Clamps/Supports

Compare Tool

Select up to 3 products

HomeAll Products

Clamps/Supports

1 - 32 of 312
Sort
View
Show
  • Double Burette Clamp

    GSC International, Inc.

    The clamp holds a burette securely while allowing full view of the burette graduations. The clamp accepts rods from 1/4" to 1/2" in diameter. The clamp has an enamel finish with rubber coated grips to prevent slippage.

  • Table Clamp

    Humboldt

    The Table Clamp is designed to support meter sticks and other round or square rods, either vertically or horizontally up to 1" (25mm) thick. The Vee's are milled at right angles and the clamp can be mounted on table edges up to 1-3/4" (45mm) thick. Each jaw can be adjusted separately. Heavy cast…

  • Plastic Joint Clips

    Bal Supply

    Standard taper keck type joint clips Color coded for easy size identification Will not corrode or scratch glassware Can withstand temperatures up to 302°F (150°C)

  • Stainless Steel Ball & Socket Clamps

    Bal Supply

    Stainless steel Pinch clamps are for use with O-ring and ball and socket clamps All sizes except 1236D18 and 1236D20 have screw locking devices. Only screw locking clamps are recommended for O-ring joints. All clamps are made of 304 –18/8 Stainless Steel.

  • Talboys Staining Rack

    Ohaus

    Slide Staining Rack Constructed of stainless steel, the Talboys Slide Staining Rack will resist corrosion under normal use. Adjustable to fit trays or sinks up to 533mm (21") inside.

  • Test Tube Clamps

    GSC International, Inc.

    Nickel plated steel. Overall length 5".

  • Support Stands with Rods

    United Scientific Supplies

    These support stands with rods come complete with a stamped steel base with black enamel finish and a removeable zinc plated steel rod.

  • Fixed-Position Clamps

    Ohaus

    Used to hold apparatus near the lab-frame where no adjustment is required after set-up. Built-in holder grips rods up to 19mm (0.75") in diameter Fixed-Position Clamps have an integral holder but can be rotated after attachment to a lab-frame or other apparatus. Available in 2-prong or…

  • Stainless Steel Lab Frame Lattice Rods

    Lee Engineering

    Thomas No. 1177P04: 1/2" X 4" Rod Thomas No. 1177P05 : 1/2" X 12" Rod Thomas No. 1177P06 : 1/2" X 24" Rod Thomas No. 1177P07 : 1/2" X 36" Rod Thomas No. 1177P08 : 1/2" X 48" Rod Thomas No. 1177P09: 1/2" X…

  • Support Stands with Rod and Rings Sets

    United Scientific Supplies

    Each set contains a stamped steel base and rod along with 2, 3, 4, or 5 cast iron rings with clamps. Sets are shipped in specially designed boxes.

  • LabJaws Connectors & Holders

    Ohaus

    Regular Clamp Holders Stainless steel electro-polished finish or nickel-plated zinc construction. Ideal for holding clamps to lab-frames. Use wherever clamping at 90° is required. Swivel Holders Two rod holders with center swivel capacity allow tilting of clamps at any angle in…

  • Rod Coupler, Aluminum

    Lee Engineering

    Extend the length of your lab frame rods. This strong, corrosion-resistant aluminum alloy connector permits end-to-end joining of 12.7 mm (1/2") rods in diameter. Precision machining ensures rod alignment. Comes with two tee handles for adjustment.

  • 12 Cylinder Bench Clamp

    Ohaus

    Model 712 is a rugged cast aluminum clamp that safety secures gas cylinders to benches, tables, or other flat surfaces up to 2.5" (64mm) thick. The 1" (25mm) wide, 54" (1372mm) long nylon strap features a nickel-plated, non-slip spring catch and buckle for easy adjustment around…

  • Open Lab Rod Connector for Lab Frame Assemblies

    Lee Engineering

    Joins rod frames in different planes. Open throat construction permits rods to be lifted out without having to be pulled through. Setups can remain unchanged when shifting individual members. Accommodates 12.7 mm (1/2") rod. Rods are locked with 14"-20 hex screws. Stainless steel. Handle…

  • Test Tube Clamps

    Humboldt

  • Scienceware® Pinchcock Tubing Clamp

    Bel-Art Products

    One piece pinchcocks molded of autoclavable white polycarbonate Release by thumb pressure 2848W26 Mini Clamp is single position on-off clamp; for use with thin-wall tubing less than 3/16” o.d. 2848W30 Clamp is 15-position ratchet- type for one-hand, stepwise flow control…

  • Lattice Lab System, Set #3

    United Scientific Supplies

    This Lattice Lab System features an assortment of aluminum rods from 18" to 48" long including 10 rods that are 48" long.  Assembly is easy and requres only a screwdriver.  Support rods are made of hard aluminum and foot plates and hook connectors are made of cast…

  • Stamped Steel Base Support Stand

    GSC International, Inc.

