Schlenk style reaction tube for vacuum and No-Air applications. Available in many capacities, joint sizes and side arm configurations including a glass stopcock, 0-3 inlet valve or a 0-4 Hi-Vac valve.

Carbon Adsorbers and Filters Change Indicators for Ammonia, Ammonia & Hydrogen Sulfide, Hydrazine and Hydrogen Sulfide. The breakthrough (saturation) indicators are colorimetric indicators that indicate the saturation and exhaustion of carbon adsorbers and filters. The indicators are…

The MD8 series of air samplers are monitoring devices combined with novel filtration systems for the exceptional recovery of airborne microorganisms. MD8 AirScan: (Integrated) Quantitative detection in sterile areas such as clean rooms/RABS, isolators, or blow-fill-seal machines. …

Flexible Non contaminating Septum closure Use for gas or liquid sample containment Heat-sealed seams for leak-proof operation Reusable bags made of 2 mil PVDF fluoropolymer film, Chemware® Gas Bags offer an economical alternative for analysis of non-corrosive gases. Durable, heat-sealed seams…

Carbon Adsorbers and Filters Change Indicators for Acids, Ammonia, Ammonia & Hydrogen Sulfide, Aromatic Diisocyanates, Basic Vapors, Halogens, Hydrazine, Formaldehyde, Hydrogen Sulfide and Mercury. The breakthrough (saturation) indicators are colorimetric indicators that indicate the…

Glass Manifold with #15 Ace-Thred at either end To allow switching 5853 vacuum connection to left or right side. Supplied with three or five, 4mm straight bore PTFE stopcock sampling ports. (Additional ports can be ordered.) Overall length of glass manifold is 230mm. Complete item consists of 8763…

Automatic, adjustable pressure release valve for safer operation of pilot plant or other assemblies where the pressure is of great concern. The tension on the stainless steel spring determines the amount of pressure needed to force the lower piece open. With the spring supplied, the range is 15-50…

Aluminum blower mount for connecting 7511 blower to glass manifold. With threaded stock.

A high velocity impinger for the determination of dust concentration in air or other gases. Total volume is approximately 500mL. Bottle joint is 45/50. Inlet/outlet are 12.5mm O.D. Modified versions available with spherical joints both vertical for connecting in series. Available with or without…

Single tube vacuum manifold with #15 o-ring joint ends. Available with 3 or 4 high vacuum stopcock ports. Order with inner joint port ends (14/20 or 24/40) or #15 o-ring joints. The distance between ports is 95mm, ideal for flasks up to 250mL. Please see our various o-ring joint adapters such as…

The ESS Air Sampling Bag incorporates a two opening system for sampling and extraction. The side port/stem (3/16" OD) allows filling with a pneumatic pump and tubing, and for rapid emptying of the bag. The top of the valve is

Double tube vacuum manifold with 4 x #15 o-ring joint ends. Available in 3 or 4 port configuration with Easy Action 0-10MM stopcocks. The ports can be ordered with either 14/20, 24/40 inner joints or #15 o-ring joints. Distance between ports is 100MM which will allow for flasks up to 250mL. Please…

Sampling tee with top threaded, side and bottom tubes reduced for use with 7506 bushing.

All-glass check valve with ground seat and precision ground solid ball. Suitable with mercury in the vertical position, more sensitive to other fluids in the horizontal position. Connections are 8mm O.D.

Real-time filter breakthrough indicators. You don't have to change your filter in 3 months, 6 months or 9 months, change your filter only when exhausted and saturated using real-time breakthrough indicators. Get the most use of your filters and protect yourself from exposure to toxic chemicals.…

Straight tube type air sampling cane with polyethylene hood and stainless steel brackets. Codes -35 & -37 feature a #7 Ace-Thred port for introducing calibration gases.

A high velocity impinger (Ref. AGI-30) which passes 12.0 to 13.0L/min. (corrected to engineering standard gas conditions) when the pressure drop across the orifice is 41cm Hg or greater. Stopper fits 24/25 125ml bottle and features a 11mm OD center tube, 8mm OD side arm with bulge, 0.05in capillary…

An all-glass check valve with ground seat for liquid seal. Available in style A for vertical use, and style B for right angle connection. Connections are 8mm O.D.

