Ace Glass
-
PTFE agitator with removable blade secured with a PTFE pin. Supplied 3.2x15.2cm blade will fit through a 45/50 joint. Fits 19mm od drilled type or knob type 8076, 8078 & 8079 shafts.
-
Moisture Test Receiver
Ace GlassUsed in phosphorus determination according to Ind. & Engr. Chem., Anal. Ed., Vol 9, page 524. Receiver capacity 5mL, graduated in 0.05 mL subdivisions. Upper joint is standard taper 24/40, side arm joint, standard taper 45/50.
-
Condenser, West
Ace GlassNo Hold Up West condenser available with hose barbs or Ace-Safe connectors.
-
-
Buret, Smith Type, Weighing
Ace GlassSmith Buret for dispensing precise quantities of liquids. The wide base adds stability when placed on a balance pan. Complete apparatus consists of a flask, buret and cap stopper. With a 19/10 cap type stopper joint as illustrated, and a standard taper
-
Air Sampling Collection Bottle
Ace GlassCollection bottle, usually connected to the bottom arm of the 7495 tee with reduced ends, to collect heavy particulates before they enter the manifold train.
-
Caps, GL Thread - Duran®
Ace GlassScrew caps and pouring rings for use with GL threaded bottles. For steam autoclaving, we recommend PBT (polybutylene theraphthalate) caps with a PTFE liner, -45 to 180 degrees C rated. Polypropylene is only rated to 140 degrees C. 316L stainless steel cap is for use with stainless steel laboratory…
-
Round bottom, single neck flask with stopcock septum port side arm for use with air-sensitive material. Features a PTFE, 2mm bore stopcock. Available in standard wall and heavy wall versions. All flasks supplied with a 9096-32 septum.
-
Moisture Test Receiver
Ace GlassModified Bidwell & Sterling with overflow to allow excess solvent to return to boiling flask. Both capacities are calibrated in 0.1mL subdivisions. Joints are standard taper 24/40.
-
The improved design of ACE extractor condensers permits greater condensing capacity, cycling rates may be doubled over conventional style extractors. Complete consists of flask cap, condenser, extractor, and flask.
-
Vacuum Gauge, McLeod
Ace GlassAccurate to within plus or minus 3%. The McLeod gauge is the most convenient and economical instrument for measuring low pressures from 1 micron up. The ACE McLeod gauge is offered in four ranges, so that it is possible to accurately measure any pressures between 1 micron and the highest reading on…
-
Fritted filter disks for Ace Membrane Filtration Apparatus. Special tight outside diameter and tolerance to fit 3702-10 and 3700-10 filter adapters.
-
Funnel, Separatory, Squibb, Pear-Shaped
Ace GlassSeparatory funnel featuring a glass stopcock and a PTFE stopper included. See Ace family 12632 for extra stoppers.
-
High performance, low cost, effective in separating low-boiling liquid mixtures with volumes in 0.5 - 5mL range. 2.5" micro-distillation column separates close-boiling mixtures utilizing a PTFE band uniquely driven by an attached magnet. Complete assembly features either 10/10 joints, code -43, or…
-
Clamp, Reaction Flask, Two-Piece
Ace GlassPositive, two-piece clamp for securing flat flanges as found on our 6504,6511 & 6516 reaction flasks. Powder coated, high strength aluminum clamp features three brass tilting bolts which will swing freely away from the top piece upon loosening the secu
-
Thermocouple Sensor, Julabo, Pt100
Ace GlassJulabo Pt100 sensors in stainless steel or PTFE coated stainless
-
With 24/40 standard taper outer joint and stopcock on hose connection outlet.
-
Heating Bath Oil, Silicone
Ace GlassAn extremely stable, medium viscosity, silicone oil. Available in two temperature ranges: Low Temp. maximum 180 degree C; or High Temp. maximum 230 degree C. Neither oil shows discoloration after 40 hours at maximum temperature.
