1 Ml Microcentrifuge Tube

…Thomas microcentrifuge tubes are designed to provide secure, leakproof seals while remaining easy to open. Polypropylene tubes are autoclavable to 120°C at 15 psi for 15 minutes. 1.5 mL tubes are graduated at 0.1, 0.5, 1.0 and 1.5 mL. 2.0 mL are graduated at 0.1, 0.5, 1.0 and 1.5 mL. …

Tested to 20,000 RCF Graduated at 0.1, 0.5, 1.0 and 1.5 mL Leakproof lid is easily pierced Frosted writing surface for easy identification Capacity 1.5 mL

…quality, virgin, single melt polypropylene Our latest Posi-Click design incorporates over 20 improvements that have made these tubes our #1 seller. The tubes seal easily with a distinct "click" and stay closed through incubation, freezing and boiling procedures. The unique closure…

Electronic locks. Centrifugation only when the lid is locked. The lid opens automatically after centrifugation. Fast Lifting Speed, The electronic brake Low Noise Capacitive touchpad, responsive. LCD display. Real-time display of speed, time and operating status. Centrifugal time and…

Made of high impact polystyrene This microcentrifuge tube storage box with a polyurethane foam insert is ideal for holding up to 64 tubes from 0.5 ml to 2 ml. It should be used within a temperature range of -90 °C to 80 °C. A transparent cover allows you to see the contents of the box, and…

Polypropylene (PP) Reversible 96-well rack in an 8 x 12 format One side holds 1.5 mL, 1.8 mL, or 2.0 mL microcentrifuge tubes; the other side holds 0.5 mL tubes Alpha-numerically labeled, stackable, autoclavable

… Microcentrifuge tubes are designed to provide secure, leakproof seals while remaining easy to open. Polypropylene tubes are autoclavable to 120°C at 15 psi for 15 minutes. 0.6 mL tubes are graduated at 0.2, 0.4 and 0.6 mL. 2.0 mL are graduated at 0.1, 0.5, 1.0 and 1.5 mL. Assorted…

Feature screw caps that provide a tight secure seal Sterile Attached cap with black silicone O-ring Withstands a maximum RCF of 20,000 x g

Blue anodized aluminum blocks hold tubes upright and promote conduction of heat or cold from the Temp-Zone area on selected models of Purifier Cell Logic Biosafety Cabinets to help maintain sample temperature. Holds 96 each 1.5 ml microcentrifuge tubes, 10.5 mm in diameter

0.5, 1.5 or 2.0 mL capacities Clear or amber Conical bottoms or freestanding Conical microcentrifuge tubes are made from a crystal clear resin that allows users to easily view samples. Polypropylene tubes are suitable for vapor phase liquid nitrogen storage, boiling and…

…screw cap microcentrifuge tubes are pre-assembled with non-looped caps with O-Rings.Colored-cap versions are also available in sterile format. Graduation marks at 1.0 mL intervals Large, frosted writing area for sample identification      Secure fit between tube and cap…

…tubes are available in three sizes; 0.5ml, 1.5ml and 2.0ml. CELLTREAT Micro Centrifuge tubes have an attached flat top cap, engraved graduations and are manufactured from high quality polypropylene. The tubes have a temperature range of -80°C to 120°C. CELLTREAT Micro Centrifuge tubes have a…

SuperSpin™ tubes feature an extra-thick and durable wall that can withstand centrifugation to 40,000 x G. The ultra-clear polypropylene resin gives you a clear view of the pellet as well as correct color rendition. Designed with ergonomic caps and smooth surfaces that make this tube easy to…

Electronic locks. Centrifugation only when the lid is locked. The lid opens automatically after centrifugation. Fast Lifting Speed, The electronic brake Low Noise Capacitive touchpad, responsive. LCD display. Real-time display of speed, time and operating status. Centrifugal time and…

…centrifugation Unique ClickLok™ sealing mechanism Made of highest purity polypropylene Made of polypropylene These 0.6 ml and 1.5 ml graduated rugged tubes are made of laboratory grade polypropylene suitable to withstand the stress of high speed centrifugation up to 20,000g. The…

The myFuge™ 5 microcentrifuge includes a four position rotor for compatibilty with a variety of 5ml test tubes, including 5ml snap cap centrifuge tubes. In addition, this combination rotor has four additional slots for centrifuging standard microtubes (1.5/2.0ml). Simply close the lid and the…

These Costar® 0.65mL microcentrifuge tubes are made of colored polypropylene and are certified RNase-/DNase-free. Rainbow pack includes one bag each of blue, green, yellow, red and orange tubes. Supplied nonsterile and are autoclavable. External graduations and frosted writing spot for easy…

The Flipper microtube rack is designed to hold either 96 0.5 mL or 96 1.5/2.0 mL style microcentrifuge tubes. Rack is reversible with one side suitable for larger tubes and the other side for smaller tubes. The Flipper is fitted with a clear polypropylene lid and both sides are labeled in…

Manual mode & automatic mode. Fast heating, with overheat protection switch to prevent overheating. Display setting parameters and real-time parameters simultaneously, easy to observe and use.

