Agilent Technologies

Compare Tool

Select up to 3 products

All Products

Agilent Technologies

1 - 32 of 1158
Sort
View
Show
  • Polypropylene Screw Caps with Septa

    Agilent Technologies

    Polypropylene screw tops are for wide opening screw top vials. Precision-fit septa provide an evaporation-proof seal.

  • Vial Racks

    Agilent Technologies

  • 20 mm Crimp Caps with Septa

    Agilent Technologies

    Line of pre-assembled crimp caps come with septa. Caps are ready to use with any headspace crimp top vials. Caps with safety feature release pressure at approximately 45 psi.

  • Solvent Filters/Degassers

    Agilent Technologies

    Removing contaminants from solvents Degassing solvents in systems lacking on-line degassers Filtered solvents decrease piston wear from particulates Increase column life Eliminate pump downtime caused by air locks in check valves Filter into safe plastic-coated or…

  • Base assembly, for 96-well plate manifold

    Agilent Technologies

    The base accomodates lids that hold either a user-defined selection of flexible cartridges, or fixed format 96-well plates with each well loaded with the same sorbent.

  • Big Universal Traps

    Agilent Technologies

    Big Universal Traps utilize a layered, multi-adsorbent bed packing of the most effective, highest capacity adsorbent materials available today for the removal of oxygen, moisture, hydrocarbons, carbon dioxide and carbon monoxide from helium gas streams. The volume of the various adsorbent materials…

  • GS-Gaspro

    Agilent Technologies

    Bonded PLOT column technology Suitable for light hydrocarbons and sulfur gas Retention stability not affected by water Separates CO and CO2 on a single column Ideal PLOT column for CG/MS - no particles Temperature limits: -80° to 260°/300°C …

  • DB-5ms

    Agilent Technologies

    Phenyl Arylene polymer virtually equivalent to a (5%-Phenyl)-methylpolysiloxane Non-polar Very low bleed, suitable for GC/MS Exhibits inertness to active compounds Temperature limits are -60° to 325°/350°C Improved signal-to-noise ration for increased sensitivity and mass…

  • ADM Flow Meters

    Agilent Technologies

    Accuracy ±3% Operating temperature range: 0 to 45°C for instrument/-70 to 135°C for tubing Calibration traceable to NIST primary standards Measures flow rates from 0.5 to 1000 mL/min Split ratios ADM flowmeters allow most gas measurements with the touch of…

  • Pre-Assembled, 2 mL Wide Opening Screw Top Glass Vial Convenience Packs

    Agilent Technologies

    Pre-assembled packs come ready-to-use with cap and septum of your choice attached to the vial. A time/labor-saving product for use on your Agilent Autosampler or any rotating tray automatic sampler.

  • Solvent Filters for G1311/12/54A Pumps

    Agilent Technologies

    Unfiltered solvents or solvents contaminated with microbial growth can clog solvent inlet filters, reducing the lifetime of the filter and impacting pump performance. Remember to clean or replace the solvent inlet filters at least once every 3 months.

  • Autosampler Syringes

    Agilent Technologies

    Needle Styles Broad selection of syringes for manual and auto injection to provide accurate and effective sampling Tapered or straight needles Fixed Needle Syringe The epoxy-cemented, stainless steel needle is centered in the syringe barrel at the depth of the zero…

  • Manual Crimper and Decappers

    Agilent Technologies

    Use with all 8, 11 and 20 mm crimpt top vials and crimp caps

  • DB-624

    Agilent Technologies

    Specifically designed for the analysis of volatile priority pollutants No cryogenics needed for U.S. EPA Method 502.2 Excellent for U.S. EPA Methods: 501.3, 502.2, 503.1, 524.2, 601, 602, 8010, 8015, 8020, 8240 and 8260 Exhibits inertness to active compounds Bonded and cross-linked Solvent…

  • Capillary Column Ferrules

    Agilent Technologies

    Capillary ferrules are packaged in dial packs which deliver one ferrule at a time, keeping the others clean and ready for use. The dial packaging has been tested to ensure no out gassing of contaminants, including phthalates. *These ferrules are recommended for use with Agilent GC/MS…