-
Polished stainless steel stirring shafts, 10mm OD, drilled type with removable button. When used with 8066 PTFE bearing, a lubricant-free vacuum seal can be realized at speeds up to 200 rpm. Recommended for use with 8044,8050,8066,13443 and 13445 bearings. With button, shaft accepts…
-
Pressure Reactor, Two-Piece, Plain Flask
Ace GlassComplete, two-piece, plain flask, pressure reactor system designed to perform low to moderate positive pressure reactions, synthesis and catalysis. Reactor capacities range from 500ml to 5000ml and use Ace-Threds to achieve a leak-tight system. Two-piece (flanged flask and head) design allows the…
-
Complete reaction assembly utilizing an Ace-Thred instead of a ground joint for improved immersion well / cooling tube seal. Features a 14/20 angled joint for sparger tube, 24/40 vertical joint for a condenser and a #7 Ace-Thred thermometer joint. Actual working volumes are 40 to 50% of stated…
-
High vacuum stopcock that eliminates exposure to corrosive materials. Use to at least 13.6 Kg internal pressure. Variable openings from 0-3mm to 0-10mm. Ultimate vacuum of 10-7 can be realized with standard three seals. Smooth acting valve permits fine
-
Cap Stopper, Micro
Ace GlassWith 14/10 outer joint externally threaded for making O-RING-CAP-SEAL connection with mating inner joint. Supplied with cap and O-Ring. For replacement caps, see 9590-46; for O-Rings, see 7855-720.
-
Distilling Column, Indented, Hempel
Ace GlassWith standard taper joints and indentations to support packing. Length in centimeters refers to the length from the packing support to the bottom of the outer ground joint.,/p>
-
Sparger Tube, for Pressure Reactor, PTFE
Ace GlassSparger tube for use in #15 Ace-Thred with either ONE-PIECE or TWO-PIECE Reactors. Consists of a closed bottom, 1/2" O.D. tube with a 1/8" I.D. bore. Bottom of tube has two 3/64" holes, 90 degree apart; top has a 5/16" male thread for connecting to bot
-
Distilling Apparatus, High Boiling
Ace GlassUseful for separating higher boiling liquids that require a short pot-to-column distance to prevent excessive condensation. If pot bleed is desired a two-neck flask can be used. Thermometer joint is 10/18 for 9551, 25mm immersion.
-
Filter Material, Discs and Fabric
Ace GlassFilter material and discs (paper, PTFE, and polypropylene).
-
High vacuum stopcock with easy action plug that has blunt, flat end instead of the tapered end supplied with 8194 or 8195. This modification means stopcock is a quick opening model versus the variable opening 8194 and 8195. Vacuums of 10-7 can be reali
-
Chromatographic Column, With Filter Disc
Ace GlassChromatographic column with 24/40 joint at top, 2 mm bore 1:5 taper solid PTFE stopcock plug at bottom and porosity B (70 - 100 m) fritted disc sealed near bottom of tube. These columns also appear in expanded listing under 5871.
-
Ferrules, PTFE
Ace GlassThomas No. 1165H91 Ferrule, PTFE, 1/8inid hole, use with #7 Ace-Thred, pk12 Thomas No. 1165H92 Ferrule, PTFE, 3/16inID hole, use with #7 Ace-Thred, pk/12 Thomas No. 1165H93 Ferrule, PTFE, 1/4inid hole, use with #7 Ace-Thred, pk12 Thomas No. 1165H94 Ferrule, PTFE,…
-
Joints, Outer Member, Straight-Through
Ace GlassTubing is same diameter as reinforcing rings on the standard taper joint. The rings permit penetration by the clamp cushioning material, and permit firm support without the need for excessive pressure on the joint; also, strain on the joint is reduced from expansion due to temperature increase.…
-
With three necks and PTFE plug (5mm bore on 5000mL, 4mm bore on all other sizes) stopcock outlet. Available in standard and heavy wall. Heavy wall approximately 30% heavier than standard wall. For stopcock plugs, see 8224. For heating mantle, see 12039