1.5 Ml Tube

This is a single block, 24 x 1.5 mL tubes, for use with Corning® LSE™ Digital Dry Bath Heater.

…uniform heat. Polypropylene tubes are EtO sterilized. Microcentrifuge 0.5 mL Tubes have a frosted writing area and reliable snap cap. Made of autoclavable polypropylene, these graduated tubes can withstand temperatures up to 121°C. Microcentrifuge 1.5 mL Tubes feature frosted writing…

…microcentrifuge tubes are designed to provide secure, leakproof seals while remaining easy to open. Polypropylene tubes are autoclavable to 120°C at 15 psi for 15 minutes. 1.5 mL tubes are graduated at 0.1, 0.5, 1.0 and 1.5 mL. 2.0 mL are graduated at 0.1, 0.5, 1.0 and 1.5 mL. Assorted…

Screw cap micro tubes working volume: 1.5 ml skirted conical base, with knurling, transparent, cap natural, cap assembled, with printed writing space, with graduations PCR Performance Tested Low protein-binding 100 piece(s)/bag, 1000/case

…All tubes can be decanted simultaneously Low profile: Will not tip over easily Lightweight: Weighs less than two ounces Holds and locks 50 culture tubes securely Holds and locks 30 microcentrifuge and micro blood collecting tubes securely in racks More uniform incubation: Tubes may be…

1.5mL Easy-Click Graduated Microcentrifuge tubes feature a small, easy-to-open cap. Graduated every 100µL for easy volume identification Small cap allows tubes to be spaced closely together in racks and storage boxes Frosted Cap and writing panel allows for an extra writing room and…

…target in the center. The 1.5 mL and 2.0 mL tubes have an additional textured writing surface on the side of the tube. G-Tubes are made of a tough, transparent and specially formulated polypropylene for better sample viewing and overall strength. These tubes are designed with thicker walls…

… The 300D is supplied with s 24 place angle easy access rotor that can accommodate tube sizes of 1.5ml and 2.0ml microcentrifuge tubes. Additional adapters are available for 0.5ml, 0.4ml, and 0.2ml tubes. The rotor is equipped with a cover that easily "snaps" on and off. The 300D is…

…filled tubes Tubes are supported below the lip while conical ends are immersed in water On benchtop, rack legs prevent bottom of tubes from touching bench surface Thaw, cool and incubate samples at elevated or reduced temperatures—tolerates a wide temperature range Tubes are…

Polycarbin’s 1.5 mL microcentrifuge tube is made using 20% post-consumer recycled content, combining high performance with a significantly reduced carbon footprint. Microcentrifuge tubes are certified DNase, RNase, and Pyrogen free.

…blanks to insure uniform shape and greater mechanical strength. The scale and figures are durable white enamel which stand out clearly against the red color-band on these Lifetime Red tubes. The stem is graduated from 0 to 1.5mL in 0.1mL divisions. The body is graduated from 1.5mL to 5mL in 0.5mL

…centrifugation Unique ClickLok™ sealing mechanism Made of highest purity polypropylene Made of polypropylene These 0.6 ml and 1.5 ml graduated rugged tubes are made of laboratory grade polypropylene suitable to withstand the stress of high speed centrifugation up to 20,000g. The…

…easy opening. Marked graduations and frosted labeling panels on tube and cap for easy writing and identification. These Simport centrifuge tubes withstand centrifugal forces of up to 20,000g for the 1.5 ml tube and 5,000g for the 5 ml size. Will withstand extreme temperatures from -90 °C up to…

…and secure positioning of 1.5, 2.0, and 5.0 mL microcentrifuge tubes in automation workflows. The tube is held securely in the open position, with the cap located in the adjacent slot to prevent interference. Two models available: 1.5 and 2.0 mL version holds 24 tubes 5.0 mL version holds 12 tubes

… Microcentrifuge Tube Racks. Polypropylene . Available in Red or Blue. For 1.5 ml micro test tubes. Can accommodate 50 micro tubes with lid open (without interfering) or 100 micro tubes with lid closed or without lids. Racks are stackable even when completely loaded with test tubes.

DNase/RNase-free 1.5 ml microcentrifuge tubes made of durable polypropylene construction.

…x 43mm H (5.08" x 4.15" x 1.70") Available in 2 sizes to hold either 0.5 or 1.5ml tubes. Open sides, ideal for use in a tray of crushed ice. Easy to assemble. 1226C36: holds tubes: 0.5 mL micro, places: 63, rows: 7 x 9 1226C37: holds tubes: 1.5 mL micro, places: 42, rows: 6 x 7

…microcentrifuge tubes For tubes up to 1.5 mL; maximum cut diameter: 9.4 mm (0.370") Retrieve radioactive pellets from the tips of tubes easily without resuspension or the risk of splashed radioactive substances. Can be used with polyethlyene, polypropylene or polyallomer tubes.…

…enables you to see how cold your samples are at a glance. IsoFreeze® color change racks undergo a dramatic change to a contrasting color at 7ºC. Dimensions: 146 × 105 × 70 mm. Tube capacity: 24 x 0.5, 1.5, 2.0 mL snap or screw-cap style tubes. Rack comes with lid.

…Microcentrifuge Tube Racks are available in five models with 6 to 96 wells. An alphanumeric grid allows for indexing rows and columns, therefore facilitating tube location. These racks will hold 1.5 ml and 2.0 ml snap cap Microcentrifuge tubes. They will also accommodate the popular 0.5 ml to 2.0 ml…

…heavy metals into samples Tubes have 25% thicker bottoms to ensure integrity during use Unique ribbed pestle shaft provides precise finger control of homogenization for shear sensitive samples Matched tubes and pestles available in 0.5 ml &1.5 ml sizes Available individually-packaged…

Blue anodized aluminum blocks hold tubes upright and promote conduction of heat or cold from the Temp-Zone area on selected models of Purifier Cell Logic Biosafety Cabinets to help maintain sample temperature. Holds 18 each 1.5 ml microcentrifuge tubes, 10.5 mm in diameter Overall…