Beaded pipe to sanitary fitting adapter connects to the 1-1/2” beaded pipe side arm of CG-1968-GL zero dead space drain valve. Approximate overall length of adapter is 1.75”.  NOTE: Requires a CG-1968 beaded pipe coupling.

Polished glass stirring shafts, 10mm OD. Recommended for use with only our 8050,8066,13443 and 13445 bearings. Join 8083,8085,8086,8087,8096 blades to button type shafts. Join 8088, 8089, 8090 & 8091 agitators to bead type shafts. Plain shafts will accept 8094 & 8095 agitators secured with a…

Stirring shaft with steel core. Use with PTFE stirrer guides and for applications which do not require a guide. Unbreakable, scratch resistant, and usable up to 280C.

Stirrer blade made of 1/8" thick solid PTFE for use with both Chem-Stir™ and button style stirring shafts having a 10mm OD.

A 19mm precision ground and polished stirrer shaft to fit CG-2086 19mm PTFE bearings. Side button for attachment of CG-2089 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF GLASS BEARING. FOR GROUND SHAFTS USED WITH GLASS BEARINGS SEE CG-2085. ALSO NOTE:…

Shaft is precision ground and polished to fit our CG-2076 and CG-2077 10mm PTFE bearings. Designed to be used with cylindrical type reactors. The straight glass blades are spaced 90° apart and angled 15°.  PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR COUNTER-CLOCKWISE ROTATION.

Designed to be used with 8068, 8070, 8071, 8074 or 8078 stirring shafts. Handy for positioning shaft in bearing, and preventing shaft from dropping into flask. Supplied with PTFE gasket to prevent scratching top of bearing and acts as dust cover. Available in either Glass-filled PTFE or 316…

Similar to CG-2070 but with a tooled lubricant cup at the top of the bearing to hold an increased amount of lubricant. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.

A 10mm precision ground stirrer shaft to fit CG-2070 through CG-2072 10mm bearings. Side button for attachment of CG-2080 or CG-2081 PTFE stirrer blades. PLEASE NOTE: THESE SHAFTS ARE NOT TO BE USED WITH ANY TYPE OF PTFE BEARING.  FOR POLISHED SHAFTS USED WITH PTFE BEARINGS SEE CG-2079.

A rugged, compact, inexpensive stirrer. The upper member turns with stirring shaft, bottom member remains stationary. Upper member supplied with vinyl connector. Use with ACE 8134 stirring shafts. Assembly may also be used to make your own rotary evaporator.

Support Stand was designed to accommodate vessels up to 10" diameter, to sit close to the support rod. Support rod is ideal for mounting stirring motors. Each of the four corners rests on a rubber cushion. The powder coated steel base measures 7.875” (200mm) W x 12.5" (316mm) deep…

Button type, solid glass stirring shafts, 5 & 6mm OD. Precision ground shafts, codes -04 & -06, should be used in matching glass Trubore 9524 and 9527 bearings. Polished shaft, code -40, should be used only in our 8066-120, 6mm PTFE inner bearing. All accept our 9542 blades. Join to stirrer motor…

Heavy duty 19mm stirrer bearing for use in stirring large volumes under high torque. Bearing has a tooled lubricant cup.PLEASE NOTE: NOT FOR USE WITH CG-2087 or CG-2088 PRECISION GROUND AND POLISHED STIRRER SHAFTS. STIRRER BEARINGS, 19MM, HEAVY DUTY, JACKETED, Similar to CG-2082 but with a water…

Precision bore bearing for use in moderate vacuum with a CG-2074 or CG-2075 ground 10mm stirrer shaft. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.

Nylon chuck for use with ACE stirring shafts or other shafts of the same dimensions. Chuck has flexible insert which allows for misalignment of shaft without danger of breakage.

Blade is shaped to resemble the contour of a round bottom flask. Blades are available solid or perforated. Made of 3/16" PTFE to fit 19mm OD stirrer shafts. Minimum joint size listed is the size required to allow passage of the blade.

