Synthware distillation adapter with sealed in drip tip. Adapter is bent at 105 degrees. Standard taper top outer joint and lower inner joints. 

Peptide Synthesis Vessel, Solid Phase, Synthware, Capacity: Available in sizes ranging from 10-50mL, Frit Porosity: Coarse or Medium, Frit Diameter: Available in sizes ranging from 15-25mm, GL Thread: 14 or 25 available, Arm OD: 8mm, Supplied with a PTFE lined cap and straight bore PTFE stopcock…

Solvent Still, Built-In Condenser Capacity: 125mL Joints: 24/40 Threaded Side Port: 14/10

Solvent Still Head, Repurification Joint: 24/40

Synthware distilling adapter with top compression cap. With same size standard taper inner joints on bottom and side arm. Cap accomodates 5.0 - 7.5mm O.D. thermometer. Supplied with one Nylon cap and one Viton o-ring.

Thermometer Adapter, Vacuum, Microscale, Synthware, Joints: 14/10, Thermometer OD: 5.0-7.5mm, supplied with one compression cap and one Viton O-ring.

Allows for flexible tubing to be connected to apparatus for introduction of vacuum or pressure. 

Synthware inlet adapter with a standard taper inner joint. Design allows introduction of reactants below the surface. The serrated hose connections have an O.D. of 10 mm.

Synthware Inert Gas Adapter has two hose connections 180 degrees from one another to provide a flow of inert gas over the apparatus. The joints are standard taper inner joints.

Adapter is placed above flask to prevent carry-over of reactions which have a tendency to foam. With top outer and lower inner standard taper joints.

Distillation Head, Vigreux, Jacketed Thermometer Joint: 10/18 Joints: 14/20, use with 25mm immersion thermometer

Inlet Connecting Adapter, High Vacuum Valve Joint: #15 O-ring Valve Size: 0-4mm Side Port: 10mm OD.

Solvent Still Head Capacity: 500 and 1000mL available Top Joint: 24/40 Bottom Joint: 24/40 and 29/42 available Side Joint: 14/20 Drainage Port Joint: 14/20

Vacuum Takeoff Adapter, Microscale, Synthware, Joint: 14/10, supplied with one compression cap, one Viton O-ring and one PTFE-faced silicone septum.

Column length is measured from the highest to lowest indent in the column.

Tubes are graduated from 0-3mL in 0.2mL subdivisions.

Microscale Distillation Apparatus has a short-path design for microscale application, used with 25mm immersion thermometer, and D27 distillation receiver.

Check Valve, All Glass, Synthware, Hose Connections OD: 8mm, with ground seat for liquid seal.

Gas Inlet/Outlet Adapter, Microscale, Synthware, Joint: 14/10, Hose Connection OD: 8mm.

Synthware vacuum or inert gas adapter has a T-bore glass stopcock allowing vessels with a standard taper outer joint to purged and evacuated. The stopcock has a constant pressure retention device and a 4 mm bore.

Vacuum Adapter, Microscale, PTFE Stopcock, Synthware, Joint: 14/10, Stopcock Bore: 2mm, Hose Connection OD: 8mm.

Rotating distillation receiver allows four fractions to be collected. Vacuum adapter has a vertical orientation.

For use with gas inlet tubes or plain stem thermometers. Supplied with one holed rubber adapter.

With an outer standard taper joint at the top. The tapered delivery drip tube extends into open receivers.

Bleed Tube.

Synthware adapter with oil bubbler. With standard taper inner joint. Horizontal design allows for in line connection for apparatus purging.

Synthware inlet adapter with an extra coarse porosity fritted disc between the serrated hose connection and the standard taper inner joint. The disc prevents solids from being introduced into the reaction system during liquid transfer.

Joint Sleeve, PTFE, Ribbed with gripping ring, Synthware, Sizes available to fit various joint sizes.

Claisen Adapter, Microscale, Synthware, Joints: 14/10, supplied with two compression caps, two Viton O-rings and two PTFE-faced silicone septum.

Synthware distillation adapter with threaded thermometer port. The threaded port will accommodate a 6-7.5mm O.D. plain thermometer. The adapter has standard taper top outer joint and inner joints for the bottom and side. All joints are the same size. 

Vacuum jacketed Vigreux distillation head having a sealed on condenser, braced for strength. Vacuum adapter has an inner joint and a sealed in drip tip. To be used with a 25mm immersion thermometer .

Trap is placed between the vapor tube and the evaporation flask. This design prevent possible contamination in the event of bumping. With upper outer and lower inner standard taper joints.