Septa

Compare Tool

Select up to 3 products

1 - 32 of 44
Sort
View
Show
  • 11mm Crimp Seals

    National Scientific

    Aluminum seals with pre-inserted septa are compatible with standard opening crimp top vials, wide opening Target LOVial™ crimp top vials and Target Snap-it™ crimp/snap vials.

  • Aluminum E-Z Seals

    DWK Life Sciences (Wheaton)

    For use with 12 x 32 mm crimp top vials Large target diameter Available in 4 colors Choice of liner

  • Thermogreen® LB-2 Septa, solid discs

    MilliporeSigma

    An improved version over the original Thermogreen LB-1 septa. Extremely low bleed over a wide range of inlet temperatures (100 °C to 350 °C) Already conditioned, ready to use Easier needle penetration and high puncture tolerance (ideal for autosamplers) Rubber formulation…

  • 3 Layer Septa

    Hamilton

    Three Layer Septa is made of preconditioned silicone rubber and is 3.81 mm (0.150 in.) thick. The average life of these septa is up to 100 injections with a 26s gauge needle. The maximum operating temperature is 200° C. Preconditioned silicone rubber septa, 3.81 mm (0.15“) thick …

  • Septa, Long Life GC Autosampler

    Hamilton

    Long injection life, pre-pierced for minimal coring. Maximum temperature 400°C. Long injection life septum typically achieves 400 injections without failure, when used with a rounded-tip (Agilent-style) needle and autosampler or needle guide. Ideal for standard manual-injection GC and GC/MS. 3 mm…

  • Septa, 0.005" PTFE/0.120" Sil

    DWK Life Sciences (Kimble)

    Resists coring and is autoclavable. Recommended for use in all auto samplers using screw thread vials. Great for sample storage. 73818A-24 ( 1213T38) is white PTFE/Tan Silicone and is recommended for use with the 40 mL EPA vial.

  • Septa PTFE Rubber 18-400 Cs144

    DWK Life Sciences (Kimble)

    Low cost, good resealability Polytetrafluoroethylene provides barrier for product contact Red rubber

  • Precision Seal® rubber septa cap white, for 5-6 mm O.D. tubes and ampules

    MilliporeSigma

    Synonym: rubber caps, rubber stopper, rubber stoppers Usage: for 5-6 mm O.D. tubes and ampules Color:   white General description Engineered for a "push on" fit in NMR tubes and ampules. The unique design provides a penetration point for cannulation and a dual…

  • Merlin Microseal

    Agilent Technologies

    Low bleed, longer life alternative to standard septa for split/splitless injection Has a lifetime of more than 2000 injections, depending on samples and operating conditions Reduced instrument downtime for septa changes and injection port liner changes due to septa particulates Two…

  • Headspace Septa and Stoppers

    Thermo Scientific Sun SRi

    Requires the use of 20mm aluminum seals

  • HT Predrilled Septa

    SGE

    Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.

  • Renewable Gas Purification System

    Agilent Technologies

    The Renewable Gas Purification System from Agilent not only traps large quantities of contaminants and lasts a long time, but it is also recyclable. With average use, you’ll only have to purchase a replacement cartridge once per year or after approximately 20 cylinders’ worth of…

  • Septa for 20mm Crimp Seals

    MicroLiter

    MicroLiter offers products for both LC and GC applications.

  • Premium HT quality GC injection port septa

    MACHEREY-NAGEL

    GC injection port septa High quality CenterGuide™ for centered needle guidance for a perfect fit Highest septum quality for minimal bleeding, even at high temperatures up to 400 °C (Shimadzu plug septa up to 300 °C) Precision trough for a perfect fit Special coating…

  • Septa, Low Bleed High Temperature

    Hamilton

    BTO is Bleed and Temperature Optimized for today's most demanding GC and GC/MS applications. Septa BTO is formulated to extend low-bleed and outstanding mechanical properties or premium GC septa to the highest-temperature applications. 3 mm thick. CenterGuide™ design requires less force for…