Heavy duty PTFE anchor made of 0.500” thick PTFE. Blade is shaped to mirror the contour of Chemglass cylindrical reactors. Designed for use with CG-2078 Chem-Stir® 10mm stirrer shaft. The blade is secured to the stirrer via a PTFE pin.  PLEASE NOTE: CG-2081-A-02 IS NOT…

Eliminates Flask Breakage: PTFE is the only contact in the lower radius of the flask, therefore breakage due to dropping the stirrer shaft has been eliminated. Eliminates the Frustration of Assembly: Unique design permits the proper amount of tension to be applied to the blade,…

These heavy-duty PTFE agitators impart maximum energy and are offset at the bottom to accomodate slurries. 10mm agitators fit drilled type or knob type 8068, 8071 & 8075 shafts. 19mm agitators fit drilled type or knob type 8076, 8078 & 8079 shafts. 28mm agitators fit 8080 drilled shafts.

Precision ground, hollow, 5mm glass stirring shaft. Button type shaft accepts 9542 blades and can be used in matching 9524 and 9527 bearings. Holes are provided in the side of the shaft for material introduction and at the bottom for emission into the flask contents. Join to stirrer motor using…

PTFE stirrer bearing featuring a non-shedding, fully enclosed, anti-whip, chemically resistant design. Models available for 6, 8 and 10mm glass, metal or PTFE stir shafts. Can be used in slight pressure or vacuum applications. Maximum recommended speed for continuous operation is 500 rpm. Unlike…

Shafts are 316 stainless steel. All 3/8" (9.5 mm) dia shafts are machined on one end to accept a 5/16" (8 mm) bore diameter propeller.

PTFE stir blades for button type stir shafts. 10mm OD shafts can be found in our product series 8068, 8070, 8074 and 8075. 19mm OD shafts can be found in our 8076 and 8077 series.

Precision ground glass stirring shafts,10mm OD, crescent type. Useful for stirring viscous materials at low rpm. Available for round bottom flasks of 1, 3 and 5 liters. Code -19, 3 liter size will fit a 2 liter flask, but closely. Flask opening must be 29/42 or larger. Use with Trubore bearings…

Precision ground and polished, these borosilicate glass stirrer shafts have a 10mm O.D. For use with LG-9475T bearing with PTFE bearing surface, or other bearings with a PTFE interface with the same bore. Features a side button at bottom for attachment of any of the stirrer/stirring blades (LG-9505…

The unique design of our Tru-Stir™ stirrer shaft coupling eliminates the need to use rubber hose or universal adapters to attach your stirrer shafts to overhead stir motors. Coupling incorporates a unique helical stainless steel spring permitting up to 1/4” of offset misalignment and…

Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8076 (19mm od) or 8080 (28mm od) polished glass stir shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…

Shaft is precision ground and polished to fit our CG-2086 19mm PTFE bearings. Designed to be used with cylindrical type reactors. The curved glass blades are spaced 120° apart and angled upward. PLEASE NOTE: STIRRER SHAFTS ARE DESIGNED FOR COUNTER-CLOCKWISE ROTATION. ALSO NOTE: 19MM…

Thomas No. 1198F83: Stirring shaft with floating blades: The two blades that open as the speed rises generate an axial flow in the container, from the top towards the bottom. Particularly recommended for stirring in narrow-neck containers, e.g. flasks. Thomas No. 1198F84: Stirring shaft with…

Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8074 stainless steel or 8075 polished 10mm od glass shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…

PTFE banana shaped stir blades for 10mm OD button type stir shafts. 3mm thick blades have a number of perforations and are designed to closely fit various sizes of round bottom flasks. 10mm OD stir shafts can be found in our 8068, 8070, 8074 and 8075 series.

Uniquely designed and lubricant free, these precision stirrer/stirring bearings are self-aligning. The saddle O-ring provides constant force and a positive seal on the stirring rod that allows vacuum operation to as low as 1mm. Ground finish rods from other manufacturers are not recommended for use…