Labconco Chemical Fume Hoods
-
SpillStopper Work Surface molded of corrosion-resistant solid epoxy. Dished & contoured to conform to interior liner of Protector Pass-Through Hoods. Pre-drilled 2.5" (6.4cm) dia plumbing holes.
-
Filtermate Portable Exhausters
LabconcoCompact, corrosion-resistant housing Inherently safe design An accessory for the Demonstration Hood, XPert Balance Enclosure, Protector® XVS Ventilation Station or Protector® Work Station, the FilterMate uses a HEPA filter, carbon-based filter or a combination of both filters…
-
Ideal for fume hood exhaust systems in moderate to highly corrosive conditions. Intelli-Sense Multi-Speed Blowers are weatherized, direct drive, non-explosion-proof blowers controlled by a two or three position switch. Each blower has a reliable electronically commutated motor (ECM), which…
-
Solid Epoxy Work Surfaces
LabconcoBlack chemical-resistant work surface is contoured to fit the dimensions of the enclosure and to contain spills. These surfaces can be used with Protector XVS Ventilation Stations, Protector Work Stations, Purifier Non-Ventilated PCR Enclosures and Tissue Culture Enclosures.
-
XPert Filtered Balance Systems provide user protection by keeping powders and particulates contained during weighing procedures. Patented features include an ergonomic air foil with Clean-Sweep openings to enhance airflow and a zone-perforated rear baffle that creates horizontal laminar airflow to…
-
Protector Airo Filtered Fume Hoods
LabconcoThe Protector® Airo™ Filtered Fume Hood has a compact design that avoids potential challenges of existing lab conditions while still providing space, utility and options of a traditional hood. It features all of the characteristics of Labconco Protector Hoods including the patented…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
SpillStopper Work Surfaces are compatible with Protector (Premier or XStream) Laboratory Hoods with Eco-Foil(TM) Air Foil. Molded from a special formulation of corrosion-resistant epoxy resins, these work surfaces are dished and contoured to conform to the interior liner of Protector Laboratory…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
The Protector XL Benchtop Laboratory Hoods offer superior design flexibility. Their panel liners are supplied in three depths to meet individual installation and application requirements. Protector XL Benchtop Laboratory Hoods are suitable for general chemistry applications. Features …
-
-
gGuard® Communication Software Automatically collects and records hood data, alerts and alarms on a customer-supplied personal computer Monitors, manages and provides data via email to a designated facility manager Provides access to the following: usage authorization, filter…
-
Protector Fume Hood Accessories
LabconcoScreen mounts behind the baffles for trapping tissue wipers & other papers. Each kit includes mounting hardware, powder-coated stainless steel screen & instructions. Contact Labconco for screens for hoods wider than 8'.
-
Applicable Products: Basic Laboratory Hoods For installation in a factory-prepared cutout on the upper portion of the Basic Hood's right side fixture panel. Guardian 500 Airflow Monitor senses and alerts the operator to low airflow conditions. Includes a face plate with circuit…
-
Monitor features an LCD that displays average face velocity. Audible/visual alarm alerts user to low or high face velocity. Kit is for installation in a factory-prepared cutout on the upper portion of the right side fixture panel. Kits are available for use with 115V, 60 Hz operation or 230V,…
-
Protector Pass-Through Laboratory Hoods offer sashes on two sides allowing operation on either side of the fume hood. An audible alarm sounds to prevent simultaneous opening of both sashes. With unobstructed visibility from either side, this hood is ideal for conducting chemistry demonstrations. …
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Protector Pass-Through Laboratory Hoods offer sashes on two sides allowing operation on either side of the fume hood. An audible alarm sounds to prevent simultaneous opening of both sashes. With unobstructed visibility from either side, this hood is ideal for conducting chemistry demonstrations. …
-
Protector Work Station Accessories
LabconcoFilters for Labconco protector work stations Impregnated charcoal filter packs remove dangerous vapors from the work area 5165N47 1 3/8” filters slip behind stainless steel grill to remove formaldehyde vapors quickly and completely
-
Protector standard storage cabinet features 18 gauge steel exterior sidewalls that are epoxy-coated for chemical resistance. Cabinets feature two non-locking manual doors. Four individual leveling feet allow users to make adjustments to level the cabinet based on the condition of their floors.…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
SpillStopper Work Surfaces are compatible with Protector (Premier or XStream) Laboratory Hoods with Eco-Foil(TM) Air Foil. Molded from a special formulation of corrosion-resistant epoxy resins, these work surfaces are dished and contoured to conform to the interior liner of Protector Laboratory…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
Protector Work Stations
LabconcoFace velocities from 60 to 100 fpm Built-in dynamically-balanced motorized impeller Speed controlled to achieve desired inflow velocity Protector Work Stations are specifically designed for the needs of pathologists and histotechnologists. Like a traditional fume hood, these enclosures have a…
-
Fiberglass 30 Laboratory Hoods
LabconcoCompact, benchtop Fiberglass 30 Laboratory Hoods are designed for research, educational and clinical applications requiring small working space and efficient fume removal. The fiberglass liner is corrosion-resistant, durable, fire-resistant and light reflective. The smooth one-piece molded…