General Lab Products
-
Large Flange Headplate Assembly w/ 18 Holes
Bellco GlassUniversal headplates can fit 5l to 36l vessels. Headplates are used with the large flange vessel to seal and to provide ports for access to the interior of the vessel. The 18-port headplate is most used since more components can be fitted into its ports. The impeller is always positioned in the…
-
Compression Fitting 2.5"
Bellco GlassBellco compression fittings are designed using our standard 45mm blue polypropylene open top caps and white silicone gaskets. A wide variety of fittings are available to allow ph and do monitoring via insertion of these probes into sidearms or vessels. Bellco probe adapters are designed to allow…
-
316l stainless steel bent harvesting tube for 5l flat bottom omni vessel. Use with large flange head-plate. Size: 1/2" x 16" Id: .430"
-
-
Large Flange Stainless Steel Clamp 8"
Bellco Glass200 mm SST large flange headplate clamp fits headplates, 5 liter thru 36 liter vessels. Corrosion resistant 316l stainless steel Includes red silicone o-ring and 200mm t-bolt clamp
-
Stainless Steel Bent Harvesting Tube 15L 1/4"x20"
Bellco Glass316l stainless steel bent harvesting tube for 15l flat bottom omni vessel. Use with large flange head-plate. Size: 1/4" x 20" Id: 5/32"
-
Stainless steel curved harvesting tube for 36l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 36l Dimensions: 1/2" x .430 x 24"
-
Valley Heating Blanket 115V-1L 75 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Watts: 75 Dimension (in.): 1.5" tall x 13 3/4" diameter 1 latch…
-
-
Stainless Steel 2- Port Assembly 500mL 100mm
Bellco GlassAll port assemblies are manufactured from 316l stainless steel and have an electropolish finish. 2- port assemblies have siphon and vent tubes. 3-port assemblies have siphon, fill tube and vent tubes. All port assemblies include a 45mm blue polypropylene screw cap and white silicone gasket. Size:…
-
Acrodisc Filter Barbed pkg. 4
Bellco GlassThe ptfe 50mm Acrodisc hydrophobic filter with hose barbs can be used to sterilize non-aqueous solutions, vacuum line protection, venting and gas filtration. Hose barb end allows easy secure attachment of silicone tubing or other types of tubing. The filter is non sterile and is autoclavable. Do…
-
Bellco Heating Blanket 230V-6L 300 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 8l Watts: 375 Dimension (in.): 3 x 26.5 2 latches 6ft…
-
-
Probe Holder 32mm
Bellco GlassIncludes gl32 blue open top polypropylene cap and white silicone gasket. The probe holder is designed specifically for the bio-probe low volume spinner flask. Also designed to secure ph and do probe into 32mm sidearms.
-
Impeller Assembly 25mL
Bellco GlassGlass shaft impeller assembly for 1967-style hanging bar spinner flask. Consist of ptfe magnet holder and ptfe coated magnet. Glass shaft ptfe magnet Size: 25ml
-
Metal Stone Sparger 36L For Flat Bottom Omni Vessels
Bellco GlassMetal stone sparger 36l for flat or round bottom omni vessels. Sparger inserts through stainless steel headplate fitting. 4 1/2?wide x 22? long 316 l stainless steel ra 32 finish or better Stainless steel frit
-
Valley Heating Blanket 115V-36L-HW 1200 Watt
Bellco GlassHeating blankets are designed to be used with a temperature controller and rtd temperature sensor for heating media inside a vessel to temperature. Male iec connector for use with temperature controllers Heating at 5 watts/sq.in. Flask size: 36l Watts: 1200 (not for CellTrol) see 1964-57365 or…
-
Large Flange Round Bottom Vessel 10L
Bellco GlassHeavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. Use with CellTrol ii only single or dual systems, and speed control modules.…
-
Flexgrip Chuck For 10mm Pestle Glass & Stirrer Rods
Bellco GlassIdeal use for pestle glass and stirrer rods. Used with homogenizer drive. Size: 10mm
-
3-Port Sparger Assembly w/ Frit 15L
Bellco Glass316-l stainless steel ra32 or better finish 10 micron porosity stainless steel frit for low profile vertical side arm vessels. Frit is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket Triple tube configuration with vent, fill/sample and sparge.
-
Large Flange Round Bottom Vessel 7L
Bellco GlassHeavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. Use with CellTrol ii only single or dual systems, and speed control modules.…
-
Stainless steel curved harvesting tube for 15l round bottom omni vessels. Manufactured from 316l stainless steel with ra finish of 32 micro inch or better inside and out electropolish finish. Size: 15l Dimensions: 1/4" x 5/32 x 22"
-
Flexgrip Chuck For 6mm Pestle Glass & Stirrer Rods
Bellco GlassIdeal use for pestle glass and stirrer rods. Used with homogenizer drive. Size: 6mm
-
Low Profile 3-Port Thermowell Assembly 6L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube. Port Thermowell assembly For low profile 3l vessel Material: 316l…
-
Stainless Steel 3-Port Assembly 6L
Bellco GlassSize: 6l Seam welded w/ electropolish finish 3-port w/ siphon, fill & vent tubes Includes: 45mm pp cap & silicone gasket Dimensions: 1/4" x 5/32" Longest tube: 10 1/2" at curve
-
Stainless Steel Shaft Assembly 3L
Bellco GlassManufactured from 316l stainless steel. Impeller assembly for micro-carrier spinner flasks. 1965 series micro-carrier spinner flask Size: 3l
-
Glass Ball Impeller Only 3L
Bellco GlassGlass ball houses a magnet for gentle agitation of micro-carrier beads and has a 70mm cap. Specially formed bottom indent prevents accumulation under the impeller. Cap size: 100mm Size: 3l
-
Low Profile 3-Port Sparger w/ Holes 6L
Bellco Glass316-l stainless steel ra32 or better finish .040? drilled holes sparger for low profile vertical side arm vessels. Threaded end is removable for cleaning. Comes with 45mm blue polypropylene open top cap and silicone gasket. Triple tube configuration with vent, fill/sample and sparge.
-
Micro-Carrier Impeller Assembly 15-36L
Bellco GlassImpeller assembly for micro-carrier spinner flasks. Consist of magnet holder, silicone plug, magnet, and ptfe paddle. Impeller size: 15-36l Paddle dimensions: 3"x 10"
-
English threads Fits into 3/8" holes in headplate material 316l SST with electropolish finish - ra 32 finish inside & out Inside dimensions: .250" od x 19 1/4" overall length insertion length: 18" with hose barbs supply with SST nut & o-ring
-
Flat Bottom Flange Vessel 3L
Bellco GlassHeavy walled construction for cell culture and fermentation applications. Heavy duty o-ring flange creates positive seal for stainless steel head-plate. For use with stainless steel head-plate, o-ring, and locking clamp. 5l flat bottom 215 x 250mm Large flange takes 200mm headplate Large flange…
-
Thermowell Assembly 1L
Bellco GlassThermowell assemblies are used to hold inside one tube the rtd temperature sensor that monitors the temperature within the vessel in conjunction with a temperature controller. There are also tubes for addition of media and vent tube Thermowell assemblies for 1965 and 1967-style angled sidearm…