A rapid, efficient and foolproof Purge Valve for 100% replacement of air in reaction vessels with any desired gas (N2, H2, Ar, Cl2, etc.). No mercury used, no reducing valve needed on gas source, no high vacuum source necessary. No need to watch manometers, hand control gas flow, or install warning…

Vacuum, NO-AIR adapter for vacuum cart, vacuum manifolds and Schlenk lines. Has No. 15 O-Ring joint side port with a Hi-Vac valve for precise flow control and an ACE-THRED bottom outlet.

Impingers used for sampling small air volumes at low velocities. Bottle with 24/40 stopper joint is available in 25 or 30ml sizes. The stopper is available with an open nozzle or one calibrated to deliver 0.09 to 0.11 CFM at 30.5cm (12in) vacuum. The stopper inlet is available as an open tube end,…

Adjustable bleed adapter used for reducing air flow in the Air Sampling Manifold to prevent a pressure drop across the sampling ports. Normally installed in front of the 7511 blower, in line with the manifold. Positioning of holes in threaded nylon plug controls the volume of air flow. Plug…

Permanent split capacitor, steel housed blower used to pull air through our Air Sampling manifolds. Blower produces 50 cfm @ 0.0 meters of water static pressure which assures a minimum pressure drop across each port in the manifold train. Free air rpm is 3030. Available in both 115 & 230v…

Bubbler with either fritted tip or plain orifice stopper. Bottle has 24/40 joint and 10 cm tube below bulge. Stopper has 12/5 outer joint on inlet arm and 12/5 inner on outlet arm. Fritted tip is porosity C (25-50m). Orifice tip is 1.5mm capillary with end tapered. Approximate capacity, with…

The MAS-100 NT® microbial air monitoring systems are high performance, portable, battery operated instrument which are based on the principle of the Andersen air sampler. These compact yet sophisticated devices are the preferred choice for those demanding the highest quality in microbial air…

Carbon adsorbers and Filters Change Indicators for Ammonia, Ammonia & Hydrogen Sulfide, Hydrazine and Hydrogen Sulfide. The breakthrough (saturation) indicators are colorimetric indicators that indicate the saturation and exhaustion of carbon adsorbers and filters. The indicators are…

Glass Manifold with #15 Ace-Thred at either end to allow switching vacuum connection to left or right side. Supplied with three or five 0 - 4mm High Vacuum, Easy Action Stopcocks for sample ports. Plugs are PTFE with Nylon hooded handles and FETFE O-Rings. Ultimate vacuum of 10 - 7 can be realized…

Primarily designed for use with ACE 8051 bearings. The inner tube through which the stirring shaft passes, plus the PTFE O-Ring supplied with each unit, prevents the lubricant or foreign particles from contaminating the flask contents. For replacement PTFE ring, order 8113-89.

Graduated Schlenk storage tube with 14/20 or 24/25 outer top joints, 14/35 or 24/40 inner joint side arms, stopcock inlet or hose barbed inlet valve. Reaction accessories include 7759 series filter tubes, 7807 series finger condenser, 9543 series stoppers and 13657-33 stirring magnet..

With standard U shape gauge made of heavy barometer tubing and mounted on a wooden panel for vertical suspension. The scale is adjustable and accurately calibrated. Supplied with scale and tubes, but without mercury.

A high velocity impinger air sampling which passes 6L/min (corrected to engineering gas conditions) when the pressure drop across the orifice is 41cm Hg or greater. Stopper fits 24/25 125ml bottle and features a 11mm OD center tube, 8mm OD side arm with bulge, 0.035in capillary tip that is…

Schlenk style flask for vacuum, NO-AIR or gas applications. Can be used for storage or reactions. Top is either a no.15 o-ring or outer standard taper joints. Side arm has either a 0-3 inlet valve or a 2mm or a 4mm glass stopcock.