Our valves have low internal volumes and are rated to 15,000 psi (103,421 kPa). They feature a two-piece stem assembly in which the rotating upper shank is coupled through a ball joint to a static lower stem. Only finger-tight torque is required to make the seal.

Protect contents and prevent carryover with pre-slit cap mats Chemically resistant, silicone mats are excellent for compound storage to -80°C Pre-slit mats pierceable by autosampler needle, pipette tip, or probe Universal mat for sealing 0.45, 1.3, and 2.0 mL plates

Precut, micropolished tubing and preseated fittings for quick, easy maintenance of your Agilent HPLC systems Meet or exceed manufacturer's performance.

Buffer salts and metals from the HPLC system become imbedded on the surface of the piston seal and gradually wear the surface of the piston rod. Worn regions on the rod will quickly destroy the pump seals. In turn, the seal material gets trapped on the frit at the head of the column, which leads to…

Storage for ten HPLC columns (minimum 100 mm in length), compartments for accessories, and a book holder* Small footprint—easily fits next to HPLC instruments *Please note: Accessories and supplies in photograph are not included.

?Polypropylene plates with round-bottom wells reduce liquid retention; conical bottom provides optimal recovery of reagents. Nunc shared wall technology allows increased well volume for optimum storage capacity and improved mixing. Round well shape is ideal for applications that require…

In-line design installs easily with standard fittings Cost-effective protection for UHPLC systems Reliable way to extend column lifetime Leak-tight to 15,000 psi (1,034 bar) Replaceable 0.5 µm stainless steel frit in stainless steel body

Restek’s high-pressure in-line filter is a stand-alone version of the Trident column protection system, specifically designed for ease of use, low dead-volume, and flexibility. The filter has a replaceable, PEEK encapsulated 316 stainless steel frit with a surface area of 12 mm 2 . The…

Standard lamps have nominal 1,000-hour life.

The sparge filter is an inexpensive way to prepare and maintain mobile phases free of dissolved gas. Filters are made from 316 stainless steel and PEEK, and they are compatible with most solvents. Connects to standard 1/8" OD (3.2 mm) PTFE tubing.

Hand-tight fitting style achieves effortless HPLC seals—no tools needed for a 8,700+ psi seal Both hand-tight and hex-head styles wrench-tighten for reliable UHPLC use up to 20,000+ psi! Patented ferrule can be installed repeatedly without compromising high-pressure seal Hybrid…

Tubing elbows (90° and 180°) are ideal for routing 1/16" PEEK tubing through your system. Simply snap the tubing into the elbow. Prevent pinching of PEEK tubing, which can cause high pressure.

Universal PEEK connectors allow easy installation of all 1/16" tubing, including stainless steel, up to 5,000 psi.

Securely holds 1/16" or 1/8" tubing in beaker, flask, or bottle up to 4 mm thick.

These 1/4" compression end-fittings are compatible with 1/16" connecting tubing using Valco and Parker fittings. Fittings with distribution cone are intended for use on 3.0–4.6 mm ID HPLC columns Fittings with flat bottom are intended for use on 1.0–3.0 mm ID HPLC columns

Standard lamps have nominal 1,000-hour life.

An efficient cross-flow shearing mechanism and interchangeable cartridges produce vortex shear mixing over a wide range of flows. Stainless steel or PEEK. Reduced baseline noise Increased sensitivity Improved gradient accuracy for more reproducible results Increased reaction…

This HPLC PEEK Performance Kit is a useful complement to your HPLC system. Includes: Hub-Cap Adapter w/ Cap (1) Tubing Clips (3) Clean Cut Tubing Cutter (1) PEEK Finger Tight Fittings (5) PEEK Column Plugs (5) PEEK 90° Tubing Elbows (2) PEEK 180° Tubing Elbows…