SpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled…

4' Frame Measures: 36" x 38" 6' Frame Measures: 36" x 62" 8' Frame Measures: 36" x 86" Chamfered Ends Rods are corrosion-resistant

Compact, corrosion-resistant housing Inherently safe design An accessory for the Demonstration Hood, XPert Balance Enclosure, Protector® XVS Ventilation Station or Protector® Work Station, the FilterMate uses a HEPA filter, carbon-based filter or a combination of both filters…

Clean Aire II Fume Hoods are a Class 1 ductless hood workstation with activated Carbon Filtration for fumes, odors, non-hazardous chemical vapors. This is a self contained ductless hood unit, equipped with integral carbon filter, vapor proof light, vertical sash and controls, and completely molded…

The Universal Fume Hood is designed for light to medium duty fume removal, and offers such features as a sturdy dual wall construction, and a fully vertical sliding sash. It is completely molded of fire retardant fiberglass. Thomas Numbers 1167M01-M04: Units do not have a blower and require a…

XPert Filtered Balance Systems provide user protection by keeping powders and particulates contained during weighing procedures. Patented features include an ergonomic air foil with Clean-Sweep openings to enhance airflow and a zone-perforated rear baffle that creates horizontal laminar airflow to…

High Performance Chemical Fume Hoods   The expansive interior is enhanced by a 43" tall sight line with a 17" in high glass observation panel. Includes frameless vertical rising sash with a 24" clear sash opening. This hood has easy conversion from CAV to VAV use. Includes…

Canopy hoods are designed to collect and exhaust corrosive vapors, heat, steam, and odors when mounted over areas with water baths, hot plates, or portable equipment. Made of composite resin, the Canopy Fume Hood’s glass smooth surfaces provide superior chemical, corrosion and heat…

Traps solvent vapors Fume Adsorber is designed for histology cover slipping and staining areas and uses activated carbon media to adsorb annoying odors and noxious vapors such as xylene and toluene. Solvent vapors are trapped in the capillary-like channels of the carbon filter while clean air is…

The Purifier Axiom Class II, Type C1 is the first biological safety cabinet that can be used in a recirculating Type A-mode for standard microbiological work, or can be connected to an exhaust system to function in Type-B mode for handling hazardous chemical vapors or radionuclides. Because of the…

XPert Filtered Balance Stations are designed to protect the user during powder weighing operations. Ducting to an outside blower is required. Patented features include an ergonomic air foil with Clean-Sweep openings to enhance airflow and a zone-perforated rear baffle that creates horizontal…

If you have robust chemical applications requiring a fume hood but have low ceiling height and no means to duct to the outside, consider the Protector® Airo™ Filtered Fume Hood. Labconco has combined its patented* fully-featured, containment- enhancing Protector® Hood design with…

The newly redesigned, patented* Protector XStream Laboratory Hood was engineered to be the best containing fume hood possible. Testing shows the Protector XStream easily meets containment per SEFA-1 low velocity hood standards when subjected to the ASHRAE 110 test protocol with results of less than…

Protector XL Floor-Mounted (Walk-In) Laboratory Hoods have panel liners that may be constructed of a variety of corrosion-resistant materials and supplied in three depths to meet individual installation and application requirements. They are suitable for general chemistry applications and…

Protector Echo Filtered Fume Hoods with Neutrodine filtration are appropriate for procedures that require personnel protection in a lab that cannot accomodate duct work nor make-up air. Labconco has combined its patented fully-featured, containment-enhancing Protector® Hood design…

Epoxy coated steel, belt drive, exhaust blowers for canopy hoods based on duct runs under 25ft and no more than 4 elbows. These exhaust blowers are designed to maintain between 80 to 100FPM.

The Protector XStream I-S Laboratory Hood was engineered to be the best containing fume hood possible. Testing shows the Protector XStream I-S easily meets containment per SEFA-1 low velocity hood standards when subjected to the ASHRAE 110 test protocol with results of less than 0.05 ppm leak rate…

Type 304 stainless steel work surfaces have a 1" deep front spill trough and fit dimensions of Xpert Systems and Stations.

The Protector XL Benchtop Laboratory Hoods offer superior design flexibility. Their panel liners are supplied in three depths to meet individual installation and application requirements. Protector XL Benchtop Laboratory Hoods are suitable for general chemistry applications. Features …

The patented Protector ClassMate Laboratory Hood is designed to meet the needs of instructional laboratories. Clear back and sides and taller front viewing window provide enhanced visibility for conducting chemistry demonstrations or observing students using the hood. The clear back also does not…

Protector Pass-Through Laboratory Hoods offer sashes on two sides allowing operation on either side of the fume hood. An audible alarm sounds to prevent simultaneous opening of both sashes. With unobstructed visibility from either side, this hood is ideal for conducting chemistry demonstrations. …

Protector PVC Acid Digestion Laboratory Hood. 37.7" deep. Features heat-welded unplasticized PVC liner, built-in washdown system, integral work surface, drainage trough and 3-16" thick tempered safety glass vertical-rising sash with frame of powder-coated aluminum and PVC (glass is suitable for…

Protector Echo Filtered Fume Hoods with Neutrodine filtration are appropriate for procedures that require personnel protection in a lab that cannot accomodate duct work nor make-up air. Labconco has combined its patented fully-featured, containment-enhancing Protector® Hood design…

UniFlow LE Airestream fume hoods are a high-efficiency, full duty, low flow constant volume for energy savings & maximum user protection. The aerodynamic face opening with airfoil provides uniform air flow through the fume chamber. The Vector baffle system directs the air through the fume…

Filters for Labconco protector work stations Impregnated charcoal filter packs remove dangerous vapors from the work area 5165N47 1 3/8” filters slip behind stainless steel grill to remove formaldehyde vapors quickly and completely

Applicable Products: Fiberglass 30 Laboratory Hoods, Protector PVC Acid Digestion Laboratory Hoods, Protector PVC Perchloric Acid Laboratory Hoods, Protector Radioisotope Laboratory Hoods, Protector Perchloric Acid Laboratory Hoods, Protector XL Laboratory Hoods, Protector XLE Laboratory Hoods,…

Protector Echo Filtered Fume Hoods with Neutrodine filtration are appropriate for procedures that require personnel protection in a lab that cannot accomodate duct work nor make-up air. Labconco has combined its patented fully-featured, containment-enhancing Protector® Hood design…

Healthier, cleaner air in your laboratory Halo Smart is a ceiling mounted laboratory grade air filtration system working to purify the air from fugitive emissions present in the lab, while also providing real-time communication with the lab manager and users, of the air pollution levels and…