  • White FEP/Silicone Septa

    DWK Life Sciences (Kimble)

    Designed for use with headspace autosamplers  for sealing sample vials used in operating temperature ranges of -60 to 200°C.  For aluminum seal finishes Clear FEP is 0.003" thick White silicone is 0.120" thick

  • 33 mm Septa, Interlock, Butyl Gray

    DWK Life Sciences (Wheaton)

    Septa closure with locking flange for open-top caps. Flat stopper; thin flange Cap size: 33 mm Gray Chlorobutyl/50 septa

  • BTO Septa

    Chromatography Research Supplies

    Maximum setpoint: 400°C Low bleed Long injection life 3 mm thick CenterGuide™ chamber in one face guide the needle with each injection.

  • Headspace Pressure Release Seals

    DWK Life Sciences (Wheaton)

    20 mm crimp closure with liner for headspace vials Score lines allow for internal pressure release Choice of three liner options

  • Septa for screw caps, N 9

    MACHEREY-NAGEL

    Replacement septa for 9 mm screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C,…

  • Septa for screw caps, N 8

    MACHEREY-NAGEL

    Replacement septa for 8-425 screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C,…

  • Septa for PE Caps, N 20

    MACHEREY-NAGEL

    Single septa for all 20 mm PE push on caps (70266 + 70267) from MACHEREY-NAGEL Natural rubber / PTFE: temperature resistant: –40 °C / +120 °C, low analytical purity, high coring, fairly hard to penetrate, very good resealability Butyl / PTFE: temperature resistant: –40…

  • Standard quality GC injection port septa

    MACHEREY-NAGEL

    GC injection port septa Standard quality Septum grade: Standard septa (ST) Material: beige silicone Thickness: 4 mm Hardness: 60° shore A Septum grade: High temperature septa (HT) Material: red non-bleeding silicone Thickness: 3 mm Hardness: 60° shore A …

  • Sera-Separa®

    Evergreen Scientific

    For use in removing fibrin and macro particles from serum to prevent line clogging. Users insert the 16 mm flange into the evacuated blood tube and push downward. Graduated barrel tells exactly how much liquid has been filtered. Wide-body style prevents sample probes from hitting side walls.

  • Replacement Septa for Mininert® Valves

    MilliporeSigma

    Material: Red Silicone Septa L x O.D.: 0.308 in. x 0.125 in. Legal Information Mininert is a registered trademark of Valco Instruments Co. Inc.

  • Septa for crimp caps, N 20

    MACHEREY-NAGEL

    Single septa for all 20 mm crimp caps from MACHEREY-NAGEL Butyl / PTFE: temperature resistant: –40 °C / +120 °C, medium analytical purity, medium coring, medium hard to penetrate, resealability medium Silicone / PTFE: temperature resistant: –60 °C / +200 °C high…

  • Septa for screw caps, N 13

    MACHEREY-NAGEL

    Single septa for 13-425 screw caps from MACHEREY-NAGEL PTFE virginal: temperature resistant: –200 °C / +260 °C, very high analytical purity, very hard (but very thin material), no resealability Red Rubber / TEF (FEP): temperature resistant: –40 °C / +110 °C, medium…

  • Butyl Gray Headspace Vial Septa

    National Scientific

    For 20 mm vials Temperature range: 40° to 120°C Does not provide PTFE barrier Not suitable for alkalines, benezene, chlorinated solvents or cyclohexane

  • Septa PTFE Silicone 24-400 Cs144

    DWK Life Sciences (Kimble)

    Resists coring and is autoclavable. Recommended for use in all auto samplers using screw thread vials. Great for sample storage.

  • MN Grade Silicone Septa

    SGE

    Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.

  • HT Grade BTO Silicone Septa

    SGE

    Your chromatography analysis does not end with the selection of the GC column. The combination of components selected for your instrument also make an important contribution to successful separations. Choose SGE technology to improve your chromatography.

  • Septa, tan PTFE/silicone

    MilliporeSigma

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.