 sizes and 200mm on the 24/40, 29/26 and 29/42 sizes. Serrated hose connection having an O.D. of 10mm at the largest serration for…

…and performance for the lysis of biological samples. Simultaneous homogenization of up to 24 samples takes place within 40 seconds. * Thorough and quick lysis of any tissues and cells *9 interchangeable adapters allows a unique versatility in sample number, size and temperature conditions

pH probe adapter tube extends the probe deep within large capacity flasks. Fits in 45/50 opening on head and is vertically adjustable along its length. Available with either Chemraz or Fetfe o-rings and in 24 in(61cm), 36 in (91cm), or 48 in (122cm) le

304 Stainless Steel NW flange adapters for use with circulators. Connections either terminate in M16x1, M24x1.5, or M30x1.5 male. There is no need for thread sealent or teflon tape. Connections only need to be hand tightened then given a 1/4 turn with a wrench. Compatabile with all circulator…

Glass standard taper and spherical joint adapters featuring a right angle ground glass sidearm. The sidearm is used to make tube compression fitting connection to a wide variety of flexible and rigid tubing using our 12709,12711,12715 & 12716 product families of fittings.

Glass standard taper and spherical joint adapters featuring a vertical ground glass sidearm. The sidearm is used to make tube compression fitting connection to a wide variety of flexible and rigid tubing using our 12709,12711,12715 & 12716 product families of fittings.

Chart papers in 24 hr, 7 day or 31 day lengths Replacement pens for recording temperature and/or humidity AC adapter

Economical umbrella design freeze drying apparatus utilizing Ace-Threds for positive, grease-free connections that are easy to manipulate. A variety of vessels and adapters available and are readily adapted to mechanical units.

…with #15 o-ring joint ends. Available with 3 or 4 high vacuum stopcock ports. Order with inner joint port ends (14/20 or 24/40) or #15 o-ring joints. The distance between ports is 95mm, ideal for flasks up to 250mL. Please see our various o-ring joint adapters such as Ace codes 5127, 5128 and 5129.

…35/20 ball joint ends. Available with 3 or 4 high vacuum stopcock ports. Order with inner joint port ends (14/20 or 24/40) or #15 o-ring joints. The distance between the ports is 95mm, ideal for flasks up to 250mL. Please see our various o-ring joint adapters such as Ace codes 5127, 5128 and 5129.

…a nylon adapter with a one piece collar for attachment to 10, 19, 25.4 and 30mm stir shafts. Upper adapters permit the coupling to be used with a standard Jacobs style 3-jaw chuck or motors having shaft diameters of 5/16”, 3/8”, 12mm, 1/2”, 5/8” or 3/4”. Adapter is also…

The barrel pump's universal adapter fits onto container openings of 30 - 70 mm, closing tightly. The container screw joints can be screwed into the container with the 3/4" thread and lock nut. The gas-tight barrel pump enables odour-free transfer. During transfer with normal…

…biological laboratories. The system consists of a polypropylene filter funnel with a 10 or 40 micron polyethylene fritted disc, a CG-1049-J style glass vacuum adapter, and a flask or vial. The CG-1049-J vacuum adapters are specially designed so that the vacuum can be controlled using a PTFE stopcock…

…dishes or plates RNase, DNase, pyrogen and cytotoxin free Sterile (gamma) and individually packed Designed for use with 50mL tubes Adapters for 15mL and 5mL tubes included Aseptic outer casing - no need to touch sample surfaces The SureStrain™ Premium Cell Strainer…

…vacuum jacketed, unsilvered. Allihn condenser is 250mm. Adapter at top has two hose connections for maintaining inert atmosphere. Stopcocks are 2mm bore PTFE. Joint on lower drain arm is 14/20, all others 24/40. Complete unit consists of adapter, condenser, storage head, column, flask and mantle.…

…connects between column and flow control adap-ter. Joints on column, reservoir and adapter are 24/40 or 45/50. Columns available with or without Por. B (70-100m) sealed-in fritted disc. Joint clamps also available. Complete item consists of column, reservoir, flow control adapter and clamp.

…with bulb type condenser and one flask. Cycling rates may be doubled over conventional style extractors. All joints are interchangeable. The 82" size is supplied with adapter for connecting the extractor and condenser. This is necessary because of the extremely large top joint on the extractor.

…. . . . . . . . . . . . . . 2 Clamp for Jointed Glassware, Plastic, size 24 . . . . . . . . . . . . . . . . . . . . 8 Clamp for Jointed Glassware, Plastic, size 34 . . . . . . . . . . . . . . . . . . . . 2 Adapter Inlet, Thermometer, 24/40 . . . . . . . . . . . . . . . . . . . . . . . . . .…