Hoods
-
Exhaust Snorkel
INSTOCK LabsLab Exhaust Snorkels are suitable for the removal of heat or nuisance fumes. Exhaust Snorkels need to be tied into the general exhaust for the lab. Each lab snorkel is furnished with 5.5" mini hood that will accept the optional hoods noted. The two outermost joints can rotate and swivel…
-
HEPA Filters
AirClean® SystemsHEPA filters are designed to trap particulate and can be used in ductless fume hoods or laminar flow products. Ideal for use as a clean room HEPA filter. Required for laminar flow products. Filter Type: ACFHEPA Application: Containment of particulate only. Filter efficiency 99.997%…
-
Fume Hoods, fittings and accessories
INSTOCK LabsHigh Performance Chemical Fume Hoods The expansive interior is enhanced by a 43" tall sight line with a 17" in high glass observation panel. Includes frameless vertical rising sash with a 24" clear sash opening. This hood has easy conversion from CAV to VAV use. Includes…
-
Protector Pass-Through Laboratory Hoods offer sashes on two sides allowing operation on either side of the fume hood. An audible alarm sounds to prevent simultaneous opening of both sashes. With unobstructed visibility from either side, this hood is ideal for conducting chemistry demonstrations. …
-
For added mobility and flexibility Mystaire® offers a complete line of companion mobile carts for the Aura® Elite ductless fume hoods. The mobile carts are epoxy coated steel with locking casters. They are designed specifically for the Mystaire® Aura® Elite ductless fume hood.
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
AC600 Series Ductless Chemical Fume Hoods
AirClean® SystemsDesigned to provide a low cost chemical hood solution for protection of the operator and environment from toxic vapors, gases, fumes, and particulate. The AC600 Series ductless chemical workstation features the use of molded thermoplastics configured for a variety of common applications. Smaller in…
-
PowderSafe™ Type B Enclosures
AirClean® SystemsSeamless polypropylene construction provides the mass and vibration resistance crucial for accurate powder weighing, while the AirSafe™ automatic safety controller monitors airflow and filter conditions. The full rear-wall HEPA filtration zone moves powders and particulate away from the…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
Hoods for Exhaust Snorkels
INSTOCK LabsNederman Arms are supplied with a mini hood as standard - no extra extraction nozzle is required. The mini hood is also a universal interface for connecting to other hoods. A larger metal hood or transparent multipurpose hood can be attached directly to the mini hood, irrespective of arm size. The…
-
Protector Echo Filtered Fume Hoods
LabconcoThe Protector® Echo™ Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured fume hood that…
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
Back Mount Lab-Frame Kits for Fume Hoods
Lee EngineeringFrame Measures: 36" x 38" Chamfered Ends Rods are corrosion-resistant
-
SpillStopper™ Work Surfaces, 4' Wide
LabconcoSpillStopper Work Surfaces are molded from a special formulation of corrosion-resistant epoxy resins. They are dished and contoured to conform to the interior liner of Protector Laboratory Hoods. The front edge has a large radius to aerodynamically direct airflow into the fume hood. Pre-drilled…
-
The Protector XL Benchtop Laboratory Hoods offer superior design flexibility. Their panel liners are supplied in three depths to meet individual installation and application requirements. Protector XL Benchtop Laboratory Hoods are suitable for general chemistry applications. Features …
-
PowderSafe™ Type C Enclosures
AirClean® SystemsAirClean® Systems Type C PowderSafe ductless balance enclosures incorporate the airflow dynamics and HEPASafe™ features of the PowderSafe Type B with the user-friendly features and chemical fume containment capabilities of an AirClean Systems ductless fume hood. Thermally-fused…
-
Aura® Elite Ductless Fume Hoods
Mystaire®Constant Monitoring of Temperature and Humidity Mystaire® ductless fume hoods are self-contained, filtered enclosures that remove hazardous fumes, vapors and particles from virtually any laboratory application. Unlike traditional fume hoods there are no installation costs and no ductwork…
-
Dead Air Boxes
AirClean® SystemsAirClean® Systems Dead Air Boxes provide a circulation free environment with UV light sterilization. The Dead Air Box is standard with a 0-15 minute mechanical timer for sterilization between amplifications. A safety interlock switch prevents exposure to UV light when sash is raised. …
-
SpillStopper Work Surface molded of corrosion-resistant solid epoxy. Dished & contoured to conform to interior liner of Protector Pass-Through Hoods. Pre-drilled 2.5" (6.4cm) dia plumbing holes.
