Ace Glass Stirrers
-
Motor, AC variable, hazardous duty, 1/2hp,230/460v 60Hz²3 phase, complete with controller, 115v 50/60Hz input, CE and ²cULus rated. Control box cord to motor is 12ft long, control²box cord to electrial source is 24ft long.
-
Precision ground glass stirring shafts, 10mm OD, paddled, button type and bead type. Button type shafts accept 8083, 8085, 8086, 8087 & 8096 stir blades. Beaded shafts accept 8088, 8089, 8090 & 8091 agitators. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 & 8055.…
-
Stirring Shaft, PTFE Coated Glass, 10mm
Ace GlassPrecision ground glass stirring shafts, 10mm OD, button type, PTFE coating permits higher stirring speeds with Trubore bearings. If used unlubricated, 500 rpm max with water-cooled 8040 bearing. Compatible with 8036, 8038, 8039, 8043, 8047, 8051, 8055 and 13443 bearings. Button type shafts accept…
-
Heavy duty, 28mm O.D. glass stirring shaft for use with ACE 12845 reactors. Shafts are pre-drilled to accommodate 8091,8093 & 8101 agitators for 28mm od shafts. Recommended for use with either our 8067 Trubore™ bearing with debris trap or our 8050 non-shedding bearing. For motor connection,…
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 19mm agitators will fit drilled type or knob type 8076, 8078 and 8079 shafts.
-
Bearing, Trubore, 5 & 6mm
Ace GlassTrubore bearing with standard taper joint for use with our 9534, 9535 and 9541 precision ground stir shafts. Lubricant well at top will accept enough 8117 Stir-Lube to provide hours of operation at up to 1000 rpm. Match bearing ID with stir shaft OD.
-
316 stainless steel, football shaped, stir blades for 10mm OD button type stir shafts. Holed versions, codes -70 thru -74, provide even greater agitation. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
PTFE Gasket
Ace GlassDesigned to fit 8068, 8070, 8071, 8074 or 8078 stirring shafts. Useful as dust cover and as replacement for gasket supplied with 8127 collar. Twelve to a package.
-
Precision ground glass stirring shafts, 19mm OD, hollow, heavy duty. Knob type shafts accept 8091,8092,8093,8100 agitators and can be used in all 19mm ID Trubore 8059, 8060, 8061 and 8065 bearings. Compatible with our 8050 mechanical seal and 13445 PTFE Debris-free bearings. Join to stirrer motor…
-
Bearing, Trubore, Plain, 10mm
Ace GlassInterchangeable bearing designed to be used with our precision ground stirring shafts (8068,8070,8071,8073,9532,9533). Recommended top stirring speed with our 8117 Stir-Lube is 1500 rpm.
-
Agitator, PTFE, 4 Blade
Ace Glass4 Blade PTFE agitator available with either 45 or 90 degree blade angle. For use with glass or metal shafts and is secured using a compression style fitting allowing it to positioned anywhere along the length of the shaft.
-
Stir Shaft, Retreat Agitator, PTFE
Ace GlassPTFE covered stainless steel shaft with a solid PTFE retreat curve agitator. Featuring a retreat angle of 30 degrees and, for a better grip by the stir motor chuck,50mm of exposed stainless.
-
Ultra-Vacuum stirrer bearing for applications up to 0.6 Torr. Non-shedding bearing is manufactured from PTFE, Rulon and PEEK materials. Equally good in both vacuum and pressure applications as low as 0.6 Torr. Rated for up to 400 rpm with both glass (polished rather than precision ground is best)…
-
Chuck, Flex-Grip®
Ace GlassNylon chuck for use with ACE stirring shafts or other shafts of the same dimensions. Chuck has flexible insert which allows for misalignment of shaft without danger of breakage.
-
Agitator, PTFE, Multi-Paddle, 10mm Shaft
Ace GlassPTFE multi-paddle agitator for 10mm OD drilled or knob type shafts. Paddles are replaceable. Fits 10mm OD drilled or knob type 8068, 8071 and 8079 shafts.
