Use for providing carrier, fuel, make-up, or auxiliary gases to laboratory instruments.

Use of these liners helps ensure an inert GC flow path for higher sensitivity, accuracy, and reproducibility. Consistent quality with exceptional batch-to-batch uniformity Low to zero bleed or background contamination

Caps not included (sold separately).

Never again will you burn your fingers removing a hot injection port liner. The Claw safely and cleanly removes liners, O-rings, or other small objects from the injection port. You can then place the hot objects in a clean 4 mL vial situated in The Claw holder until ready for reuse. Easily…

Easily loosens the liner cap from the injector Unique, ergonomic handle—easy to grip

Use of these liners helps ensure an inert GC flow path for higher sensitivity, accuracy, and reproducibility. Consistent quality with exceptional batch-to-batch uniformity Low to zero bleed or background contamination

Similar to the CG-4440 vacuum manifold, but with BOTH ENDS OF INERT GAS LINE OPEN to permit connection to the gas source and an oil bubbler. Hose connections have a 10mm small serration and a 11mm large serration.

Use of these liners helps ensure an inert GC flow path for higher sensitivity, accuracy, and reproducibility. Consistent quality with exceptional batch-to-batch uniformity Low to zero bleed or background contamination

Deactivated fused quartz helps eliminate activity for complete inertness along the GC flow path Universal fit: use with 0.1–0.53 mm ID Restek columns (0.33–0.74 mm OD) Optional Siltek deactivation is ideal for organochlorine pesticides analysis

Graphite Ferrules Preconditioned to eliminate outgassing. High-purity, high-density graphite. Smoother surface and cleaner edges than conventional graphite ferrules. Contain no binders that can off-gas or adsorb analytes. Stable to 450°C. Vespel/Graphite Ferrules …

Fuel-grade high purity hydrogen generators are safer alternatives to high-pressure gas cylinders. The new Proton Exchange Membrane (PEM) cell eliminates the use of liquid electrolytes with hydrogen generators. Deionized water is all that is required to generate hydrogen for weeks of continuous…

Withstands thousands of injections Eliminates septum coring and crumbling Reliable performance during extended runs O-ring detail seals needle during injection Duckbill seals more tightly at higher pressures Low insertion force for easy manual injections Reduced septum bleed and…

Needle guide allows easy penetration and prevents septum coring Manual injection septum nut allows use of 26-gauge needles for on-column injections Made of high-quality stainless steel

Ideal for high-flow split applications >500 mL/min on Agilent 5890 GCs Siltek treatment provides enhanced inertness versus stainless steel All seals include washers

Click-On traps measure: 8 1/2" x 1 1/4" (21.6 x 3.2 cm)

Agilent pistons are made from a high purity, monocrystalline sapphire for maximum durability. Although ceramic pistons can be manufactured at a lower cost, ceramic is a sintered, polycrystalline material, which can cause undesirable variations during the production process. Agilent seals are…

Fit split (6.3 mm OD) or splitless (6.5 mm OD) liners.

High-quality wrenches for tightening capillary fittings.

PTFE impeller for use with over head drive motor and drive adapter in 3L low profile bioreactor vessel. Specifications: Size: 3-6L

Whether you need to increase your system sensitivity with large volume injection capabilities, analyze thermally labile compounds or inject dirty samples, the Multimode Inlet delivers the performance and flexibility you need. Agilent Technologies products are intended for sale/shipment…

The advantages of the Merlin Microseal septum include elimination of septum coring; longer life; and consistent, low needle-insertion force. The Microseal septum incorporates two separate sealing mechanisms. These sliding seals eliminate septum coring and the resulting accumulation of septum crumbs…

With #7 Ace-Thred end valves that insure tight fit without grease. No stopcock plugs to pop out. Nylon bushing tightens into the internally threaded glass to form an O-Ring compression seal. Each bulb has a syringe sampling port and is supplied with two bushings, two FETFE O-rings and one septum.…

0.018-inch ID jets: Used for most general-purpose packed column applications 0.030-inch ID jets: For packings that exhibit high bleed and that frequently clog the tip of smaller 0.018-inch jets Standard Version Threads specially coated for easy installation and removal Special…

Unlike brass brushes that can leave a metal residue, these stainless steel tube brushes (3/8-, 3/16-, and 1/4-inch) work well for cleaning dirty collectors, injector ports, and detector ports. The surface brush can be used to remove residue that builds up on metal detector jets and electronic contacts.

fits 8 mm OD liners

Supplies for 255 Nitrogen Chemiluminescence Detector (NCD). This nitrogen-specific detector is based on a chemiluminescent reaction; complex sample matrices can be analyzed. Agilent Technologies products are intended for sale/shipment within the US only. International customers should…

Made from high-quality stainless steel Meets original manufacturer's equipment performance

Never worry again about burned fingers or having to wait for the injector to cool down. The Hot Swap capillary column nut allows you to change your capillary column while the injector temp is still hot. No more burned fingers! No more downtime waiting for injector parts to cool down. …

Pressure release seals are designed to open when the internal pressure exceeds 3.0±0.5 bar.

Parker’s (A-Lok) fittings are ideal for installing new equipment, modifying existing instrumentation, or replacing worn connections. Fittings are available in brass and stainless steel. Siltek/Sulfinert treated or Silcosteel-CR treated fittings are also available. If there is a particular…