Glass, jacketed reaction vessel design for use with our 7874 quartz and 7875 glass immersion wells. Instead of a standard taper joint, this reactor utilizes a height-adjustable, non-freezing #50 Ace-Thred. Also featured, a 14/20 angled joint for a sparger tube, a 24/40 vertical joint for a…

Ace Glass pressure tubes and bottles are the premier glass pressure vessels in the industry. Flat-bottomed bottles are rated at 60psi at room temperature while our tubes are rated at 150psi at as much as 120 degrees C. Due to varying conditions, Ace cannot guarantee glass vessels from breaking…

This conical 4" neck has three outer joints in line, plus a 14/35 outer joint which takes a 5021 Bushing Adapter to be used with ACE 8315 10/30 Thermometer. The 6500 Thermometer Well can also used with this head, when using a standard thermometer. For

NO-AIR storage tube with a 0-4mm Hi-Vac valve top with a 15mm o-ring joint sidearm. The valved top gives the researcher precise flow control and the o-ring joint facilitates connections to Schlenk lines. Supplied with a 7855-726 Fetfe o-ring.

With return line to allow excess solvent to return to boiling flask. Suitable for ASTM D 95 and E 123. Joints are 24/40.

With standard taper inner joint and twin hose connections opposite each other. Normally used with 6620 Reflux Apparatus to allow inert gas flow over top of apparatus to maintain oxygen free system. Hose connection is size C.

Full length, standard wall. U.S. Reissue Patent No. 22181. These famous ACE spherical joints are precision ground and vacuum leak-tested for fit and interchangeability. Available in both ball and socket members.

Glass joint, inner ground with ring on shank for use with threaded outer member or outer member with external thread for use with inner member.O-Ring and cap to form a leak tight-seal. For cap, see 7616; for O-Ring, see 7617.

With standard taper inner joint at bottom and side. Top has #7 Ace-Thred for use with 5029 Nylon bushing and adjustable length thermometer. Supplied complete with 5029-10 Nylon bushing and FETFE O-Ring.

Connecting, reducing adapter with top female joint being smaller than the bottom male joint.

90 degree adapter with either spherical to spherical ends or spherical to plain ends.

Four ring connector, (code -03 has three rings), is tooled with flare and exposed for direct sealing to apparatus. Tooled on each end of tubing with approximately 5-6" between connectors. Priced per dozen connectors (i.e., six doubles).

Interchangeable, ground joint bearing with jacket for water cooling. May be operated as high as 2000 rpm using our 8119 high-speed lubricant. Can be operated at 1500 rpm unevacuated using our 8117 Stir-Lube. Hose connections for use with 5/16" or 3/8"ID tubing. Available with PTFE clad joint to…

Glass standard taper joint adapters featuring a drip tip and right angle tee ground glass tube sidearms. The sidearms are used to make tube compression fitting connections to a wide variety of flexible and rigid tubing using our 12709,12711,12715 & 12716 product families of fittings.

A semi-micro sublimer used by a number of synthesis laboratories. The proportions have been found to be optimum for handling a variety of crystal types. The circulatory stem may be removed and collecting tube filled with dry ice, acetone, etc. Complete unit consists of body, head and circulatory…

With 24/40 standard taper inner joint and vacuum take-off. Hose connection is size D.

Complete, two-piece, plain flask, pressure reactor system designed to perform low to moderate positive pressure reactions, synthesis and catalysis. Reactor capacities range from 500ml to 5000ml and use Ace-Threds to achieve a leak-tight system. Two-piece (flanged flask and head) design allows the…

Used for collection and long-term storage of solvents. With standard taper 14/20 outer joint and 2 mm bore PTFE stopcock at top, double oblique 2 mm bore PTFE stopcock and standard taper 14/35 joint at bottom. Capacity is 250mL.

Angle adapter with 105 degree standard taper or spherical joint at top and bottom.

Bushing connector for joining an Ace-Thred to a reduced end tube. Assorted bushing and o-ring materials.

Septa tops are flanged with a sleeve-like extension that folds down over the vessel's neck. Punctured diaphragm re-seals after syringe is withdrawn. Septa are supplied in a variety of sizes, red, white or grey rubber.

Straight connecting adapter with standard taper inner joints at both ends. Various lengths.

75 degree adapter, standard taper top joint, standard taper or ball joint bottom and side.

With finger type condenser and 0-3 mm PTFE stopcock plug with PTFE ring seals for reflux control. The seals prevent O-Ring exposure to corrosive liquids and are backed up by a FETFE O-Ring. Thermometer joint is 10/30, all others are 14/20.

Adapter with ground joint at bottom and either a #11, #15, #25 or #36 Ace-Thred at top.,/p>

Process pipe, short radius elbow, 90 degree.

Process pipe reducing tee.

Gas collecting reservoir, described in Microscale Organic Laboratory, Mayo, Pike, Butcher, as a means of collecting and sampling gaseous products when using 9586 Capillary Gas Delivery Tube. Open-bottom tube has single line graduation at 3 and 4mL level and 20-400 thread at top. Supplied with cap…

Adapter with bent hose connection top and standard taper inner bottom joint.

With outer joint and external thread at top for making an O-RING-CAP-SEAL connection with mating male joints, inner joint at bottom and at 75 degree angle. Supplied with cap and O-Ring.

With upper joint at 105 degree angle. For operation other than at atmospheric pressure. Vacuum is applied to the side arm with the T-bore stopcock. The secondary receiver is vented by means of the lower stopcock. The capacity from the bottom of the drip to the stopcock is 2.5mL.Tubing connections…

A two-component system; cures to a film highly resistant to chemicals which tightly bonds the PTFE sleeve to glass. If sleeve is damaged, the epoxy may be removed with boiling formic acid and a new sleeve may be attached. Supplied in 30mL jars with activator in separate container. 30mL will cement…