-
PTFE covered stainless steel stirring shafts, 10mm OD, drilled type. If used unlubricated, 500 rpm max with water cooled 8040 bearing, 100 rpm max recommended with 8036, 8038, 8039, 8043, 8047, 8051 and 8055 bearings. With condensate film as added heat transfer agent, 2000 rpm can be attained.…
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 76mm long blade will fit through a 29/42 joint. Fits 10mm OD drilled type or beaded type 8068, 8071 and 8075 shafts.
-
Chlorofluorocarbon grease for use at speeds up to 6000 r.p.m. with ACE standard glass assemblies. Use 8040 water-cooled type bearing for long-time stirring (over one hour). Below one hour, 8038 type may be used at 1500 r.p.m.; eight hours at 1000 r.p.m. High chemical inertness unaffected by strong…
-
Bearing, Trubore, Water Cooled, 19mm
Ace GlassTrubore bearing, jacketed, standard taper joint. For use with 8077 & 8078 19mm od precision ground glass shafts or 8079 PTFE covered shafts.
-
PTFE banana shaped stir blades for 10mm OD button type stir shafts. 3mm thick blades have a number of perforations and are designed to closely fit various sizes of round bottom flasks. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.
-
Stirrer, Vacuum, Debris Free
Ace GlassA rugged, compact, inexpensive stirrer. The upper member turns with stirring shaft, bottom member remains stationary. Upper member supplied with vinyl connector. Use with ACE 8134 stirring shafts. Assembly may also be used to make your own rotary evaporator.
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 3.2x15.2cm blade will fit through a 45/50 joint. Fits 19mm od drilled type or knob type 8076, 8078 & 8079 shafts.
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 28mm agitators will fit drilled type 8080 shafts.
-
Fully flexible drive shaft facilitates isolation of the stirrer motor from the reactor. Complete units, code -30 (91.4cm) and code -32 (152.4cm), designed for use with 8mm (5/16in) motor shaft. Purchase the optional code -27 adapter for motors with 9.5mm (3/8in) shafts. Reactor end consists of a…
-
Polished stainless steel stirring shafts, 10mm OD, drilled type with removable button. When used with 8066 PTFE bearing, a lubricant-free vacuum seal can be realized at speeds up to 200 rpm. Recommended for use with 8044,8050,8066,13443 and 13445 bearings. With button, shaft accepts…
-
Bearing, Trubore, High Vacuum, 10mm
Ace GlassThis bearing is the standard liquid seal type except that the use of Trubore tubing enables this unit to perform very satisfactorily under high vacuum conditions. Use our precision ground stirring shafts (8068,8070,8071,8073,9532,9533).
-
Button type, solid glass stirring shafts, 5 & 6mm OD. Precision ground shafts, codes -04 & -06, should be used in matching glass Trubore 9524 and 9527 bearings. Polished shaft, code -40, should be used only in our 8066-120, 6mm PTFE inner bearing. All accept our 9542 blades. Join to stirrer motor…
-
Bearing, Trubore, Water Cooled, 19mm
Ace GlassTrubore bearing, jacketed, spherical joint. Designed to accomodate our 8112-10 packing box. For use with 8077 & 8078 19mm od precision ground glass shafts or 8079 PTFE covered shafts. Spherical joint can be clamped to prevent rotation. Trubore length of 15.2cm or 6 inches.
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8076 (19mm od) or 8080 (28mm od) polished glass stir shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
Agitator, PTFE, Turbine, For 10mm Shaft
Ace GlassAll-PTFE turbine type agitator. Unique locking arrangement assures positive grip. Agitator fits 10 mm shafts. Shaft opening is drilled straight thru to allow positioning of agitator at any drilled position on shaft as well as the bottom. For use with bead type glass shafts, 8068-G, 8075 or PTFE…
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8074 stainless steel or 8075 polished 10mm od glass shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…