Bottles

Compare Tool

Select up to 3 products

Sort
View
Show

Greenwood

  • Gay-Lussac Specific Gravity Bottles

    Wilmad-LabGlass - SP Scienceware

    These unadjusted borosilicate glass specific gravity bottles determine the density of liquid samples. They have capillary stoppers, and ground Standard Taper joints to reduce evaporation.

  • Gay-Lussac Adjusted Specific Gravity Bottles

    Wilmad-LabGlass - SP Scienceware

    These borosilicate glass specific gravity bottles are accurately adjusted at 20°C to determine the density of liquid samples. While the joints have Standard Taper dimensions, the capillary stoppers are not interchangeable since the final adjustment for volume is made on the stopper. Each bottle…

  • Precision Rubber Septa Caps

    Wilmad-LabGlass - SP Scienceware

    Engineered for a "push on" fit in NMR tubes and ampules. The unique design provides a penetration point for cannulation and a dual seal inside the tube and on the outer sleeve. Will not break delicate, thin-wall tubing. Manufactured from one certified raw material formulation for absolute…

  • Low Form Weighing Bottles with Stopper

    Wilmad-LabGlass - SP Scienceware

    With closed bottom standard taper pennyhead style stopper Pennyhead stopper forms a secure seal Wide opening for easy addition and removal of samples Light weight for simple tare settings Manufactured from ASTM Type I, Class A borosilicate

  • Le Chatelier Specific Gravity Bottle

    Wilmad-LabGlass - SP Scienceware

    Used to determine the specific gravity/density of sand, cement and other fine materials, this borosilicate glass specific gravity bottle is developed from ASTM C 188 and ASTM E 694. The body holds approximately 250mL and the capacity of the oval bulb in the neck is 17mL. Volume below the bulb is…

  • High Form Weighing Bottles with Stopper

    Wilmad-LabGlass - SP Scienceware

    With closed bottom standard taper pennyhead style stopper Pennyhead stopper forms a secure seal High form shape decreases bottle footprint Light weight for simple tare settings Manufactured from ASTM Type I, Class A borosilicate

  • Parr Weighing Bottles with Flat Top Cap

    Wilmad-LabGlass - SP Scienceware

    Caps can be used as weighing dishes External standard taper joint allows for sample transfer without seal interference Flat top permits stacking for increased desiccator capacity Light weight for simple tare settings Manufactured from ASTM Type I, Class A borosilicate

  • Gas Collecting Tubes

    Wilmad-LabGlass - SP Scienceware

    Featuring a side outlet in the body for a self sealing syringe stopper, these borosilicate glass Gas Collecting Tubes are useful in gas chromatography or mass spectroscopy. Stopcocks have PTFE plugs. For additional rubber stoppers, see ML-1940.

  • Carboy with Hose Connection

    Wilmad-LabGlass - SP Scienceware

    Large capacity borosilicate glass bottles, offered in four different sizes, feature a hose connector sealed at neck (1/2 or 3/8" connection). All bottle necks are compatible with a #12 stopper.

  • Superior Pressure Caps

    Wilmad-LabGlass - SP Scienceware

    The superior pressure cap is ideal for experiments that requires a simple gas tight seal under 1.5 bar. Recommended to use with Wilmad medium wall or heavy wall tube. This cap would not allow syringe puncture. Use heat gun to soften the cap and apply on the tube. Once the cap is cooled down, a gas…

  • NMR/EPR Tube Caps

    Wilmad-LabGlass - SP Scienceware

    Our PTFE NMR/EPR Tube Caps are machined to exact specifications with smaller gyroradius and more homogeneous mass distribution than disposable caps providing better spinning stability. They are recommended for experiments at high - ultra high field and those using Chloroform as the reference…

  • Solid State NMR Cap Remover

    Wilmad-LabGlass - SP Scienceware

    One of the most challenging parts of a solid state NMR experiment is to remove the end cap or base plug. This Zero turn cap remover eliminates possible damage of the cap and rotor.

  • 5mm Doty® Susceptibility Plugs

    Wilmad-LabGlass - SP Scienceware

    Traditionally, sample sizes are 3-5 times the height of the probe R f coil. All magnetic field distortions caused by susceptibility discontinuities at the upper air-sample and lower glass-sample interfaces were far from the sensitive probe R f coil region. Small samples diluted to larger…

  • Hubbard Specific Gravity Bottle

    Wilmad-LabGlass - SP Scienceware

    This borosilicate glass specific gravity bottle is used in standard test methods for specific gravity of a variety of semi solid materials and emulsions, such as asphalt cements, road tars, road oils, and soft tar pitches. The solid Standard Taper stopper has a hole approximately 1.6mm in diameter…

  • Cap for Automated Systems

    Wilmad-LabGlass - SP Scienceware

    Wilmad 4 inch (-102 mm) long Agilent Precision Automatic Sample Changer Tubes have the tightest outer diameter tolerance (0.0065 mm) to prevent jamming. Cap for Automatic Sampler Only.

  • 3mm Doty® Susceptibility Plugs

    Wilmad-LabGlass - SP Scienceware

    Traditionally, sample sizes are 3-5 times the height of the probe R f coil. All magnetic field distortions caused by susceptibility discontinuities at the upper air-sample and lower glass-sample interfaces were far from the sensitive probe R f coil region. Small samples diluted to larger…

  • Tall Form Weighing Bottles with Flat Top Cap

    Wilmad-LabGlass - SP Scienceware

    Caps can be used as weighing dishes External standard taper joint allows for sample transfer without seal interference Flat top permits stacking for increased desiccator capacity High form shape decreases bottle footprint Light weight for simple tare settings Manufactured from ASTM…

Compare Tool

Select up to 3 products

Please Log In

Don't have a web profile? Create one now.