  • Packed Column Inlet Supplies

    Agilent Technologies

  • Liner O-Rings

    Agilent Technologies

    Agilent fluorocarbon liner O-rings Liners are sealed in the inlet with O-rings or graphite seals Graphite seals are used when inlet temperatures exceed 350°C Fluorocarbon O-ring seals are easier to replace than graphite that deforms and flakes apart Pre-cleaned, then conditioned to eliminate…

  • Microvolume Inserts For Wide Opening Vials

    Agilent Technologies

    Transform Agilent vials from full-capacity to limited volume with one simple step. Inserts are compatible with Agilent wide opening screw top, crimp top and snap top vials. Conical Inserts with Polymer Feet (2714M52, N29, N42) With the correct default setting on an autosampler, these inserts…

  • Split/Splitless Inlet Supplies

    Agilent Technologies

    2714R07 is for use with total inlet flow rates of less than 200 mL/min.

  • Septa

    Agilent Technologies

    For wide opening vials For use with screw caps Also called “red rubber”

  • Headspace Vials

    Agilent Technologies

    Beveled top for maximum secure seal Two neck lengths are available Flat or rounded bottom designs Beveled neck vials are available in both 10 mL and 20 mL capacities, flat or rounded bottom. The 20 mm crimp caps provide a consistently secure seal. Flat-bottom headspace crimp top glass vials…

  • HTC PAL Liquid Injection Vials and Caps

    Agilent Technologies

    Agilent provides a wide variety of vials and cap compatible with the HTC LC Injector listed in the Vials and Caps section. CTC recommends using Silicone/PTFE and PTFE/Silicone/PTFE septa for purity and penetration properties. Below are featured the most popular vials and caps used with the HTC.

  • Septa

    Agilent Technologies

    Multiple styles in tri-fold blister packs Fits 4890, 5890, 6850 and 6890 GCs Precision molded for accurate fit Premium 11 mm Bleed and Temperature Optimized (BTO)Septa feature a recess on the injection side that guides the syringe needle to the same point with every injection.…

  • Stainless Steel Sample Loops

    Agilent Technologies

    Sample loops for Rheodyne 7725 Series and 7125 Series valves are not interchangeable due to the change in port angle Actual volumes can differ due to tolerance of metal tubing bore Accuracy of large metal loops is ±5%, intermediate loops ±10%, small loops ±30%

  • Vaccuum Manifolds And Accessories

    Agilent Technologies

    Agilent manifolds and accessories complement the quality of AccuBOND II sorbents. Flexible configurations and availability as complete assemblies or individual components mean that the user has the necessary capability at any stage from method development to high throughput operation. Vacuum…

  • High Recovery Glass Vials

    Agilent Technologies

    Crimp top 1.5 mL capacity Wide opening 1.5 mL wide opening crimp top high recovery vials have a 30 µL reservoir. High recovery glass vials are for sample concentration and injection without transferring to microvolume inserts.

  • DB-1301

    Agilent Technologies

    (6%-Cyanopropyl-phenyl) methylpolysiloxane Equivalent to USP Phase G43 Low/midpolarity Bonded and cross-linked Exact replacement of HP-1301 Solvent rinsable Similar Phases: Rtx-1301, PE-1301

  • Wide Opening Screw Top Glass Vials

    Agilent Technologies

    Agilent provides a wide variety of vials and cap compatible with the HTC LC Injector listed in the Vials and Caps section. CTC recommends using Silicone/PTFE and PTFE/Silicone/PTFE septa for purity and penetration properties. Below are featured the most popular vials and caps used with the HTC.

  • Purge Valve

    Agilent Technologies

    Common to all 1100/1200 pump modules, the purge valve has a gold seal held in place with a plastic cup The most frequently replaced item in the 1100/1200 Series pumps is the purge valve PTFE frit, which can clog with seal material or solvent particulates When replacing the frit,…

  • Inlet Seal Gold with washer

    Agilent Technologies

  • ZORBAX Bonus-RP

    Agilent Technologies

    RR: Rapid Resolution 3.5 µm

  • HP-5ms

    Agilent Technologies

    Meets EN14331 Standards (5%-Phenyl)-methylpolysiloxane Non-polar Very low bleed, suitable for GC/MS Exhibits inertness to active compounds Temperature limits are -60° to 325°/350°C Improved signal-to-noise ration for increased sensitivity and mass spectral integrity Bonded and cross-linked…

Compare Tool

Select up to 3 products

Please Log In

Don't have an Account? Create one now.