    Support Stand made from a stamped steel with an enamel finish that is acid resistant. Includes a zinc plated steel rod that screws into the base support. Available in the following sizes: 4x6" Base, 5/16" x 18" Rod 5x8" Base, 3/18" x 20" Rod …

  • Screw Compressor Clamp, Swivel Lower Jaw (Hoffman)

    Humboldt

    Screw Compressor Clamps are used to control the flow in flexible tubing. The clamps have a machined adjustment screw to permit accurate regulation of the flow. All corners are rounded to prevent cutting of the tubing. The clamps feature brass construction that is plated for corrosion resistance and…

  • Clamp Extension

    GSC International, Inc.

    A cast aluminum clamp with cork lined prongs to hold a flask securely. The jaws open to a maximum of 3". Overall length 9.5".

  • Funnel Support

    Humboldt

    The Humboldt Funnel Support is designed to accept up to four funnels. The unit consists of a hard wood support with four slotted holes and a metal clamp with thumbscrew for support rod mounting.

  • Round Bottom Flask Stand

    United Scientific Supplies

    Molded in Polypropylene, this flask stand gives a stair-like top view. Every step provides excellent support to the round bottom flask at every point of contact. This flask stand can hold round bottom flasks up to 10,000ml capacity. This stackable flask stand can also be autoclaved.

  • stop-it Hose Clamps

    Bürkle

    Easy-Click closure - stop-it can be opened and closed in any position - without tiresome screwing on and off. High quality material - stop-it made from the heat resistant and chemical resistant plastic PVDF. The clamp is galvanised steel. The hose clip can be used wherever the flow in hoses…

  • Ultra Flex Support System With Lab Frame Connector

    Ohaus

    Mounts to lab-frames or support stands Suitable for use in fume hoods 3 types of clamp heads Support system securely attaches to support stands, lab-frames, or any support rod up to 0.75” (1.9 cm) in diameter.  Ultra Flex clamping system is extremely versatile. Flexible arm…

  • Cast Iron Support Stands with Rods

    United Scientific Supplies

    These support stands feature a heavy cast iron base with black enamel finish. Each base includes a removable zinc plated rod.

  • Aluminum Lab Frame Lattice Rods

    Lee Engineering

    L12R-4A : 1/2" X 4" Rod L12R-12A: 1/2" X 12" Rod L12R-24A: 1/2" X 24" Rod L12R-36A: 1/2" X 36" Rod L12R-48A: 1/2" X 48" Rod L12R-72A: 1/2" X 72" Rod L12R-84A: 1/2" X 84" Rod L12R-60A: 1/2" X…

  • Thomas Spherical Joint Pinch Clamps

    Thomas®

    For ball-and-socket or O-ring glass joints in universal use for quick, convenient and safe mounting and dismantling of apparatus Strong, linear spring closing action Unique forked-shaped jaws provide uniform compression for safe, leak-free seals Screw-locking device with spring for…

  • Flow Control Adapters with Spherical Joints

    Chemglass

    Flow control adapter for use with CG-1198 and CG-1199 chromatography columns along with CG-1200 reservoir. Adapter has a 0-4mm Chem-Cap® metering plug.

  • BIBASE rubber support ring

    MilliporeSigma

    Reversible; can also be stacked upon each other. Three sizes provide six different diameters for round-bottom flasks ranging from 50 to 6,000 mL. Excellent adhesion to glass prevents slippage and also offers thermal and electrical insulation. Available in two rubber types.

  • SYNTHWARE Joint Clamps

    Kemtech America

    Joint Clamp, Standard Taper, Plastic, Synthware, Various Joint Sizes Available.

  • Connector, T-Type

    Harvard Apparatus

    Made of glass-filled nylon For mounting clamps and adapters that have a male connector to vertical lattice rods or laboratory stands One end has open side to clamp rod up to 1/2” (13 mm) diameter and lock with thumbscrew. Opposite end has female socket 3/4” (19 mm) deep…

  • Connector, End-to-End

    Harvard Apparatus

    Of glass-filled Nylon with stainless steel thumbscrew shafts For joining rods of the same or varying diameters, end to end Takes rods up to 1/2” (13 mm) diameter Center barrier within connector prevents rods from touching Each rod held by separate thumbscrew …

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.