Kemtech America Lab Glassware
-
SYNTHWARE Kugelrohr Distilling Bulbs
Kemtech AmericaKugelrohr Distilling Bulb Capacity: 5, 10, 15, 25 or 50mL available Joints: 14/20, Bulb O.D.: 25, 31, 35, 42 or 48mm available Overall Height: 80, 85, 90, 98 or 105mm available Used in distillation of very small amount of distillate at lower temperature with high efficiency.
-
SYNTHWARE Vacuum Jacketed Distilling Heads
Kemtech AmericaDistilling Head, Vacuum Jacketed Thermometer Joint: 10/18 Joints: 14/20 or 19/22 available For use with 25mm immersion thermometer.
-
Synthware Rotary Evaporator Anti-Splash Traps, Modified
Kemtech AmericaTrap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With two 4mm drain holes at the base of the inner tube to allow solvent to drain back into the evaporation flask. Has upper outer and lower inner standard taper joints.
-
SYNTHWARE Distillation Adapter
Kemtech AmericaDistillation Adapter, Microscale, Synthware, Joints: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
-
SYNTHWARE Short Path Vaccum Jacketed Distillation Apparatus
Kemtech AmericaUsed with 25mm immersion thermometer, and D27 distillation receiver.
-
Synthware Vacuum Adapters with Glass Stopcocks, Straight
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection 180 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
SYNTHWARE T-Shaped Connecting Tubes
Kemtech AmericaConnecting Tube, T-shaped, Synthware, Tubing OD: 8 and 10mm available.
-
SYNTHWARE Adapter with #15 O-Ring Joint to 10mm Hose Connection
Kemtech AmericaAdapter #15 O-ring joint to 10 OR 16mm Hose Connection
-
SYNTHWARE Shortpath Distilling Head for Volatile Distillants
Kemtech AmericaWith the condenser being a combination of a cold coil and Leibig. Top outer joint is a 10/18 for use with a 50mm immersion thermometer. With Vigreux Indentations.
-
Synthware Vacuum Adapters with Outer Joints & PTFE Stopcocks
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper outer joint. The PTFE stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
Synthware Vacuum Adapters with Glass Stopcocks, 90°
Kemtech AmericaSynthware vacuum adapter with a serrated hose connection turned 90 degrees to the standard taper inner joint. The glass stopcock has a 2 mm bore and is used to regulate the flow of gasses or liquids into reaction systems.
-
SYNTHWARE Vacuum Adapter with PTFE Stopcock
Kemtech AmericaVacuum Adapter, Microscale, PTFE Stopcock, Synthware, Joint: 14/10, Stopcock Bore: 2mm, Hose Connection OD: 8mm.
-
SYNTHWARE Solvent Still Head with Drainage Port
Kemtech AmericaSolvent Still Head Capacity: 500 and 1000mL available Top Joint: 24/40 Bottom Joint: 24/40 and 29/42 available Side Joint: 14/20 Drainage Port Joint: 14/20
-
Synthware Distilling Adapters, 75°
Kemtech AmericaSynthware distilling adapter with top compression cap. With same size standard taper inner joints on bottom and side arm. Cap accomodates 5.0 - 7.5mm O.D. thermometer. Supplied with one Nylon cap and one Viton o-ring.
-
SYNTHWARE Distillation Receiving Set
Kemtech AmericaComes with Synthware Distilling Adapter (Joints: 14/20 or 19/22) and Cow Receivers (Joints: 14/20 or 19/22). Designed without hose connection to be used with D10 distillation apparatus. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**
-
SYNTHWARE Inlet/Thermometer Adapter
Kemtech AmericaThermometer Adapter, Microscale, Synthware, Joints: 14/10, Thermometer OD: 5.0-7.5mm, supplied with one compression cap and one Viton O-ring.
-
Synthware Distillation Connecting Adapters
Kemtech AmericaSynthware distillation connecting adapter. With standard taper top outer joint and inner joints at bottom and the side arm. Bottom and side arm joints are angled at 75 degrees to one another.
-
Synthware Vacuum Take-Off Adapters with PTFE Stopcocks
Kemtech AmericaSynthware vacuum adapter with 2mm straight bore PTFE stopcock on the hose connection.The upper outer and lower inner standard taper joints are the same size.
-
Synthware Claisen Adapters
Kemtech AmericaProvides dual entry into a variety of flasks. Adapter has standard taper outer joints at top and on side and inner joint on bottom. All joints are the same size.
-
Synthware Kjeldahl Distilling Trap Adapters
Kemtech AmericaAdapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.
-
SYNTHWARE Short Path Distilling Head with 24/40 Joint
Kemtech AmericaOne-piece design for easy set-up. For the best result, use D272440 distillation receiver. To be used with 25mm immersion thermometer.
-
Synthware Vacuum/Inert Gas Adapters, 90°
Kemtech AmericaAllows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. Hose connection is at a 90 degree angle to the standard taper inner joint.
-
Synthware Inlet Adapters with Extended Length Lower Tubes
Kemtech AmericaSynthware inlet adapter with extended length lower tube. Allows for the introduction of reactants below the interior surface. Tube extends 153mm (6 inches) below the joint. Tubing has the same O.D. on both ends of the joint.
-
Synthware Distilling Adapters, 105°
Kemtech AmericaSynthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints.
-
SYNTHWARE Sublimators
Kemtech AmericaSublimator, Two Piece, Synthware, Various sizes are available. O-Ring Size: 217, 226, or 229, Clamp Size: 35, 65, or 75 available.
-
SYNTHWARE Snyder Distillation Column
Kemtech AmericaSnyder Distillation Column, 3 Section Top Outer Joint: 24/40 Lower Inner Joint: 24/40 Column Height: 150mm Overall Height: 300mm For use with Kuderna-Danish flask.
-
SYNTHWARE Micro Vigreux Distillation Head
Kemtech AmericaDistillation head with condenser sealed to a Vigreux column. Vacuum adapter has an outer joint and accepts a distribution adapter (D201414). To be used with a 25mm immersion thermometer.
-
Synthware Vacuum Adapters, Outer Joint
Kemtech AmericaSynthware vacuum adapter has a standard taper outer joint and a serrated hose connection. Ideal for use as a vent or for the introduction of pressure/vacuum.
-
SYNTHWARE Distillation Receiving Set
Kemtech AmericaComes with Synthware Distilling Adapter (Joints: 14/20, 19/22 AND 24/40) and Cow Receivers (Joints: 14/20, 19/22, AND 24/40). Rotating cow receiver allows four flasks to be progressively filled. **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**
-
Synthware Reducing Adapters
Kemtech AmericaSynthware reducing adapters are used for connecting dissimilar standard taper joint sizes. The lower inner joint is larger in size than the top outer joint.
-
SYNTHWARE Hickman-Hinkle Still Head with Side Port
Kemtech AmericaHickman-Hinkle Still Head, with Side Port, Synthware, Joint: 14/10, for microscale fractional distillation, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.
-
SYNTHWARE Vacuum Takeoff Adapter
Kemtech AmericaVacuum Takeoff Adapter, Microscale, Synthware, Joint: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.