Shaft Stirrers
-
Angled Stirrer Blades
ChemglassAgitators are made entirely of PTFE and glass filled PTFE and are for use with 19mm or 25.4mm OD stirrer shaft CG-2097 and are available in 45°, 60° and 90° impeller angles. The 45° and 60° impellers are set up to stir downwards in a clockwise direction and upwards when rotated…
-
PTFE stirrer shaft shaft
MilliporeSigmaStirring shaft with steel core. Use with PTFE stirrer guides and for applications which do not require a guide. Unbreakable, scratch resistant, and usable up to 280C.
-
Tru-Stir Stirrer Shaft Coupling
ChemglassThe unique design of our Tru-Stir™ stirrer shaft coupling eliminates the need to use rubber hose or universal adapters to attach your stirrer shafts to overhead stir motors. Coupling incorporates a unique helical stainless steel spring permitting up to 1/4” of offset misalignment and…
-
Replacement Glass Shaft
ChemglassReplacement components for CLS-1414 and CLS-1415 Spinner Flasks.The Complete Impeller Assembly consists of top cap, silicone liner, glass rod, compression fitting magnet holder, paddle and magnetic stir bar.
-
A 19mm precision ground and polished stirrer shaft to fit CG-2086 19mm PTFE bearings. Side button for attachment of CG-2089 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF GLASS BEARING. FOR GROUND SHAFTS USED WITH GLASS BEARINGS SEE CG-2085. ALSO NOTE:…
-
Button Style 10mm Stirring Shaft
ChemglassA 10mm precision ground stirrer shaft to fit CG-2070 through CG-2072 10mm bearings. Side button for attachment of CG-2080 or CG-2081 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF PTFE BEARING. FOR POLISHED SHAFTS USED WITH PTFE BEARINGS SEE CG-2079.
-
Stirrer Bearings and Shafts
ChemglassHeavy duty 19mm stirrer bearing for use in stirring large volumes under high torque. Bearing has a tooled lubricant cup.PLEASE NOTE: NOT FOR USE WITH CG-2087 or CG-2088 PRECISION GROUND AND POLISHED STIRRER SHAFTS. STIRRER BEARINGS, 19MM, HEAVY DUTY, JACKETED, Similar to CG-2082 but with a water…
-
Stirrer Blades, PTFE
Ace GlassPTFE stir blades for button type stir shafts. 10mm OD shafts can be found in our product series 8068, 8070, 8074 and 8075. 19mm OD shafts can be found in our 8076 and 8077 series.
-
Stirring Blade, For 5 & 6mm Shaft
Ace GlassPTFE stirring blades for use with our button type 9524 and 9527 stirring shafts. Blades are 41mm wide x 12mm high and are designed for use in flasks 250ml and less. Match blade to shaft OD.
-
316 stainless steel, football shaped, stir blades for 10mm OD button type stir shafts. Holed versions, codes -70 thru -74, provide even greater agitation. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
Heavy Duty PTFE 19mm Stirrer Blades
ChemglassStirrer blade made of 3/16" thick solid PTFE for use with both Chem-Stir™ and button style stirring shafts having a 19mm OD.
-
Stirring Shaft, Glass, 19mm, Polished
Ace GlassPolished glass stirring shafts, 19mm OD. Available in solid and hollow styles and in various lengths. Join 8085 blades to button type shafts, Join 8091,8092,8093 and 8100 agitators to either knob or drilled style shafts. Join all shafts to stirrer motor using 8124 series chucks. Recommended for use…
-
Fully flexible drive shaft facilitates isolation of the stirrer motor from the reactor. Complete units, code -30 (91.4cm) and code -32 (152.4cm), designed for use with 8mm (5/16in) motor shaft. Purchase the optional code -27 adapter for motors with 9.5mm (3/8in) shafts. Reactor end consists of a…
-
Precision PTFE covered stainless steel stirring shafts, 19mm OD. Drilled type shafts accept 8091,8092,8093,8100 agitators and can be used in 19mm Trubore bearings (8059, 8060, 8061 & 8065). Not recommended for PTFE bearings 8050, 8067 and 13445. Join to stirrer motor using 8124 series chucks.
-
PTFE screw propeller stirrer
MilliporeSigma•Guaranteed chemically resistant, inert and leak-free •Use up to 280C (540F) •Encapsulated stainless steel core for maximum rigidityPlease note: The propeller and shaft are fused together.
