Microtube, 0.65mL, RED/PINK PK/1000

Size: 75 mm long x 12 mm o.d.; capacity: 5 mL Designed for economical, one-time use Clear polystyrene, with deep, friction fit caps of lower density polyethylene Caps allow sealing or partial closure to permit gas transfer 9219F22 tubes are packed in bags of 25; case contains 20…

These disposable standard and semi-micro cuvettes are designed for use in spectrophotometers. They are produced from either optical polystyrene or UV grade PMMA and include optical windows for optimum transmittance through spectrum range from 340 to 800nm for the optical polystyrene and from…

Corning Cell Strainers are an easy and ready-to-use solution for obtaining a more uniform single cell suspension Nylon mesh provides a strong, uniform filtration device Strainers reduce chance of contamination Cell strainers fit inside a Falcon®™ 50 mL centrifuge tube.…

100% Plastic microhematocrit capillary tubes Plain untreated Globe Scientific's plastic micro hematocrit capillary tubes are completely unbreakable. They eliminate the risk of injury and contamination associated with glass tubes due to breakage. The tubes are packaged 100 per vial,…

BD Vacutainer® spray-coated EDTA Tubes are used for whole blood hematology determinations, immunohematology testing and blood donor screening.* * The performance characteristics of these tubes have not been established for infectious disease testing in general; therefore, users must…

Transport Tubes Tube is polypropylene (PP) - Screw cap is Polyethylene (PE) Tube is self-standing with conical bottom Molded graduations Clear: 1224L57-L58 Amber: 1224L59 Dimensions: 16mm x 56mm (1224L57) Dimensions: 16mm x 92mm (1224L58-L59) Universal Tubes …

125 x 8 Fits most popular thermal cyclers RNase/DNase and Pyrogen free Caps included Autoclave Safe Autoclave instructions: Autoclave at 121°C at 15psi (1 atm) for 15 mins. Do not use drying cycle. Remove from autoclave once temperature has reached at least 80°C.

15mL & 50mL Conical Tubes High-clarity, medical-grade polymer Graduations every 1 mL (15 mL tube) or 5 mL (50 mL tube) increments Rated to 15,000 x G Temperature range: -80° to 40°C Tube racks are recyclable Both 50mL and 15mL tubes are BQ215 presented 25 tubes per…

Fits 13mm glass evacuated blood drawing tubes Fits most 12mm plastic test tubes Dual tabs for easy removal Polyethylene (PE)

These PYREX® culture tubes are supplied with phenolic caps to facilitate handling and sealing after autoclaving. Caps are fabricated from a special formula resistant to the effects of temperature and steam in autoclaving and are provided with a glued-in, white rubber liner. The white enamel…

Globe Scientific is pleased to expand on this line of premium quality microcentrifuge tubes with attached snap caps. The polypropylene (PP) tubes are resistant to most chemical reagents and can be autoclaved at 121°C. Each tube is molded with precise graduation marks for accurate measurements.…

Globe Scientific's plastic culture tubes are produced in polystyrene (PS) or polypropylene (PP). The polystyrene tubes can withstand 1500 RPM during centrifugation. polypropylene tubes can withstand 3000 RPM and are autoclavable and freezable. Tubes with dual position snap caps (LDPE)…

With lip Tubes 10 mm through 18 mm o.d. have marking spot. Listings indicate length x o.d. in mm.

Single use culture tubes are housed in easy-to-open, easy-to-use packaging. The three small sizes come in a dispenser arrangement while the larger sizes are bulk-packed. Culture tubes are made of borosilicate glass to reduce pH changes and contaminants that could potentially leach from…

MicroTube Rack System™ for sample collection, assay, and short or long term storage 0.65, 1.1 and 2.2mL tubes and variety of capping options are available Cost effective Deep-well plate alternative, with removable wells Now available in familiar single pack format

For use as a secondary tube for barcoding on automated analyzers. Popular brands of analyzers include Hitachi®, Olympus®, Corning®, Ortho®, Kodak®, Beckman®, IA®, Tosoh®, Vitros® and more.

