Glass Bearing

Compare Tool

Select up to 3 products

Glass Bearing
1 - 32 of 100
Sort
View
Show
  • Bearing, Trubore, Glass, Heavy Duty, 19mm

    Ace Glass

    Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique 3 piece design of Trubore inner bearing, compression seal nylon bushing and glass standard taper adapter allows for moderate misalignment of stir motor and the bearing cannot sieze the shaft. For use with 8077 & 8078 19mm od…

  • Safe-Lab® PTFE Bearing Inserts

    Bel-Art Products

    Not autoclavable. 2 per pack. Use with 10mm stirring rods. Replacement bearings for use with Safe-Lab® Joint Stirrer Bearing

  • Spinner Bearing NMR Tube Tester

    Wilmad LabGlass

    …success in high field NMR experiments, this tester will ensure shimming quality of your glass tubes. Useful in labs that wash, dry and reuse precision NMR tubes Warped tubes will bind in the spinner bearing while good tubes spin freely Keep a tube tester beside every NMR spectrometer…

  • Polished Glass Stirrer Shafts

    Wilmad LabGlass

    Precision ground and polished, these borosilicate glass stirrer shafts have a 10mm O.D. For use with LG-9475T bearing with PTFE bearing surface, or other bearings with a PTFE interface with the same bore. Features a side button at bottom for attachment of any of the stirrer/stirring blades (LG-9505…

  • Precision PTFE Stirrer Bearings

    Wilmad LabGlass

    …finish rods from other manufacturers are not recommended for use with this bearing. Complete 10mm diameter assembly includes PTFE stirrer bearing, PTFE bushing, saddle O-ring (LG-9470-300), threaded heavy wall borosilicate glass adapter, and top cap (LG-10818-114). See LG-9501 for polished stirrer…

  • Bearing, High Speed Vacuum, 10mm

    Ace Glass

    Bearing, Trubore, glass, high speed, vacuum, 9mm, 24/40.

  • Bearing, Trubore, Pressure, Ace-Threds, 10mm

    Ace Glass

    Glass bearing design for use with Ace-Thred pressure reactors and our 8075 glass, polished or 8074 bare, stainless steel 10mm stirring shafts. Both the top bushing and bottom coupling are PTFE. Maximum operating speed is 600 rpm.

  • Bearing, Trubore, Heavy Duty, 19mm

    Ace Glass

    Trubore stirrer assembly consists of the standard taper outer glass bearing, PTFE inner bearing, glass-filled PTFE bushing and lock nut, compression seal saddle o-ring, PTFE blade and either a glass or stainless stir shaft.

  • Stirring Shaft, 10mm, Precision Ground Glass

    Ace Glass

    Precision ground glass stirring shafts, 10mm OD, paddled, button type and bead type. Button type shafts accept 8083, 8085, 8086, 8087 & 8096 stir blades. Beaded shafts accept 8088, 8089, 8090 & 8091 agitators. Use with Trubore bearings 8036, 8038, 8039, 8040, 8042, 8043, 8047, 8051, 8053 & 8055. Use…

  • Stirring Shaft & Agitator, Glass or PTFE,5mm, Precision

    Ace Glass

    Stirring shaft agitator combination available in either a solid, precision ground glass shaft or all PTFE knob type shaft with a PTFE snap-fit agitator designed to fit through 14/20 and 18/11 joints. Designed for use with our 5mm ID 9524 or 9527 bearings and flasks of 50ml and smaller.

  • Bearing, Trubore, 10mm

    Ace Glass

    …the length of the bearing, a stirrer is produced that will hold to within 1mm of vacuum and withstand pressures in the flask up to 300mm. The 9532 Agitator, used with this bearing actually develops a negative pressure of 230mm water at operation speeds. The side opening on the bearing is used to add…

  • Bearing, Trubore, Plain, 10mm

    Ace Glass

    Interchangeable bearing designed to be used with our precision ground stirring shafts (8068,8070,8071,8073,9532,9533). Recommended top stirring speed with our 8117 Stir-Lube is 1500 rpm.

  • Bearing, Trubore, Water-Cooled, 10mm

    Ace Glass

    Interchangeable, ground joint bearing with jacket for water cooling. May be operated as high as 2000 rpm using our 8119 high-speed lubricant. Can be operated at 1500 rpm unevacuated using our 8117 Stir-Lube. Hose connections for use with 5/16" or 3/8"ID tubing. Available with PTFE clad joint to…

  • Bearing, Trubore, Economy, 6mm

    Ace Glass

    Trubore bearing, heavy duty, standard taper joint, self-aligning. Unique design is forgiving of slight misalignment of stir motor and shaft. Recommended for use with our 9534 6mm precision ground stir shaft.

  • Bearing, Trubore, Ace-Thred, 10mm

    Ace Glass

    …three-piece bearing. Complete consists of inner Trubore bearing, Nylon bushing with O-Ring, and threaded adapter. Unique design eliminates costly replacement since inner bearing will spin if shaft binds or will self-align at O-Ring seal in the event the motor is slightly cocked. Inner bearing and…

  • Bearing, Trubore, Pressure, 10mm

    Ace Glass

    Designed for use with #25 Ace-Thred. Consists of a Trubore bearing, pressure bushing, gland with two O-Rings and retainer bushing with o-ring. For use with our precision ground stirring shafts (8068,8070, 8071,8073,9532,9533) and reservoir as part of our 7898 Thin Film reaction system.