…Microcentrifuge Tube Racks are available in five models with 6 to 96 wells. An alphanumeric grid allows for indexing rows and columns, therefore facilitating tube location. These racks will hold 1.5 ml and 2.0 ml snap cap Microcentrifuge tubes. They will also accommodate the popular 0.5 ml to 2.0 ml…

…a mixed test tube rack, supporting 0.5 to 50 ml test tubes. Additionally 8 optional racks are available, to satisfy your specific laboratory needs. Outfitted with 2 vortex frequencies, this powerful mixer is capable of simultaneously vortex-mixing up to 44 micro-centrifuge tubes. 3 Custom Modes…

Anodized aluminum block with 12 bore holes that accommodate 1.7 ml microcentrifuge tubes. Holder may be placed on any flat freeze drying surface such as inside Clear Chambers, Heated Drying Chambers or the built-in vacuum drying chamber of FreeZone Console Systems; or on FreeZone Stoppering or Bulk…

…Tube is made of inert virgin-polypropylene copolymer, to minimize the risk of altering samples Universal use - Accommodates all fixed angle head microcentrifuges (0.5ml and 2.0ml upright models require adapter Cat. No. 4212). Will withstand maximum G-forces of all current microcentrifuge…

… Quiet and cool running Complete with easy access, 24 x 1.5/2.0 ml rotor Loaded with features, the Spectrafuge 24D has precise digital microprocessor control and an innovative rotor design. The rotor places tubes on a plateau, where the user can easily grip the tops. A powerful and quiet…

…digitally controlled multi-speed microcentrifuge, includes a pulse feature for short spins High capacity 16 position rotor receives 1.5 or 2.0 ml tubes, each hole is clearly marked by numbers Easy to read graphics indicating RPM and RCF Easyload rotor permits tubes to be loaded vertically,…

…low profile tubes. In terms of evaporation, loss of PCR volume is less than 3%. These tubes are highly transparent, thus, making them ideal for applications where the optical qPCR signal is obtained through the bottom of the tube. Capp 0.1 mL tubes can be ordered as individual tubes with caps and…

…2.0 mL tube capacity Axygen Microcentrifuge Tube Rack Axygen Microcentrifuge Tube Rack is molded from durable, autoclavable polypropylene, and features non-skid rubber feet. The rack has two levels and exhibits wide spacing to provide prime sample access and visibility. Tube positions…

…anodized aluminum blocks hold tubes upright and promote conduction of heat or cold from the Temp-Zone area on selected models of Purifier Cell Logic Biosafety Cabinets to help maintain sample temperature. Holds 96 each 0.5 ml microcentrifuge tubes, 7.5 mm in diameter Overall dimensions…

Blue anodized aluminum blocks hold tubes upright and promote conduction of heat or cold from the Temp-Zone area on selected models of Purifier Cell Logic Biosafety Cabinets to help maintain sample temperature. Holds 18 each 1.5 ml microcentrifuge tubes, 10.5 mm in diameter Overall…

…anodized aluminum blocks hold tubes upright and promote conduction of heat or cold from the Temp-Zone area on selected models of Purifier Cell Logic Biosafety Cabinets to help maintain sample temperature. Holds 18 each 0.5 ml microcentrifuge tubes, 7.5 mm in diameter Overall dimensions…

Reduced noise Single rotor Speeds to 14,000 rpm The centrifuge 5418 is an 18-place microcentrifuge for 1.5/2.0 mL tubes. The 5418 can reach a maximum rcf of 16,873 x g/14,000 rpm. Design allows safe centrifugation of hazardous materials. High speed motors generate g-force…

…Ducting system supplies a continuous flow of ambient air to the rotor chamber to keep the rotor cool and to prevent significant rises in sample temperature. Complete and ready to operate unit includes a 18 x 1.5/2.0 mL rotor. Adapters are available for 500, 450, 250 and 200 µL cycling tubes.