Includes flexure analysis probe and 5mm platform. Permits deformation studies of films.

Replacement Crimper Head

Used with standard furnace, part of Quartz Parallel Plate SystemKit P/N N5390135.

Required for the expansion, penetration, compression and flexure modes of operation. Used with high temperature furnace, part of Quartz Parallel Plate System Kit (Product Number: N5390138)

TAGS Controls Up to Four Purge Gases for Operator Convenience Nitrogen, air, helium, and oxygen are typical purge gases used in thermal analysis experiments and often an operator has to manually switch between them. With TAGS, as many as four gases can be connected and the gases can be…

Autosampler Crimper Accessory Kit

Used for oxidation studies of metals, minerals, ceramics, clays and soils. They can also be used for melting and eutectic diagrams in the metals industry. The covers are pierced. A crimper is not required.

Aluminum Cylinder for Expansion Measurement

This tube differs from the standard sample tube in that the 10mm bending platform is permanently fused to the base of the sample tube. Used with the high temperature furnace.

Removes moisture and particulates from your purge gas. Includes all the necessary fittings needed to make pneumatic connections easy. Tape and tubing are not included.

Includes 100 volatile pans and pierced covers (50 micron diameter hole centered in the cover)

The Universal Crimper Press provides high quality sample crimping for the Autosampler sample pans and can crimp the standard aluminium pans, O-Ring sealed large volume stainless steel pans, and the 20mL volatile sample pans. This is achieved simply by using the appropriate sealing insert with the…

DMA 10 mm Height Calibration Cylinder

BOOK-DYN MECH ANAL PRACTICAL I

Sealing Inserts for Sample Pans.

Dewar Assy-DMA8000 50 Liter LN2

Quartz Extension Probe for DMA 7/DMA 7e and TMA 7

Force Calibration Weight, 50 g.

Window Quartz-Cover

Silicone o-ring, 9.25 mm inner diameter by 1.8 mm width, used with quartz torches in Optima™ 3x00 XL, 3x00 DV, 3000 SCX, 4300 V, 5300 V, and 7300 V ICP-OES series instruments.

5mm Knife Edge Bending Platform

DIE ASSY-DSC HIGH PRESSURE PAN

Includes: Intracooler Bolt Insulating Disk (P/N 03191720), Split Bushing (P/N 03191719), and Bolt (P/N 03191527)

Includes the TGA 8000 Sub-ambient Cooling Tube (N5370333), Hose clamps (09903004) and tubing (02506518) for connecting the Cooling Tube to the Chiller, and Instructions. When combined with the Chiller Accessory (N5370220 for 120V operation or N5370221 for 220 Volt operation) provides the ability to…

Includes plate and screws.

Pyris 1 DSC CryoFill Dewar Tank, 50 Liter

Permits deformation studies of films. Includes flexure analysis probe and platform.

Penetration and Compression: Narrow tip compression probes are available for penetration measurements. A broad tip compression probe permits the determination of the compressive modulus and additional properties of soft rubber materials. Part of Quartz 3-Point Bending Systems P/N N5390137 and P/N N5390136.

Universal DMA7/DMA 7e Probe Tip Holder for use with Stainless Steel Parallel Plate, 2-, 3-, and 4-Point Bending. Single and Dual Cantilever Measuring systems. Includes probe tip holder (P/N N5390104), collet (P/N N5391004), and lock nut (P/N N5391005).

For use with ice water bath or LN2

Includes six covers and six liners.

This 208-page comprehensive reference book handles the basic theory and practice of the dynamic mechanical analysis (DMA) technique. It gives the chemist, engineer, or material scientist a starting point to understand when and where dynamic mechanical analysis can be applied, how it functions, and…