  • Bearing, Trubore, Vacuum, 10mm

    Ace Glass

    For use with aluminum packing box in low positive pressure and vacuum applications. Using the graphite-impregnated PTFE packing and ACE Stir-Lube, pressures down to 7 microns have been obtained at 170rpm using only a mechanical pump. Speeds over 1000rpm are not advisable due to heat generated.…

  • Bearing, PTFE, Non-Shedding, Ultra-Vacuum

    Ace Glass

    Ultra-Vacuum stirrer bearing for applications up to 0.6 Torr. Non-shedding bearing is manufactured from PTFE, Rulon and PEEK materials. Equally good in both vacuum and pressure applications as low as 0.6 Torr. Rated for up to 400 rpm with both glass (polished rather than precision ground is best)…

  • Bearing, Trubore, PTFE Inner Liner, 19mm and 28mm

    Ace Glass

    Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8076 (19mm od) or 8080 (28mm od) polished glass stir shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…

  • Bearing, Trubore, PTFE Liner for Polished Shafts, 10mm

    Ace Glass

    Self-aligning, lubricant free PTFE Trubore bearing or combination bearing / debris trap. Use with 8074 stainless steel or 8075 polished 10mm od glass shafts. Debris trap model prevents bearing-wear particles from contaminating the reaction vessel and has a side port for clean-out, evacuating or…

  • Stirrer, Complete

    Ace Glass

    Trubore stirrer assembly consists of the standard taper outer glass bearing, PTFE inner bearing, glass-filled PTFE bushing and lock nut, compression seal saddle o-ring, PTFE blade and either a glass or stainless stir shaft.

  • Bearing, Trubore, Material Introduction, 10mm

    Ace Glass

    Bearing is especially useful in controlled atmosphere work when used with our 8068 solid shaft and balancing pressure differentials across the bearing. Material introduction or gaseous dispersions can be obtained using our 8068 hollow, precision ground stirring shafts.

  • Bearing, Trubore, High Vacuum, 10mm

    Ace Glass

    This bearing is the standard liquid seal type except that the use of Trubore tubing enables this unit to perform very satisfactorily under high vacuum conditions. Use our precision ground stirring shafts (8068,8070,8071,8073,9532,9533).

  • Stirrer Bearing, PTFE, 6-10MM Shafts

    Ace Glass

    …available for 6, 8 and 10mm glass, metal or PTFE stir shafts. Can be used in slight pressure or vacuum applications. Maximum recommended speed for continuous operation is 500 rpm. Unlike traditional bearings, the upper portion rotates with the shaft like a collet. Bearing bottom is a standard taper…

  • Bearing, Trubore, 5 & 6mm

    Ace Glass

    Trubore bearing with standard taper joint for use with our 9534, 9535 and 9541 precision ground stir shafts. Lubricant well at top will accept enough 8117 Stir-Lube to provide hours of operation at up to 1000 rpm. Match bearing ID with stir shaft OD.

  • Bearing, Trubore, Gas Balancing, 10mm

    Ace Glass

    This bearing is supplied with tubulation for feeding inert gases around the bearing to balance any pressure possibly being developed in the flask. Can also be used for gas-liquid reactions and gas dispersions using our hollow precision ground stirring shafts (8068, 9532).

  • Bearing, Trubore, Water Cooled, 19mm

    Ace Glass

    Trubore bearing, jacketed, spherical joint. Designed to accomodate our 8112-10 packing box. For use with 8077 & 8078 19mm od precision ground glass shafts or 8079 PTFE covered shafts. Spherical joint can be clamped to prevent rotation. Trubore length of 15.2cm or 6 inches.

  • Bearing, Trubore, Single Joint, 10mm

    Ace Glass

    Interchangeable ground joint bearing for use with our precision ground stirring shafts (8068,8070,8071,8073,9532,9533). Recommended top stirring speed with our 8117 Stir-Lube is 1500 rpm.

  • Bearing, Trubore, Water Cooled, 19mm

    Ace Glass

    Trubore bearing, jacketed, standard taper joint. For use with 8077 & 8078 19mm od precision ground glass shafts or 8079 PTFE covered shafts.

  • Bearing, Trubore, Water Cooled, 5 & 6mm

    Ace Glass

    Jacketed, Trubore bearing with standard taper joint for use with our 9534, 9535 and 9541 precision ground stir shafts. Hose connections fit 5/16" or 3/8" ID tubing. Match bearing ID of 5 or 6mm to stir shaft OD.

  • Stirrer, Complete

    Ace Glass

    Precision Trubore Stirrer Assembly consisting of 10 mm ID bearing, bushing, precision ground, button type glass shaft and blade. Available with either glass or PTFE stir blade.

  • Stirring Shaft, Glass, 5&6mm, Polished & Precision Ground

    Ace Glass

    Button type, solid glass stirring shafts, 5 & 6mm OD. Precision ground shafts, codes -04 & -06, should be used in matching glass Trubore 9524 and 9527 bearings. Polished shaft, code -40, should be used only in our 8066-120, 6mm PTFE inner bearing. All accept our 9542 blades. Join to stirrer motor…

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.