These polyropylene microcentrifuge tubes feature attached leak-resistant flat snap caps. Each tube is molded with precise graduation marks for accurate measurements.  Mfr. No. 111562 & 111572 These 1.5mL and 2mL microcentrifuge tubes are lot certified to be RNase free, DNase free,…

Similar to 9385J35, but with one side flattened to keep tube at proper angle during incubation Provides flat surface 5.5 cm 2 for monolayer cultivation of uniform thickness, aiding microscopic examination Tube will accommodate 10 x 20 mm cover slip. Size 110 x 16 mm. Sterilized by gamma…

Polypropylene or polystyrene Standard sizes Sterile or non-sterile Available with or without snap cap Thomas Culture Tubes can be used for almost any laboratory procedure. They are chemically free and biologically inert. These tubes are precision molded from premium grade materials and checked…

Disposable polypropylene tubes and caps with recessed lid and sealing ring to prevent leaking. Frosted writing surface allows for permanent identification and labeling. Autoclavable to 121°C and can be stored in freezers to -80°C. Manufactured in ISO 9001:2000 and 100,000 grade cleanrooms.…

Globe Scientific offers an extensive line of mulit-use test tubes. They are molded from premium grade polystyrene for clarity or of polypropylene for impact strength and stability to common acids, alkalies, and solvents. Polystyrene tubes can withstand 1500 RPM during centrifugation. Polypropylene…

Everyday Use. Solid Performance. Our PerformR® centrifuge tubes combine reliable performance in major centrifuges. Spin rates higher than most popular brands. And high quality lab certified non cyto-toxic medical grade resin. PerformR® tubes can be used in everyday lab work and…

The innovative VACUETTE® Blood Collection Tubes made out of virtually unbreakable PET plastic have set the standard on today‘s market. They provide improved safety and hygiene during specimen collection procedures with the advantage of being as clear as glass. Most VACUETTE® Blood…

Gamma radiation sterilized, Polystyrene or polypropylene construction, Leakproof caps Sterile culture tubes are precision molded from premium-grade, chemically inert plastic materials: polystyrene (PS) for clarity and polypropylene (PP) for toughness and chemical resistance. Polypropylene…

KimCote® plastic-coated culture tube made from tubing with uniform wall thickness for maximum heat transfer and chemical resistance. Thread finish complies with Glass Packaging Institute (GPI) requirements. Cap is not attached. Designed from ASTM E982, Type VI, Class A requirements.

Multiple Uses Ideal for general purpose laboratory work and useful as leak-proof secondary containers for shipping etiological specimens. Freestanding octagonal bases lock into our special tray for one-hand operations. Polypropylene co-polymer (PPC) is nearly transparent and is appropriate…

50mL centrifuge tube, polystyrene (PS) with red screwcap (HDPE) and printed graduations. Available in non-sterile and sterile packaging White graduation marks and writing area

These Oakridge Style Centrifuge Tubes from Globe Scientific are the economic choice for high speed refrigerated or non-refrigerated centrifugation. Molded from durable, chemical resistant polypropylene, the tubes have round bottoms and consistent wall thicknesses for centrifugation at up to 50,000g…

Eppendorf PCR Tubes Manufactured from polypropylene Reduced risk of contamination Available in 0.2 and 0.5 mL sizes 2-part polycarbonate rack consists of work tray and frame for 96 x 0.2 mL PCR tubes All tubes can be directly transferred to the Thermoblock Autoclavable at…

Designed for use with 96 Well Thermal Cyclers Tubes provide optimal contact with the sample block, thus ensuring optimal heat transfer Prevents cross-contamination Provides secure seal for oil-free thermal cycling Individual 0.2mL Thin Wall Tubes require an 8 or 12 Strip Cap to…

These 15mL PYREX® conical centrifuge tubes have white enamel graduations for durability. The 15mL size is graduated upward from the tip in 0.1mL divisions. The 50mL size is graduated upward from tip to 10mL in 0.5mL divisions, and from 10 to 50mL in 1mL divisions. The phenolic 15-415 GPI…