For analysis of polar substances The organic sorbent cellulose is particularly suitable for the separation of hydrophilic substances by partition chromatography. EMD Millipore cellulose plates include classical TLC grade or HPTLC plates for demanding high-performance separations: TLC…

Analtech’s flexible backed TLC plates offer the same exacting specifications as with the classic glass backed plates assuring batch-to-batch uniformity. Quality is controlled at each step in the manufacturing process — from incoming raw materials to outgoing packaging. Lighter…

Provides a uniform spray mist of visualization reagents for both thin layer and paper chromatography Borosilicate glass Handles all standard TLC spray reagents and most corrosive liquids Creates consistent spray patterns that are free of damaging droplets The connection between the sprayer…

Constructed of sturdy molded glass bricks Withstands regular use for many years The tank’s clear sides allow for visual inspection of TLC plates up to 20 x 20 cm size. The top of the tank is ground flat to match the lids and the edges are beveled to remove any sharp edges. The bottoms are…

Provides uniformly fine mist or spray, required for paper chromatographic determination Conveniently located vent permits instantaneous control of spray Borosilicate glass tube has permanently attached, molded phenolic screw cap (size No. 24) with polyvinyl liner which fits commercial narrow…

Clear glass sides allow unobstructed visual inspection of contents Tank is ground flat to match ground glass lid. Beveled inside and outside to remove any sharp edges. Holds two 20 x 20 cm plates or four 10 x 20 cm plates. Latching device holds the matching ground glass surfaces of the lid…

Ready-to-use plastic sheets, 50 x 200 mm or 200 x 200 mm, with absorbent coating, which is abrasion-resistant and highly uniform; are easily cut to desired size and allow sample fraction to be cut rather than scraped The silica gel and aluminum oxide sheets have coating approximately 200 microns…

Beveled inside and outside to remove any sharp edges Raised ridge midway on the inside ends and bottom for developing two 20 x 20 cm plates or the equivalent Inside dimensions: 27 x 7 x 26 cm Supplied with flat glass lid, 30 x 10 x 3 cm Molded glass block of clear glass with…

The single most useful chamber for the TLC laboratory is a sturdy, molded-glass block of clear glass with flat surface walls, ground lip of uniform flatness, beveled inside and outside to remove any sharp edges. There is a raised ridge midway on the inside ends and bottom of the jar. Inside…

Nest cell culture plates have round edges for better handling. Low profile, low-evaporation lid design assure uniform growth. Small feet on the bottom corners of each plate eliminate scraping of the microscope lens. Sterilized by E-beam High clarity, 100% virgin polystyrene Vacuum…

Requires less solvent to maintain equilibrium Gives excellent retention of solvent saturated chamber Holds two 10 x 10 cm plates The smaller cubic inch chamber allows for a faster and more uniform solvent-saturated atmosphere. Single molded tank has a flat ground top, beveled for…

Flat ground top is beveled on the inner and outer rim Ground flat bottom for stability Holds two 10 x 10 cm plates or four 5 x 10 cm plates Thin-Line units allow for faster and more uniform solvent saturated atmosphere and therefore require less solvent. Inside dimensions: 12 x 6.4…

High optical-quality glass bottom, black microplates are ideal for performing high-content cell-based assays using imaging systems. The glass bottom provides a flat and optically clear surface that reduces autofocus time, increases throughput and is ideal for cell growth. High optical quality…

Aluminium oxide, specific surface (BET) ~ 200 m 2 /g, mean pore size 60 Å; inert organic binder indicator manganese-activated zinc silicate available as glass plates, POLYGRAM® polyester sheets and ALUGRAM® aluminium sheets Recommended application: terpenes, alkaloids,…

Silica Gel G & GF UNIPLATES are the most widely used silica gel TLC plates. No organic substances are added to these products, thus making them compatible with sulfuric acid charring visualization. These plates are commonly scraped from the glass backing to isolate separated components for…

Aluminiumoxide plates are used to analyze basic and neutral compounds at different pH levels. Depending on the pH range in question, professionals can choose between two kinds of aluminum oxide plates. Under aqueous conditions, basic aluminum oxide plates are best for separating basic compounds,…

CAS Number: 2049-80-1 Molar Mass: 200.23 g/mol Boiling Point: 105 - 107°C (22.7 hPa) Flash Point: 92°C Density: 1.016 g/cm3 (20°C)

Store TLC plates without damaging delicate media Holds up to 10, 20 x 20 cm plates or equivalent number of narrower plates Racked plates may be air or oven dried Can be used with plates in either vertical or horizontal position Racks are also used for storage of dried layers…

These reversed phase TLC plates have been manufactured to be greater than 50% and less than 100% silanized. Because of this they are hydrophobic, but wettable. Features: 14% carbon content Acid stable (UV254) fluorescent indicator Glass backing 250um coating thickness 25…

For Thin Layer Chromatography

Classic silica TLC plates are based on a combination of proven EMD Millipore silica gel 60 and the addition of a unique polymeric binder resulting in a very adherent and hard surface that will not crack or blister and even allow writing with a pensil on the surface without risk to damage the layer.

Aluminiumoxide plates are used to analyze basic and neutral compounds at different pH levels. Depending on the pH range in question, professionals can choose between two kinds of aluminum oxide plates. Under aqueous conditions, basic aluminum oxide plates are best for separating basic compounds,…

RP modified plates serve two purposes: act as a pilot method for HPLC and allow to choose various solvent system for special separations. RP-modified silica layers from EMD Milliporeare well suited for many separation challenges that unmodified silica cannot overcome. These layers use aqueous…

material       polyester support, silica gel matrix feature       binder Polymeric, fluorescent indicator L × W       20 cm × 20 cm layer thickness       200 μm particle size…

EMD Millipore classical silica TLC plates are based on a combination of proven EMD Millipore silica gel 60 and the addition of a unique polymeric binder resulting in a very adherent and hard surface that will not crack or blister and even allow writing with a pensil on the surface without risk to…

Silica Gel G & GF UNIPLATES are the most widely used silica gel TLC plates. No organic substances are added to these products, thus making them compatible with sulfuric acid charring visualization.These plates are commonly scraped from the glass backing to isolate separated components for other…

Corning now offers a line of generic bar coded plates to better meet the demands of your screening needs. Labels applied to all 4 sides of the microplate to ensure usability regardless of scanner location Each microplate is specially treated to reduce the impact of static…

High Performance UNIPLATES provide high resolution separations in less than five minutes with migration distances as little as 5 to 7 cm. These plates are prepared with high efficiency silica gel having a 10 micron average particle diameter and narrow particle size distribution. The adosrbent…

When using thin layer or paper chromatography (TLC), these borosilicate glass atomizers are used for spraying chromogenic reagents. Complete unit consists of spray head, flask, and LG-1004 clamp. The air inlet tube has an opening to release pressure and stop spraying. All joints are Standard Taper 24/40.

For thin layer and preparative layer chromatography Ready-to-use Layer thickness 0.25 mm Allow safe spotting without layer damage Plates have a uniform, abrasion-resistant coating and a patented, inert, hard-layer binder that is chip and abrasion-resistant. F254 is a…

Classic silica TLC plates are based on a combination of proven EMD Millipore silica gel 60 and the addition of a unique polymeric binder resulting in a very adherent and hard surface that will not crack or blister and even allow writing with a pensil on the surface without risk to damage the layer.

EMD Millipore classical silica TLC plates are based on a combination of proven EMD Millipore silica gel 60 and the addition of a unique polymeric binder resulting in a very adherent and hard surface that will not crack or blister and even allow writing with a pensil on the surface without risk to…