24/40 Adapter

Compare Tool

Select up to 3 products

24/40 Adapter
1 - 32 of 84
  • Adapter Vacuum ST 24/40

    DWK Life Sciences (Kimble)

    Vertical adapter with vacuum take-off and drip tip.

  • Adapter 14/20 O X 24/40

    DWK Life Sciences (Kimble)

    For enlarging the size of Standard Taper glass joints. Outer joint is at the top, inner at the bottom Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type 1 and ASTM E438, Type 1, Class A requirements

  • Adapter Univ Sz 21 24/40

    DWK Life Sciences (Kimble)

    For use with plain thermometers, pipets, syringes or other small items with an OD from 2 to 17 mm. A vacuum-tight seal is created with the open top compression cap and FKM o-ring to allow adjustable immersion of thermometers Cap is suitable for use to 150 °C To use it as a septum…

  • These PYREX® angle connecting adapters have a sidearm at an approximately 120° angle from the lower joint. The lower end is equipped with an inner 24/40 Standard Taper joint, and the upper end and sidearm with an outer 24/40 Standard Taper joint. This tube is also a replacement part for…

  • Fused-silica Adapters allow connection of fused-silica to unions, valve ports, and reducers.

  • Fused Silica Adapter Replacement Liner, Inner Diameter: 0.6mm to 0.8mm, Column Inner Diameter: 0.53mm, 1/16in

  • For use with FA-45-24-11 fixed-angle rotor. Accessory for Eppendorf personal microcentrifuges MiniSpin and MiniSpin Plus Adapter for 0.5mL microcentrifuge tubes and 0.6mL microtainers

  • Tube 24/40


    These PYREX® connecting distilling tube adapters have full-length inner 24/40 Standard Taper joints of same size. The connecting arm is approximately at a 75° angle from vertical and is 200mm long.

  • Tube 24/40


    These PYREX® thermometer adapters have a 24/40 Standard Taper ground joint at one end while the other end is tooled to accommodate a thermometer. The adapter comes with a rubber thermometer holder. For replacement rubber thermometer holders, see No. 7715 (0319W06). This tube is also a…

  • Full size 24/40 jointed, low holdup, short path still, original plain version or jacketed with indents. Extension tube from still body allows positioning of drop directly over receiver flask. Gas inlet tube is positioned in distillation flask with 5028 Adapter and secured with a #7 Ace-Thred.…

  • …or 4 port configuration with 4mm double oblique stopcocks. Can be ordered with 14/20, 24/40 inner joints or #15 o-ring joints on each port. Distance between ports is 210MM which will allow for flasks up to 3 Liters. Please see our various o-ring joint adapters such as Ace codes 5127, 5128 and 5129.

  • …up to 121°C (250°F) A few of the many uses: (A) 35/50 to 30/50 (accommodates 34/45 to 29/42) (B) 30/50 to 25/50 (accommodates 29/42 to 24/40) (C) 25/50 to 20/50 (accommodates 24/40 to 19/38) (D) 20/50 to 15/50 (accommodates 19/38 to 14/35) (E) 15/50 to 10/50…

  • Ai 24/40 standard taper joint, heavy wall single cow distribution adapter, with one 3/8" hose barb vacuum port.

  • Ai 24/40 standard taper joint, heavy wall cow type distribution adapter, with three receivers 45° apart, and one 3/8" hose barb vacuum port.

  • These PYREX(r) pear-shaped boiling flasks have full length outer 24/40 Standard Taper joints and are manufactured from No. 7740 borosilicate glass. Wall thicknesses are carefully controlled to provide the proper balance between thermal expansion and mechanical strength for greater shock resistance.…

  • Rotating distillation receiver allows four fractions to be collected. Vacuum adapter has a vertical orientation.

  • Adapter, #15 O-ring joint to 14/20, 19/22 or 24/40 inner joint

  • These 250mL PYREX(r) low actinic flat bottom boiling flasks have full length outer 24/40 Standard Taper joints, but with shorter necks. Low actinic stained glass provides protection for materials sensitive to light. The protective color is an integral part of the flask, which retains the mechanical…

  • Glass Vacuum Adapters

    United Scientific Supplies

    Vacuum adapters have 24/40 joints. Bent adapter has a 105° angle between the top outer joint and bottom inner joint. Straight adapter has a top outer joint and bottom inner joint. Both adapters have 24/40 joints and include a 3/8" hose connector.

  • Adapter, U

    Ace Glass

    Adapter with standard taper outer 24/40 joints.

  • 3-Way Adapters

    United Scientific Supplies

    3-Way adapter has a 75° angle sidearm with inner joints on the sidearm and bottom and an outer joint on the top. Inclined adapter has a 105° angle sidearm with outer joints on the sidearm and top and an inner joint on the bottom. Both adapters have 24/40 joints.

  • …best sealing and the threaded polypropylene extracting nut ensures effortless removal. NOT autoclavable Safely and securely positions glass tubing in a 24/40 joint. Available for 8 and 10mm diameter glass tubing Inert Teflon® PTFE adapter Joint Size: 24/40 Hole Opening: 8mm

  • Adapter, Pouring

    Ace Glass

    Convenient adapter with 24/40 standard joint on end, pour out on the other. For pouring from flasks or funnel without pouring over ground joint.

  • …excellent for controlled evaporation of foaming solvents during rotary evaporation. Complete code supplied complete with PTFE GL80 to 24/40 adapter (CG-1512-X-20). PTFE adapter has FDA grade silicone gasket behind a PTFE envelope type seal so that liquid or powders are only exposed to glass or PTFE.

  • Sampling adapter available with 14/20 or 24/40 joint at bottom and two septum at top for handling air-sensitive materials. Supplied with two septa. For extra septa, order 9096-32.

  • adapter for use with a 24/40 outer joint on the reaction kettle lid. Adapter is supplied complete with a 90° bore valve enabling connection to a luer type syringe for product sampling. Adapter has three inlets for use with 1/8” OD PTFE tubing or optional 5mm OD silicone septa. Adapter and…

  • 60° angle Three Standard Taper 24/40 joints Approximate length 206 mm This tube is also a replacement for organic chemistry kits. Type I, Class A borosilicate conforming to federal specification DD-G-54 lb and ASTM E 438. Also meets the US Pharmacopoeia specs for Type I borosilicate glass.

  • …condenser, stirrer, etc. from joint, insert sublimation adapter and begin. Coolant connection at top and side vacuum connection are 9.5 mm (3/8") O.D. Vacuum connection is controlled by 1:5 PTFE 2 mm bore stopcock. Adapter supplied with 24/40 joint for use with 250 mL or 500 mL flasks. Other joint…

  • Adapter permits CG-1872 series pH electrode (12mm OD) to be inserted either directly into smaller reactors or down through a CG-1872-B baffle. CG-1872-A-01 compression 24/40 joint adapters are to be used with the CG-1872-01 and CG-1872-02 electrodes/probes. The adapter allows use of these probes…

  • …complete. Adapter can also be connected to any vacuum line having a 24/40 port or used in conjunction with a CG-1014 adapter to connect to hoses. Eliminates the need to transfer samples into a conventional round bottom flask. Joint sizes other than 24/40 are available upon request. Adapter is…

  • Heavy wall column, 4.5" long having a sidearm with a 24/40 outer joint. The 24/40 outer joint can be used with an adapter for connection to vacuum source. Adapter has an overall width of 7".

  • These borosilicate glass adapters feature a 5/16" O.D. hose connection at top and Standard Taper 24/40 on bottom. With a stopcock between joints, model LG-1711 has a 2mm glass plug and LG-1711T has a 2mm PTFE plug.

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.