Size: 75 mm long x 12 mm o.d.; capacity: 5 mL Designed for economical, one-time use Clear polystyrene, with deep, friction fit caps of lower density polyethylene Caps allow sealing or partial closure to permit gas transfer 9219F22 tubes are packed in bags of 25; case contains 20…

Corning Cell Strainers are an easy and ready-to-use solution for obtaining a more uniform single cell suspension Nylon mesh provides a strong, uniform filtration device Strainers reduce chance of contamination Cell strainers fit inside a Falcon®™ 50 mL centrifuge tube.…

These PYREX® culture tubes are supplied with phenolic caps to facilitate handling and sealing after autoclaving. Caps are fabricated from a special formula resistant to the effects of temperature and steam in autoclaving and are provided with a glued-in, white rubber liner. The white enamel…

With lip Tubes 10 mm through 18 mm o.d. have marking spot. Listings indicate length x o.d. in mm.

Single use culture tubes are housed in easy-to-open, easy-to-use packaging. The three small sizes come in a dispenser arrangement while the larger sizes are bulk-packed. Culture tubes are made of borosilicate glass to reduce pH changes and contaminants that could potentially leach from…

These 15mL PYREX® conical centrifuge tubes have white enamel graduations for durability. The 15mL size is graduated upward from the tip in 0.1mL divisions. The 50mL size is graduated upward from tip to 10mL in 0.5mL divisions, and from 10 to 50mL in 1mL divisions. The phenolic 15-415 GPI…

Unattached HDPE rim seal caps provide a tight secure seal Polypropylene Self-standing Sterile Withstands a maximum RCF of 20,000 xg

These Costar® 1.7mL low binding microcentrifuge tubes feature a bonded polymer technology that reduces protein and nucleic acid binding, resulting in better sample recovery. They are made of natural (uncolored) polypropylene and are certified RNase-/DNase-free. -Supplied nonsterile and are…

Graduated Capacity 50 mL Tube has white enamel graduations upward from tip to 10 mL in 0.5 mL divisions and from 10 to 50 mL in 1 mL divisions Tube length is 135 mm, o.d. 28 mm Round bottom tube with pour out spout for easy decanting Wall thickness approximately 1.5 mm; length…

Round bottom, with threaded neck; without marking spot Size 100 x 13 mm takes size 13-415 cap; other sizes take size 15-415 cap Cap is not supplied and must be purchased separately; see 9215F70 series Cases of 1,000 contain 4 packages of 250. Listings indicate length x o.d. in mm.

Fabricated from specially selected tubing for product durability. Engraved white-filled graduations at 25 and 50 mL .

These PYREX® ignition tubes are made from No. 7740 glass and are satisfactory for most applications encountered in school work where temperatures above 600°C are not required. These rimless tubes perform well when continually used at temperatures up to 500°C, or for short periods to 600°C.

Graduated Capacity 5 mL in 0.1 mL divisions, with conical tip and Standard Taper 9 ground glass stopper, Thomas number 8770J22 Length including stopper, 140 mm; o.d. 13.5 mm

These 15mL PYREX® conical centrifuge tubes have white enamel graduations. The 15mL sizes are graduated upward from tip in 0.1mL divisions.

Corning® 50mL clear polypropylene (PP) preassembled closed systems self-standing centrifuge tubes come with the advanced polyethylene CentriStar™ caps. The CentriStar™ cap has an easy-on/easy-off flat top and offers advanced ergonomics with its wider knurls and roll-over edge design…

This specially designed PYREX® inlet tube is a replacement part for the PYREX® Cyanide Distilling Apparatus (No. 3350-C) Used in testing for soluble and insoluble cyanides in water. Cyanide as hydrocyanic acid (HCN) is released from cyanide complexes by means of a reflux-distillation…

These disposable Corning® caps are made from phenolic resin and are autoclavable at 121°C. Caps are provided with a white rubber liner.

Corning offers a full line of disposable, premium quality conical centrifuge tubes manufactured from high quality, ultra-clear resins. These tubes meet the quality and performance standards demanded by researchers. High Speed 15 mL and 50 mL tubes Rated up to 17,000 RCF 95kPA (14…

Without stopper, pear shaped 58 mm o.d. x 159 mm long Lower stem graduations: graduated upward from 0 to 1 mL in .05 mL divisions Bulb graduations:  from 1 to 5 mL in 1 mL   from 5 to 50 mL in 5 mL   from 50 to 100 mL in 10 mL divisions

These heavy duty 10mL PYREX® conical centrifuge tubes are made with increased wall thickness for greater mechanical strength. In order to conform to outside diameter and overall length limitations imposed by centrifuge rotors and supports, it has been necessary to reduce the capacity of these…

These PYREX® replacement tubes fit the Kuderna Danish Apparatus and have an outer 19/22 Standard Taper joint. The tube graduations go from 0 to 2mL in 0.1mL increments and from 3mL on in 1.0mL increments.

These 50mL PYREX® conical centrifuge tubes have white enamel graduations and are graduated upward from tip to 10mL in 0.5mL divisions, and from 10 to 50 in 1mL divisions. The No. 16 Standard Taper pennyhead stopper is solid glass.

These Costar® low binding microcentrifuge tubes feature a bonded polymer technology that reduces protein and nucleic acid binding, resulting in better sample recovery. They are made of natural (uncolored) polypropylene and are certified RNase-/DNase-free. -Supplied nonsterile and are…

These 100mL PYREX® conical centrifuge tubes have white graduations and are used in accordance with standard methods of testing for water and sediment in petroleum products. These tubes are graduated upward to 0.5mL in divisions of 0.05mL; from 0.5mL to 2mL in divisions of 0.1mL; from 2mL to 3mL…

0.2mL PCR tubes (assorted colors) are made of thin wall polypropylene and designed for precise fit in heat blocks to optimize heat transfer With domed cap for efficient heat transfer Nonsterile and certified DNase- and RNase-free Autoclavable at 121°C and will withstand…

These disposable 20x125mm PYREX® culture tubes have a round bottom, GPI 18-415 threads and come without a marking spot. They are designed for both tissue culture and general bacteriological work. These tubes hold approximately 24 mL, are made from borosilicate glass, bulk-packed and are sold…

These disposable 20x150mm PYREX® culture tubes have a round bottom, GPI 18-415 threads and come without a marking spot. They are designed for both tissue culture and general bacteriological work. These tubes hold approximately 30mL, are made from borosilicate glass, bulk-packed and are sold…

These reusable PYREX® rimless culture tubes offer greater convenience in plugging and rack storage. Walls and bottoms are of uniform thickness. Ends are fire-polished.

Graduated upward to 0.5 mL in divisions of 0.05 mL , from 0.5mL to 3mL in 0.1 mL divisions, from 3 mL to 5 mL in 0.5 mL divisions and from 5 mL to 100 mL in 1 mL divisions. Made with a 3 mm vent hole located 180° from the front of the tube. Tubes are for testing propane, butane and Isobutane mixtures.

Reusable PYREX rimless culture tubes offer greater convenience in plugging and rack storage. Ends are fire-polished. The 22 and 25mm o.d. tubes do not have marking spots.

Identical to 9215F20 series, but with marking spot Cap not included Disposable Pyrex® culture tubes have a round bottom and come with a white marking spot. These tubes are designed for both tissue culture and general bacteriological work. These tubes are made from borosilicate glass,…