Ace Glass Filtering Funnels & Adapters
-
Jacketed version of 7297 series addition funnels. Jacket runs from shoulder at top of vessel to above the PTFE stopcock. Has size D hose barbs for 3/8in ID tubing. Pressure equalizing arm runs from top of vessel to just below the PTFE stopcock. Graduat
-
Cylindrical, graduated reservoir permits determination of volume added at any time during pumping cycle. By stopcock manipulation, material may be pumped from graduated (10mL in 0.1mL) side tube only. This permits obtaining accurate pumping rate over short periods of time. Top joint is 24/40 outer.…
-
Funnel, Pressure, Equalizing
Ace GlassCylindrical with standard taper joint top and bottom and drip stem. Stopcock has glass plug. Drip stem does not extend beyond joint, thereby eliminating possible source of breakage. For same funnel with 1:5 PTFE plug, see 9491.
-
Funnel, Addition, Pilot Size, Ace-Thred
Ace GlassLarge separatory funnel for use where large volumes are needed. Cylindrical shape necks down to a #25 Ace-Thred and connects to an 8mm bore PTFE-clad glass stopcock via a PTFE coupling using FETFE O-Rings. The system is completely grease-free. Complete
-
Funnel, Addition
Ace GlassWith an equalizing arm and a special stopper so that material may be isolated from the atmosphere. Turning the stopper completely closes the vessel to the equalizing arm so that the funnel may be disconnected without exposing contents to moist air, etc
-
Funnel, Filter, Buchner
Ace GlassWith ACE fritted disc. Porosities A, B, C and D are priced the same.
-
Funnel, Separatory, PTFE Plug
Ace GlassSeparatory funnel features a PTFE stopcock and a standard taper joint with drip tip. Stopper is not included.
-
Funnel, Pressure, Equalizing, Graduated
Ace GlassPressure equalizing, addition funnel featuring standard taper joints, protected drip-tip, equalizing arm and double scale graduations calibrated from the stopcock. Available PTFE stopcock styles are standard, metering or needle valve. Top stopper is not included.
-
Funnel, Addition, Graduated
Ace GlassCylindrical with joint at top and bottom, drip stem, and double scale graduations, calibrated from stopcock. Drip stem does not extend beyond the joint, thereby eliminating a possible source of breakage. PTFE stopcock plug.
-
For use with ACE Pressure Reactors. Heavy wall funnel has a #15 Ace-Thred at top that can be stoppered using 5846 Plug, not supplied. Bottom drip tip is long enough to be secured in the #15 Ace-Thred on 6433 Reactor Head or One-Piece Reactor and has a bump and groove that restricts blowout when…
-
Funnel Addition, Jacketed
Ace GlassGraduated addition funnels similar to 7268 series, except with outside jacket for cooling and/or heating. Jacket extends from just below shoulder of vessel down to the bottom tube just below the stopcock. Stopcock is either 2 or 4mm bore PTFE plug. Bot
-
Funnel, Addition, Graduated
Ace GlassCylindrical with joint at top and bottom, drip stem, and double scale graduations, calibrated from stopcock. Drip stem does not extend beyond the joint, thereby eliminating a possible source of breakage. Metering valve stopcock plug.
-
For replacement stoppers, see 12633 or 12635. For stopcock plugs, see 8224.
-
Funnel, Powder, Offset
Ace GlassUsed for pouring liquids or powders into multineck flasks. Available with standard taper joint.
-
Funnel, Addition, 1:5 PTFE Plug
Ace GlassShort stem, addition funnel with ptfe stopcock plug included. 14/20 top and bottom joints. Stopper (8255-10) is not included.
-
Borosilicate glass addition funnel with integral glass fritted disc for filtering out material. Top has inner standard taper joint. Funnel has side arm with 2mm glass stopcock. Bottom outlet has a 0-4mm Hi-Vac valve for precise control and ends in an inner standard taper joint. Both upper and lower…
-
Borosilicate glass addition funnel. Has either a 2mm glass stopcock or a 0-3mm inlet valve side arm. Has an outer standard taper joint top. Funnel has a 0-4mm Hi-Vac valve bottom outlet ending in an inner standard taper joint. Ideal for Schlenk lines or using to connect or add on to vacuum and…
-
Cylindrical, with standard taper 24/40 joint top and bottom. Supplied with 1:5 PTFE stopcock plugs which require no lubrication. Stopcock on equalizing arm permits filling funnel without having to open the system to atmosphere. Drip tip does not extend
-
Funnel, Pressure Equalizing, Graduated
Ace GlassCylindrical wtih standard taper joint top and bottom, drip stem, pressure equalizing arm and double scale graduations, calibrated from stopcock. Drip stem does not extend beyond joint, thereby eliminating possible source of breakage. Stopcock supplied
-
Funnel, Pressure Equalizing, Graduated
Ace GlassCylindrical wtih standard taper joint top and bottom, drip stem, pressure equalizing arm and double scale graduations, calibrated from stopcock. Drip stem does not extend beyond joint, thereby eliminating possible source of breakage. Stop cock available with glass plug, 1:5 PTFE plug, pr PTFE…