Chemical Fume Hoods

Compare Tool

Select up to 3 products

HomeAll Products

Hoods Chemical Fume Hoods

1 - 32 of 97
Sort
View
Show
  • Captair Smart Ductless Fume Hoods

    Erlab

    Simpler to use, Safer to operate Erlab’s Captair Smart ductless fume hoods are designed with advanced carbon filtration, Flex Technology and a simple, innovative way to keep you safe. With Erlab’s unique validation process, safety is guaranteed and chemical exposure is eliminated…

  • Protector® Airo™ Filtered Fume Hoods

    Labconco

    If you have robust chemical applications requiring a fume hood but have low ceiling height and no means to duct to the outside, consider the Protector® Airo™ Filtered Fume Hood. Labconco has combined its patented* fully-featured, containment- enhancing Protector® Hood design with…

  • Protector ClassMate Laboratory Fume Hoods

    Labconco

    The patented Protector ClassMate Laboratory Hood is designed to meet the needs of instructional laboratories. Clear back and sides and taller front viewing window provide enhanced visibility for conducting chemistry demonstrations or observing students using the hood. The clear back also does not…

  • Protector XL Benchtop Laboratory Hoods

    Labconco

    The Protector XL Benchtop Laboratory Hoods offer superior design flexibility. Their panel liners are supplied in three depths to meet individual installation and application requirements. Protector XL Benchtop Laboratory Hoods are suitable for general chemistry applications. Features …

  • Protector® Premier® Laboratory Hoods

    Labconco

    Protector® Premier® Laboratory Hoods incorporate a sleek interior with a molded one-piece fiberglass liner, the signature feature of Labconco’s leading line of fume hoods since 1961. The one-piece liner of specially-formulated, fiberglass-reinforced polyester offers corrosion and fire resistance…

  • Stainless Steel Wall Canopy Hoods

    Hemco

    Canopy hoods are designed to collect and exhaust corrosive vapors, heat, steam, and odors when mounted over areas with water baths, hot plates, or portable equipment. Made of type 304 Stainless Steel, the Canopy Fume Hood’s glass smooth surfaces provide superior chemical, corrosion and heat…

  • 5' Protector Pass-Through Laboratory Hoods

    Labconco

    Protector Pass-Through Laboratory Hoods offer sashes on two sides allowing operation on either side of the fume hood. An audible alarm sounds to prevent simultaneous opening of both sashes. With unobstructed visibility from either side, this hood is ideal for conducting chemistry demonstrations. …

  • Filtermate Portable Exhausters

    Labconco

    Compact, corrosion-resistant housing Inherently safe design An accessory for the Demonstration Hood, XPert Balance Enclosure, Protector® XVS Ventilation Station or Protector® Work Station, the FilterMate uses a HEPA filter, carbon-based filter or a combination of both filters…

  • Table Top Mount Lab-Frame Kits for Fume Hoods

    Lee Engineering

    Frame Measures: 36" x 38" x 9" Chamfered Ends Rods are corrosion-resistant

  • Protector XStream Laboratory Hood

    Labconco

    The newly redesigned, patented* Protector XStream Laboratory Hood was engineered to be the best containing fume hood possible. Testing shows the Protector XStream easily meets containment per SEFA-1 low velocity hood standards when subjected to the ASHRAE 110 test protocol with results of less than…

  • UniFlow LE AireStream Laboratory Fume Hoods

    Hemco

    UniFlow LE Airestream fume hoods are a high-efficiency, full duty, low flow constant volume for energy savings & maximum user protection. The aerodynamic face opening with airfoil provides uniform air flow through the fume chamber. The Vector baffle system directs the air through the fume…

  • Intelli-Sense™ Multi-Speed Fiberglass Blowers

    Labconco

    Ideal for fume hood exhaust systems in moderate to highly corrosive conditions. Intelli-Sense Multi-Speed Blowers are weatherized, direct drive, non-explosion-proof blowers controlled by a two or three position switch. Each blower has a reliable electronically commutated motor (ECM), which…

  • HEPA Exhaust Filter For Cabinet 6' Purifier Logic II Cabinets And 6' Puricare

    Labconco

    Carbon-based and HEPA filters used in a variety of Labconco enclosures require periodic replacement. Applicable products include: PuriCare Procedure Stations (pre-2008), Purifier Cell Logic Biosafety Cabinets and Purifier Logic Biosafety Cabinets with an enclosure nominal width of 6 feet.

