13 X 100 Tubes

Tube made of polystyrene / Cap made of polyethylene. These 8 ml screw cap tubes are available either sterile or non sterile. A special tamper evident cap is offered for applications needing the utmost security where sample integrity is of high importance. Tubes are made of optically clear…

This 13 x 100mm polystyrene test tube has a capacity of 7ml. Tube features a round bottom and includes a hollow top plug cap made of polypropylene. Sold as a pack of 100 tubes.

…50-place rack will hold your 12 x 75 mm and 13 x 100 mm tubes securely in place thanks to silicone tabs surrounding the base of each tube while in the rack. This makes it very convenient to empty tube content before discarding them. Also great for holding tubes in rack securely in place when in…

Translucent polypropylene tubes, 13 mm x 100 mm, are designed to provide excellent chemical resistance.

…of tubes remain visible and sample can be added to uncapped tubes without stopping the action. Drive base and upper section are coated for resistance to most acids and solvents. Comes with two cartridges; for 12-13 mm and 15-16 mm diameter tubes. Dimensions: 17” W x 7” D x 13 1/2”…

Round bottom, with threaded neck; without marking spot Size 100 x 13 mm takes size 13-415 cap; other sizes take size 15-415 cap Cap is not supplied and must be purchased separately; see 9215F70 series Cases of 1,000 contain 4 packages of 250. Listings indicate length x o.d. in mm.

BD offers a wide array of tubes to meet your specialty testing requirements. 10.0mL, 16 x 100mm Glass with Silicone Coated K₃EDTA (12.15 mg), Red Conventional Closure, Paper Label 7.0mL, 13 x 100mm Glass with Silicone Coated K₃EDTA (12.15 mg),…

…test tubes for general purpose laboratory work Screw caps included for storage and transport. Polystyrene tubes provide clarity and are appropriate for use with mild acidic (except oxidizing acids) or alkali solutions, alcohols (except higher alcohols) and salt. Polypropylene tubes are more…

Translucent polypropylene tubes, 13 mm x 100 mm, are designed to provide excellent chemical resistance.

…with Standard Taper solid ground glass stoppers Tubes have a sand-blasted spot for marking 100 x 13 mm size test tubes include No. 9 Standard Taper stopper; 150 x 16 and 150 x 19, No. 13; 175 x 22 and 200 x 25, No. 19. Tube length (without stopper) x tube o.d. are shown in table below.

Translucent polypropylene tubes, 13 mm x 100 mm, are designed to provide excellent chemical resistance.

Unique design allows for use as rack or shipping container Holds 48 tubes For use as temperature-safe shipper, use 6391H87 carton and 6106C13 refrigerant pack Measures 330 x 127 x 100 mm (13 x 5 x 4 in.)

…is complete. System includes: GasPak 100 polycarbonate jar (9 x 5 in.); GasPak 100 lid with O-ring gasket (rubber); clamp/thumbscrew assembly; catalyst reaction chamber; two catalyst charges; GasPak 100 rack for 12 x 100 mm culture dish; GasPak tube holder for thirteen 16.5 x 128 mm tubes.

… Will fit into most standard freezer racking 0.2 mL tube (9.5 mm max) version has 169 wells in a 13 x 13 format 0.5 mL tube (12 mm max) version has 100 wells in a 10 x 10 format Complete with well dividers in packs of 10 *Must use tubes capable of being stored at low temperatures.

…Prepared Culture Media. Visually distinct results from purple to yellow in a minimum of 24 hours (Steam / VH2O2) 13 mm x 100 mm flat bottom tubes of Type I borosilicate glass with screw caps Each lot is accompanied by a Certificate of Analysis and is certified with growth…

For fine dispersion. Porous tip approximately 5mm or 7mm O.D. x 10mm. 7mm O.D. Tube fits #7 Ace-Thred. Offered with Porosity A (145-174 micron), Porosity B (70-100 micron), Porosity C (25-50 micron), Porosity D (10-20 micron), or Porosity E (4-8 micron