Coil style reflux condenser with tightly wrapped coil providing maximum cooling. Excellent for use with high vapor pressure solvents. Condenser has a top outer standard taper joint and lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

LIDS, REACTORS, 6-NECK FOR 57MM OD REACTION VESSEL BODY, EQUIVALENT TO METTLER EASYMAX, Reaction Vessel Lid, 6-Nk, for 57mm OD Reactor Body: 14/20 Outer CN, (3) 14/20 Outer SN's, and (2) 10/18 Outer SN's; Equivalent to Mettler  Easymax® Part # 51161619Mettler Easymax® is a…

Two piece cold trap style condenser for use with rotary evaporators. Condenser has a 50mm flange on the side, a 35/20 lower ball joint, a 19/38 stopcock plug and removable hose connections using GL-14 threads.

Reflux condenser similar to CG-1213 but with detachable hose connections. Connections are made of polypropylene and provide a safe and easy way of connecting and disconnecting flexible tubing to the condenser. Hose connections have an O.D. of 8mm and an I.D. of 4mm. Supplied complete with two GL-14…

Static Waterless Allihn style reflux condenser with a standard taper outer joint at the top and a lower inner drip tip joint and GPI thread on side for filling the condenser with ethylene glycol. Supplied with open top cap and septa for closing off once the condenser is filled. No issues with…

Similar to CG-1210 but with the 24/40 outer joint replaced with a serrated hose connection for use with a drying tube. This style condenser is used primarily in Soxhlet extractions or in reflux mode. Hose connections have an O.D. of 10mm at the middle serration.

Condenser for use in refluxing from 1 to 20mL of solvent in flasks having a capacity of 5 to 50mL. Minimal surface area provides for better yields while providing adequate cooling. The additional hose connection is provided to allow introduction of an inert gas such as nitrogen. Top hose connection…

Double coil condenser for use with rotary evaporators for cooling with tap water in a vertical position. Condenser has a 45/40 lower inner drip tip joint, a 29/32 top outer joint, and removable hose connections using GL-14 glass threads. Condenser is supplied complete with plastic caps and serrated…

Two piece cold trap style condenser for use with rotary evaporators. Condenser has a 50mm flange on the side, a 35/20 lower ball joint, a 19/38 stopcock plug and removable hose connections using GL-14 threads. Condenser is supplied complete with PTFE centering ring along with plastic caps and…

Graham Condenser Joints: 14/20, 19/22 and 24/40 available Jacket Length: 120, 200, 250, 300 and 400mm available Hose Connections: 8 or 10mm available **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

Condenser has a large opening at the top for use with dry ice/acetone or liquid nitrogen. Condenser has an outer standard taper joint set at a 75º angle to the condenser body and a lower inner drip tip joint, both being the same size.

Graham condenser is designed for use in distillation applications. Constructed of borosilicate glass, this condenser has a coiled inner tube to provide additional surface area for highly efficient cooling. Socket is 24/40 with a screw thread connector.

Jacket has an O.D. of 40mm while coil O.D. is 8mm to provide maximum cooling capacity.

Reflux Solvent Still, Microscale, Synthware, Capacity: 25mL, Joints: 14/20, Stopcock Bore: 2mm.

Molded inner cold finger for use in fabrication of Friedrich style condensers. Overall length is 230mm with an outside diameter of 45mm. NOTE: TOP IS UNFINISHED.

Microscale air condenser normally used in reflux experiments. When packed with desiccant material, condenser becomes a drying tube. With inner joint at bottom, outer joint at top. Codes -10, -14 and -17 supplied with drip tip for use with 9595 Spinning Band Column. Effective length, approximately…

These PYREX® West condensers are designed with a 190mm long jacket that has a 14/20 Standard Taper top joint. The bottom has 14/20 Standard Taper inner joint with a drip tip. The tubulations are on the same side to reduce breakage. The tubulation O.D. is approximately 10mm. This condenser is a…

Bulb type for use with regular extraction apparatus. Improved design permits greater condensing capacity. Jacket lengths approximately 255mm with one bulb per 50mm.

Friedrichs Condenser, Joint: 24/40, Overall Height: 330mm, Hose Connection: 10mm

This PYREX® general purpose condenser can be used for either distillation or extraction. Although the condensing area per unit length of the 200mm long jacket is low, the large capacity water jacket gives efficient cooling. Condenser tubulations are approximately 10mm O.D. The adapter end is…

Condenser has a standard taper outer joint at the top and a lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

High through-put, double coil condensers are designed to fit larger systems and pilot plant reactors. The design is similar to a rotary evaporator type condenser, where large volumes of material are being condensed at high temperatures and where large

Two piece cold trap style condenser for use with rotary evaporators. Condenser has an additional 19/38 outer joint sealed onto the condenser to allow continuous feed of volumes exceeding the capacity of the evaporating flask.

Replacement, borosilicate glass components for R220 rotary evaporators Product offering includes triple coil condensers, Bullfrog condensers and the lower condensate coolers for rotary evaporators. Available in either plain or safety coated versions. Units include black SVL caps & red GL thread…

Condenser has a top standard taper outer and lower inner drip tip joint. Hose connections have an O.D. of 10mm at the middle serration.

With small ball joints to prevent mineral oil being sucked back under sudden negative pressure in the system.

Condenser for use in cooling of the scrubbing fluid. Graham coil type condenser having 1/2" Swagelok® tubing for use with CG-1975-20 compression fitting. Overall length is ~350mm with effective length of 250mm. Hose connections have 9mm OD small serration and a 10mm OD large serration.

Double coil condenser for use with Buchi rotary evaporators for cooling with tap water in a diagonal position. A 19/38 top valve. With 35/20 spherical ball joint.

Borosil® Liebig Condensers have an interchangeable inner and outer joint with a drip tip. This simple design has a thin wall for the inner tube, facilitating efficient heat transfer with a low cooling capacity. Most common forms of use are distillate separation. The outer glass tube has two…

With top joint jacketed for water cooling. Jacket length measured from bottom of top joint.

Distillation Condenser, Vacuum Jacketed, Joints: 14/20 and 24/40 available, Jacket Height: 130mm and 250mm available, with 12mm ID indentations to support packing material **NOTE THESE PRODUCTS COME IN DIFFERENT SIZES - WHAT IS PICTURED MAY NOT BE THE ITEM SOLD**

Ai SolventVap 2L (evaporating flask capacity) series rotary evaporators come with a modular heating bath, vertical glassware, and digital temperature/rotation control. Its optimized bath volume allows for rapid heat-up times. Thats why our SolventVap evaporators consistently deliver reliable and…