Digital magnetic stirrer with heating; the MSH-300i Intelli-stirrer is designed for laboratories with higher requirements. It offers digital setting and control of temperature and rotation speed. A powerful magnet allows mixing solutions with glycerine viscosity level. Maximum volume of stirred…

All propellers mixers are made of 316 stainless steel. They have a 5/16-24 internal thread for easy assembly with all of our stainless steel shafts. All stainless steel mixer shafts are made of 316 stainless steel. These quality mixer parts have a 5/16-24 external thread for easy assembly with all…

Stirrer Blades PTFE construction Fit all standard shafts Will not scratch glassware Hole diameter: 6.5 mm Model 8596G58 to G70 shafts are for use with 8596G18 to G50 blades.

Uniquely designed and lubricant free, these precision stirrer/stirring bearings are self-aligning. The saddle O-ring provides constant force and a positive seal on the stirring rod that allows vacuum operation to as low as 1mm. Ground finish rods from other manufacturers are not recommended for use…

The RT series of multi-position digital magnetic hotplate stirrers are ideal for synchronous heating and stirring applications. The wear-free magnetic coil technology provides consistent and noiseless stirring on all positions. The RT series of magnetic stirrers are available with 5, 10 and 15…

Accessory for OS20-Pro LCD, OS40-Pro LCD, OS20-S LED and OS40-S LED Digital Overhead Stirrers. Blades open with increasing speed for stirring in a round vessel with a narrow neck, used at medium and high speeds Polytetrafluoroethylene (PTFE) coating

Precision ground, hollow, 5mm glass stirring shaft. Button type shaft accepts 9542 blades and can be used in matching 9524 and 9527 bearings. Holes are provided in the side of the shaft for material introduction and at the bottom for emission into the flask contents. Join to stirrer motor using…

The Velp DLH is an intuitive overhead stirrer ensuring safety with overload, over-current and overheating protection. DLH guides the user through a bright and easy to read display. All the main parameters, including the set speed, actual speed, torque and timer are visible at a glance. Max…

With buffered load control and DC filtration. Ratings: AC three-prong output socket, standard NEMA type, 1200 watts. 0 -120 volts, variable, 60 Hz. maximum 10 amps. DC four-prong output socket, cinch type. 360 watts, 0 -150 volts, variable, filtered approximately 1/2 hp.max. 3 amps. A solid state…

Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique 3 piece design of Trubore inner bearing, compression seal nylon bushing and glass standard taper adapter allows for moderate misalignment of stir motor and the bearing cannot sieze the shaft. For use with 8077 & 8078 19mm od…

Safe Operations Extremely resistant sealed case IP 54 Protection class is a guarantee of durability also when working in aggressive environment Full protection in case of overload, overtemperature and over current™ Lock key to prevent unintentional modification of the…

Similar to CG-2070 but with a tooled lubricant cup at the top of the bearing to hold an increased amount of lubricant. NOTE: Not for use with CG-2078 or CG-2079 polished stirrer shafts.

Support Stand was designed to accommodate vessels up to 10" diameter, to sit close to the support rod. Support rod is ideal for mounting stirring motors. Each of the four corners rests on a rubber cushion. The powder coated steel base measures 7.875” (200mm) W x 12.5" (316mm) deep…

Universal Stirrer Shaft Coupling incorporates a universal joint to compensate for misalignment of drive motor and glass stirrer shaft. Nylon bushing compresses around shaft using an allen screw. Steel stud attaches directly to the chuck of a stirrer motor. Supplied complete with an allen wrench. …

Economical Compact design Stirring range: 100-1600 rpm Rugged construction The unit’s 5” x 5” top size saves valuable bench space. Alternating current motor and strong magnet provide longer life and vigorous stirring. Top is constructed of plastic. Stirrer has a one-year…

Bell-ennium Magnetic Stirrers are designed for both cell cultures in spinner flasks as well as for general laboratory procedures requiring the use of magnetic stirring equipment.  Bell-ennium stirrers offer the laboratory researcher a wide range of capabilities and the latest innovations in…