-
Clean Aire II Fume Hoods are a Class 1 ductless hood workstation with activated Carbon Filtration for fumes, odors, non-hazardous chemical vapors. This is a self contained ductless hood unit, equipped with integral carbon filter, vapor proof light, vertical sash and controls, and completely molded…
-
Protector Work Station Accessories
LabconcoFilters for Labconco protector work stations Impregnated charcoal filter packs remove dangerous vapors from the work area 5165N47 1 3/8” filters slip behind stainless steel grill to remove formaldehyde vapors quickly and completely
-
Guardian 500 Airflow Monitors
LabconcoApplicable Products: Fiberglass 30 Laboratory Hoods, Protector PVC Acid Digestion Laboratory Hoods, Protector PVC Perchloric Acid Laboratory Hoods, Protector Radioisotope Laboratory Hoods, Protector Perchloric Acid Laboratory Hoods, Protector XL Laboratory Hoods, Protector XLE Laboratory Hoods,…
-
Base cabinets built to last! UniLine Fume Hood Base Cabinets are constructed of top grade furniture steel and finished in a chemical resistant powder coated finish meeting or exceeding SEFA 8 recommended practice for laboratory casework. UniLine Base Cabinets set the standard for safety and…
-
Flexible Exhaust Duct, 10' length
Labconco10' length of 2" diameter steel-reinforced vinyl duct with 2 clamps.
-
The Protector® Echo™ Floor-Mounted Filtered Fume Hood combines the trusted filtration of Erlab’s Neutrodine® Unisorb Filter with the quality, innovation and energy-efficient fume hood designs of Labconco's unparalleled engineering to create an adaptable fully-featured…
-
Wash Rings
LabconcoWash Ring, wide angle conical spray nozzle, and wash water connection nipple are fabricated into a PVC coupling. For Stainless Steel or PVC Perchloric Acid Hoods. 10" Diameter Flow rate is one gallon per minute at 40 psi. 12" Diameter Flow rate is 0.70 gallons per minute at 20 psi.
-
Cyanoacrylate Fuming Chambers
Mystaire®Safely Fume Evidence with Consistent Results Mystaire® CA Series cyanoacrylate fuming chambers are the standard by which automated latent print development chambers are measured. The patented* recirculation filtration system with precise process controls for time, temperature and humidity…
-
Solid Epoxy Work Surfaces
LabconcoBlack chemical-resistant work surface is contoured to fit the dimensions of the enclosure and to contain spills. These surfaces can be used with Protector XVS Ventilation Stations, Protector Work Stations, Purifier Non-Ventilated PCR Enclosures and Tissue Culture Enclosures.
-
Canopy hoods are designed to collect and exhaust corrosive vapors, heat, steam, and odors when mounted over areas with water baths, hot plates, or portable equipment. Made of composite resin, the Canopy Fume Hood’s glass smooth surfaces provide superior chemical, corrosion and heat…
-
Recommended for low to moderately corrosive applications Intelli-Sense Multi-Speed Blowers are weatherized, direct drive, non-explosion-proof blowers controlled by a two or three position switch. Each blower has a reliable electronically commutated motor (ECM), which consumes one third less…
-
gGuard® Communication Software Automatically collects and records hood data, alerts and alarms on a customer-supplied personal computer Monitors, manages and provides data via email to a designated facility manager Provides access to the following: usage authorization, filter…
-
The Purifier Axiom Class II, Type C1 is the first biological safety cabinet that can be used in a recirculating Type A-mode for standard microbiological work, or can be connected to an exhaust system to function in Type-B mode for handling hazardous chemical vapors or radionuclides. Because of the…