-
PTFE Coated SS Stirring Shafts
Chemglass16mm O.D. shaft is constructed using a molding process whereas the blade is molded directly onto the PTFE coated stainless steel shaft. This makes the stirrer chemically inert, easy to clean and can be used up to 280°C. The top of the shaft has 50mm of exposed 1/2" diameter stainless steel…
-
Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8074 stainless steel or 8075 polished 10mm od glass shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 28mm agitators will fit drilled type 8080 shafts.
-
Precision ground glass stirring shafts, 10mm OD, paddled, button type and bead type. Button type shafts accept 8083, 8085, 8086, 8087 & 8096 stir blades. Beaded shafts accept 8088, 8089, 8090 & 8091 agitators. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 & 8055.…
-
Banana Shaped PTFE Stirrer Blades
ChemglassBlade is shaped to resemble the contour of a round bottom flask. Blades are available solid or perforated. Made of 3/16" PTFE to fit 19mm OD stirrer shafts. Minimum joint size listed is the size required to allow passage of the blade.
-
PTFE Gaskets
ChemglassPTFE gasket is 0.015" thick with an opening to fit Chemglass stirrer shafts. Gasket is placed below the CG-2048 Safety collar to prevent wear as a result of the collar rotating against the stirrer bearing. Also useful as a dust cover.
-
Chem-Stir™ 10mm Stirring Shafts
ChemglassEliminates Flask Breakage: PTFE is the only contact in the lower radius of the flask, therefore breakage due to dropping the stirrer shaft has been eliminated. Eliminates the Frustration of Assembly: Unique design permits the proper amount of tension to be applied to the blade,…
-
1/4 HP Explosion Proof Motor
ChemglassExplosion proof (XP) motor features a 5:1 right angle gearbox to reduce the overall height above support frame to 10.5”. Motor is supplied with a 30ft 18/3 SJEOO cord with twist lock connector. XP motor must be used in conjunction with our digital motor controller, and mounts to all our…
-
Stirrer Blades, PTFE, Oval, 10mm Shafts
Ace GlassPTFE oval stir blades for 10mm OD button type stir shafts. 10mm OD shafts can be found in our 8068, 8070, 8074 and 8075 series.
-
Bearing, Trubore, Water Cooled, 19mm
Ace GlassTrubore bearing, jacketed, standard taper joint. For use with 8077 & 8078 19mm od precision ground glass shafts or 8079 PTFE covered shafts.
-
Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.
-
STIR-LUBE®,Trubore® Stirrer Lubricant
Ace GlassA superior, low melting, silicone base lubricant which liquefies at body temperature. Because of its composition, you need apply only a very thin film of Stir-Lube® to a stirring shaft to increase bearing and shaft life at least three times over that of a bearing lubricated with glycerine.…
-
Chem-Stir™ PTFE Stirrer Bearings
ChemglassGrease-Free PTFE stirrer bearing designed for use under moderate vacuum applications. The bearing consists of a threaded glass adapter having an inner joint, a set of PTFE washer style bearings, a stainless steel spring, nylon alignment ring and Celcon® compression cap. The unique design of…
-
Stirring Shafts
VELPThomas No. 1198F83: Stirring shaft with floating blades: The two blades that open as the speed rises generate an axial flow in the container, from the top towards the bottom. Particularly recommended for stirring in narrow-neck containers, e.g. flasks. Thomas No. 1198F84: Stirring shaft with…
-
Precision ground glass stirring shaft, 10mm OD, attached vanes. Vanes will fit through a 45/50 joint and are contoured for use with our 9448 and 9456 series Mini-Lab flasks. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 and 8055. Compatible with our 8050 mechanical…
-
PTFE, large-scale, multi-paddle agitator design to accept pinned bottom valves, like our 6482 flush-seal valve. The pin helps reduce wobble or flexing at higher rpm. 19mm agitators will fit drilled type or knob type 8076, 8078 and 8079 shafts.
-
Collar, Stir Shaft
Ace GlassDesigned to be used with 8068, 8070, 8071, 8074 or 8078 stirring shafts. Handy for positioning shaft in bearing, and preventing shaft from dropping into flask. Supplied with PTFE gasket to prevent scratching top of bearing and acts as dust cover. Available in either Glass-filled PTFE or 316…