  • Accessories & Replacement Parts for Protector Echo Filtered Fume Hoods

    Labconco

    gGuard® Communication Software Automatically collects and records hood data, alerts and alarms on a customer-supplied personal computer Monitors, manages and provides data via email to a designated facility manager Provides access to the following: usage authorization, filter…

  • Fume Adsorbers

    Labconco

    Traps solvent vapors Fume Adsorber is designed for histology cover slipping and staining areas and uses activated carbon media to adsorb annoying odors and noxious vapors such as xylene and toluene. Solvent vapors are trapped in the capillary-like channels of the carbon filter while clean air is…

  • Protector XStream I-S Laboratory Fume Hoods

    Labconco

    The Protector XStream I-S Laboratory Hood was engineered to be the best containing fume hood possible. Testing shows the Protector XStream I-S easily meets containment per SEFA-1 low velocity hood standards when subjected to the ASHRAE 110 test protocol with results of less than 0.05 ppm leak rate…

  • SpillStopper™ Work Surfaces, 6' Wide

    Labconco

    SpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled…

  • Purifier® 6' Axiom™ Class II, Type C1 BioSafety Cabinets with 8" Sash

    Labconco

    The Purifier Axiom Class II, Type C1 is the first biological safety cabinet that can be used in a recirculating Type A-mode for standard microbiological work, or can be connected to an exhaust system to function in Type-B mode for handling hazardous chemical vapors or radionuclides. Because of the…

  • Guardian 500 Airflow Monitors (for Basic Laboratory Hoods)

    Labconco

    Applicable Products: Basic Laboratory Hoods For installation in a factory-prepared cutout on the upper portion of the Basic Hood's right side fixture panel. Guardian 500 Airflow Monitor senses and alerts the operator to low airflow conditions. Includes a face plate with circuit…

  • Purifier® 4' Axiom™ Class II, Type C1 BioSafety Cabinets with 8" Sash

    Labconco

    The Purifier Axiom Class II, Type C1 is the first biological safety cabinet that can be used in a recirculating Type A-mode for standard microbiological work, or can be connected to an exhaust system to function in Type-B mode for handling hazardous chemical vapors or radionuclides. Because of the…

  • HEPA Filter Cell Bag Replacement

    Labconco

    Replacement Bag for Bag-in/Bag-out HEPA Filter to contain particulate matter during filter changing.

  • Fiberglass Wall Canopy Hoods

    Hemco

    Canopy hoods are designed to collect and exhaust corrosive vapors, heat, steam, and odors when mounted over areas with water baths, hot plates, or portable equipment. Made of composite resin, the Canopy Fume Hood’s glass smooth surfaces provide superior chemical, corrosion and heat…

  • Protector Work Stations

    Labconco

    Face velocities from 60 to 100 fpm Built-in dynamically-balanced motorized impeller Speed controlled to achieve desired inflow velocity Protector Work Stations are specifically designed for the needs of pathologists and histotechnologists. Like a traditional fume hood, these enclosures have a…

  • Guardian Digital Airflow Monitor Kits

    Labconco

    Monitor features an LCD that displays average face velocity. Audible/visual alarm alerts user to low or high face velocity. Kit is for installation in a factory-prepared cutout on the upper portion of the right side fixture panel. Kits are available for use with 115V, 60 Hz operation or 230V,…

  • Scienceware® Large Molded Fume Hood with Baffle

    Bel-Art - SP Scienceware

    This fume hood features a one-piece shell molded of polyethylene plastic with a flat internal baffle and a clear acrylic sash that slides on inside tracks. Internal baffle across the rear of the shell slopes forward, leaving space beneath for air flow to sweep the deck, and space above in…

  • Organic Filter Cell

    Labconco

    Organic Carbon Filter, Type AC. Contains 12 pounds of granular activated carbon media suitable for organic solvents including acetone, ethyl acetate, toluene and xylene. Carbon-based filters used in a variety of Labconco enclosures require periodic replacement.

  • SpillStopper™ Work Surfaces, 3' Wide

    Labconco

    SpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled…

  • SpillStopper™ Work Surfaces, 5' Wide

    Labconco

    SpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled…

  • Guardian 1000 Digital Monitor, 115V

    Labconco

  • Sciencware® Tapered Rear Exhaust Fume Hoods

    Bel-Art - SP Scienceware

    Ideal Vent for Tanks and Vats These polypropylene exhaust hoods are intended to rest on the rear edge of a tank and draw a stream of air across the top of the tank, away from the operator. An exhaust system is required. Formula for calculating required airflow for hood: 1.833 x 150 = 274.95…

  • SpillStopper Work Surfaces, for Protector XStream Hood

    Labconco

    SpillStopper Work Surfaces are compatible with Protector (Premier or XStream) Laboratory Hoods with Eco-Foil(TM) Air Foil. Molded from a special formulation of corrosion-resistant epoxy resins, these work surfaces are dished and contoured to conform to the interior liner of Protector Laboratory…

  • 8' Protector Echo Filtered Fume Hoods

    Labconco

    Protector Echo Filtered Fume Hoods with Neutrodine filtration are appropriate for procedures that require personnel protection in a lab that cannot accomodate duct work nor make-up air. Labconco has combined its patented fully-featured, containment-enhancing Protector® Hood design…

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.