Cylindrical with standard taper joint top and bottom and drip stem. Stopcock has glass plug. Drip stem does not extend beyond joint, thereby eliminating possible source of breakage. For same funnel with 1:5 PTFE plug, see 9491.

Pressure equalizing, addition funnel featuring standard taper joints, protected drip-tip, equalizing arm and double scale graduations calibrated from the stopcock. Available PTFE stopcock styles are standard, metering or needle valve. Top stopper is not included.

Microscale, vacuum adapter with vertically adjustable Hirsch filter funnel that is suitable for use with all Microscale flasks and vials with 14/10 joints. Two-piece adapter features a #7 Ace-Thred at top with a Nylon bushing and O-Ring that forms a compression seal with funnel stem, bottom joint,…

European style funnel with new leak-tight, locking stopper that will not fall out during shaking or transportation. Outer ground joint at top is a Rodaviss joint. Stopper can be secured in top joint via cap and O-ring for a positive, leak-tight seal; n

Borosilicate glass addition funnel with integral fritted disc. Has outer top standard taper joint, an inner standard taper joint bottom,a 2mm glass stopcock arm at top and a 0-4mm Hi-Vac valve bottom outlet. Ideal for either vacuum or Schlenk lines. Top and Bottom joints are the same size.

Borosilicate glass wide mouth funnels with a Duran flange bottom. Flange matches side ports on 6530 Ace Glass reactor heads. Funnel is slightly angled to allow for easy pouring of material into large scale reactors. Uses 6517 quick-release clamp.

Graduated addition funnels similar to 7268 series, except with outside jacket for cooling and/or heating. Jacket extends from just below shoulder of vessel down to the bottom tube just below the stopcock. Stopcock is either 2 or 4mm bore PTFE plug. Bot

Pear shaped, with joint and drip tip, supplied with glass plug.,/p>

Glass powder funnel used for the addition of material to containers with standard taper joints. See Ace 7242 family for funnels without joints.

Borosilicate glass addition funnel. Has either a 2mm glass stopcock or a 0-3mm inlet valve side arm. Has an outer standard taper joint top. Funnel has a 0-4mm Hi-Vac valve bottom outlet ending in an inner standard taper joint. Ideal for Schlenk lines or using to connect or add on to vacuum and…

Graduated addition funnel featuring standard taper joints,graduations in both ascending and descending volume,protected drip tip and a glass stopcock. Graduations are calibrated from the stopcock.

Used for pouring liquids or powders into multineck flasks. Available with standard taper joint.

Side operated screw feed instrument for addition of powders and solids, up to 25 mesh, to reactions without problems of seizing or binding. Features a flexible PTFE screw thread wrapped on a precision PTFE-ceramic shaft and contained within a precision bore housing.This offers a unique flexibility…

With 14/10 inner joint. Top diameter is 40 mm.

Cylindrical with joint at top and bottom, drip stem, and double scale graduations, calibrated from stopcock. Drip stem does not extend beyond the joint, thereby eliminating a possible source of breakage. PTFE or metering valve stopcock plug.

Used for pouring liquids or powders into multineck flasks.

Cylindrical, graduated reservoir permits determination of volume added at any time during pumping cycle. By stopcock manipulation, material may be pumped from graduated (10mL in 0.1mL) side tube only. This permits obtaining accurate pumping rate over short periods of time. Top joint is 24/40 outer.…

With an equalizing arm and a special stopper so that material may be isolated from the atmosphere. Turning the stopper completely closes the vessel to the equalizing arm so that the funnel may be disconnected without exposing contents to moist air, etc

Cylindrical with standard taper joint top and bottom and drip stem. Stopcock has 1:5 PTFE plug. Drip stem does not extend beyond joint, thereby eliminating possible source of breakage. For same funnel with glass plug, see 9490.

Jacketed version of 7297 series addition funnels. Jacket runs from shoulder at top of vessel to above the PTFE stopcock. Has size D hose barbs for 3/8in ID tubing. Pressure equalizing arm runs from top of vessel to just below the PTFE stopcock. Graduat

Graduated Instatherm® addition funnel provides precise heating for reactor systems demanding heated or constant temperature for the added reactants. Funnels feature standard taper outer top joints and bottom PTFE stopcock inner joints. All funnels include a 9698-20 connecting controller cord.

With jacket for cooling or heating. All porosities of a given size are priced the same. Hose connection is size C.

Diameter of sintered glass filter disc is 18mm. Measures 40mm from disc to bottom of joint. All porosities of a given size are priced the same. Volume approximately 10 mL. Hose connection is size A.

Side operated screw feed instrument for addition of powders and solids, up to 25 mesh, to reactions without problems of seizing or binding. Features a flexible PTFE screw thread wrapped on a precision PTFE-ceramic shaft and contained within a precision

Threaded stopcock with PTFE plug permits smooth needle valve adjustment down to 0.1cc/min. flow rate. Double PTFE ring seals prevent exposure of backup O-Ring to corrosive liquids. Angled position makes manipulation of stopcock easier than conventional style. 24/40 joints top and bottom, double…

Cylindrical wtih standard taper joint top and bottom, drip stem, pressure equalizing arm and double scale graduations, calibrated from stopcock. Drip stem does not extend beyond joint, thereby eliminating possible source of breakage. Stop cock availab

Standard taper jointed powder funnels are fabricated with heavy walls for greater durability when pouring powders or liquids into ground joint containers.

Similar to 9495, except lower stopcock is solid 1:5 PTFE metering valve, side arm plug is regular 1:5 solid PTFE. For replacement plugs, see 8232 or 8224.

Powder funnel with standard taper joint and one flattened side for easy of use with multi-neck flasks.

Large separatory funnel for use where large volumes are needed. Cylindrical shape necks down to a #25 Ace-Thred and connects to an 8mm bore PTFE-clad glass stopcock via a PTFE coupling using FETFE O-Rings. The system is completely grease-free. Complete

Separatory funnel featuring a PTFE stopcock and a PTFE stopper included. See Ace family 12632 for extra stoppers.

Cylindrical with standard taper joint top and bottom and drip stem. Stopcock has glass plug. Drip stem does not extend beyond joint, age. Stopcock available with glass plug or 1:5 PTFE plug. thereby eliminating possible source of breakage. For same fun