Explosion proof (XP) motor features a 5:1 right angle gearbox to reduce the overall height above support frame to 10.5”. Motor is supplied with a 30ft 18/3 SJEOO cord with twist lock connector. XP motor must be used in conjunction with our digital motor controller, and mounts to all our…

Eliminates Flask Breakage: PTFE is the only contact in the lower radius of the flask, therefore breakage due to dropping the stirrer shaft has been eliminated. Eliminates the Frustration of Assembly: Unique design permits the proper amount of tension to be applied to the blade,…

This incorporates a universal stirrer shaft coupling (CG-2046) to compensate for misalignment of drive motor and glass stirrer shaft. Nylon bushing compresses around shaft using an allen screw. Stainless steel stud and upper coupling attach directly to the motor shaft. For use with 30L…

Bell-ennium Magnetic Stirrers are designed for both cell cultures in spinner flasks as well as for general laboratory procedures requiring the use of magnetic stirring equipment. Bell-ennium stirrers offer the laboratory researcher a wide range of capabilities and the latest innovations in stirring…

Material: 316l stainless steel with ra32 finish or better Size: 8l

 The MAZ® is an integrated mixer and a deaerator system designed to perform both mixing and deaeration while simultaneously rotating and revolving the containers. This unique motion eliminates the need for mixing rods, blades and an evacuation device, thus reducing processing times. …

Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique design is forgiving of slight misalignment of stir motor and shaft. Recommended for use with our 9534 6mm precision ground stir shaft.

The IKA Plate (RCT digital) has a round top made of aluminum alloy. It stirs volumes of up to 20l (H2o) and runs at speeds ranging from 50-1500rpm. Some of the features are: IKA emphasizes ease-of-use by design simplicity: reduced forms and operating elements meet the modernity of smartphones:…

Caframo’s BDC2002 offers ultimate versatility and maximizes productivity. With the push of a button, the unique Stirlight™ lights up so that solutions can be seen clearly. Included in each purchase: Overhead stirrer motor, chuck, chuck key, support rod, external power supply, grounded…

The stirrers are designed for optimal suspension cell culture and the use of microcarriers. The system comprises of a stirrer platform and a number of glass culture vessels. MCS-102L accommodates two 1 litre culture vessels Speed range from 0 to 80rpm Softstart/stop for slow…

Magnetic stirrer with heating and ceramic heating plate which offers excellent chemical resistance. Powerful motor for stirring quantities of up to 5 l (H2O) Fixed safety circuit of 550 °C Hot Top indicator >> hot surface warning to prevent burns! Exact temperature setting via…

Thomas No. 1177M31 Sturdy stand in a smaller bench footprint, for Caframo compact stirrer models BDC2002 and BDC2010. The unique offset design accommodates Caframo clamp so stirrer locates impeller in centre of vessel. The cast zinc-aluminum alloy base is coated for protection from corrosion and…

Agitators are made entirely of PTFE and glass filled PTFE and are for use with 10mm OD stirrer shaft CG-2075-B. Available in 45°, 60° and 90° impeller angles. The 45° and 60° impellers are set up to stir downwards in a clockwise direction and upwards when rotated…

This strong, non-scratch and inert FDA grade, USP Class VI Teflon® PTFE blade fits all standard button-tip stirring shafts. "Long-groove" keyhole provides easy insertion into flask neck Rotates into proper position for stirring action

Support Stands are made entirely of 303 stainless steel. They have a durable base that can accommodate vessels up to 18" (457 mm) in diameter within the “U”. The base area is 17.75" (451 mm) across × 10.5" (267 mm) deep overall. The stainless steel support rod is…

The space-saving high performers from IKA MICROSTAR and MINISTAR series have been complemented by additional models. The new and easy-to-use stirrers convince with perfect basic functionalities, as well as with a compact design. Combining high performance with particular excellence, they require…